Resumen del contenido incluido en la página 1
®
VDS102T
DROP-DOWN
VIDEO MONTOR
ON OFF AUTO
Installation Guide
Resumen del contenido incluido en la página 2
Important Notice An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in “park” or when the vehicle’s parking brake is applied. An LCD p
Resumen del contenido incluido en la página 3
MATERIALS INCLUDED IN THIS PACKAGE: 1) Over Head Docking Station (P/N 136-3955) – (1 pc) 2) Lamp Harness (P/N 112B3110) – (1 pc) 3) 2 Pin Power Wire Harness with choke (P/ N 112B3143) – (1 pc) 4) Hardware Package Screws (#4) – (8 pcs) Self Drilling Screws (#8) – (4 pcs) Nut – (4 pcs) 5) Trim Ring (P/N 102-4111) – (1 pc) 6) PODTVT (P/N 136-3877) – (1 pc) 7) Mounting Bracket (P/N 108-3856) – (1 pc) 8) Remote Control (P/N 136-3956) – (1 pc) 1 2 3 ON OFF AUTO 4 5 6 7 8 POWER FMM CHANNEL SELECT EJECT
Resumen del contenido incluido en la página 4
12 3 14 4 13 5 6 12 7 8 11 9 10 1. Infrared Sensor – Allows the remote control to operate the VDS102T and to control the shuttle when docked. 2. Three position Dome Light Switch Auto – Automatically switches on the dome lights in conjunction with the vehicle’s interior illumination. Off – The dome lights will not turn on in this position. On – Turns on the dome lights. 3. Dome Lights – Provide additional interior illumination. 4. Channel () Button – Used this button to increase the channe
Resumen del contenido incluido en la página 5
GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, Video Game, external amp, wireless headphones, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting. 4) Prep the vehicle by removing any interior trim necessary to gain access to vehicle's wiring as well as all areas where interconnecting wire harnesses wi
Resumen del contenido incluido en la página 6
VEHICLE PREPARATION: 1) Locate an accessory power source (+12v when key is in the ACC. and run positions, and 0v when key is off), and also a good ground generally, these wires can be found at the ignition switch or fuse-box. 2) The mounting method and location will vary from vehicle to vehicle, so this manual will only focus on the installation of the video monitor and related console accessories. 3) Generally, the best location for the video monitor is where the vehicle's factory dome light is
Resumen del contenido incluido en la página 7
TRIM RING INSTALLATION: This page only covers special installation considerations for the trim ring installation. If the docking station is to be installed in a vehicle with the trim ring, it may need to be trimmed to fit the contour of the vehicle headliner. 1) In this installation, the docking station is mounted directly to the overhead cross-member in the roof using the mounting screw bosses. These screw bosses should contact the cross-member directly (i.e.: no gap between the screw boss and
Resumen del contenido incluido en la página 8
MOUNTING THE TRIM RING VDS102 Roof Roof Support Headliner Mounting Bracket (4) Self-Tapping Screws Trim Ring Docking Station () 4 M5 Nuts NOTE: Use care when screwing the bracket to the roof support, so to avoid damaging the roof of the vehicle ~6~ ~6~
Resumen del contenido incluido en la página 9
` 1) Make the connections to the vehicle for the 12 pin wiring harness. 2) Connect power harness to vehicle’s electrical system by tapping into an accessory hot line and a good ground. 3) Verify all functions of the System before final mounting of the finished assembly. A/V Source Definitions: Shuttle, AV Input and TV *NOTE: If the original relay box P/N SIRSWB is installed, it recommended that the antenna for the wireless FM Modulator be unplugged. See Figure A for antenna location. **NOTE: Ext
Resumen del contenido incluido en la página 10
CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs. To determine which system you have you must locate the wires at the dome light. On a positive switched system, with all the doors closed and the lights out, both
Resumen del contenido incluido en la página 11
Negative Switched Dome Lighting Red / black - Lamp on Black / red - Lamp common To 12 pin Purple / brown - Lamp Auto connector To constant To constant Factory Door ajar switch or Body Control computer Troubleshooting: SYMPTOM: REMEDY: No power at Video Monitor Verufy +12 VDC on Red wire at 2 pin Power Harness behind video monitor. Verify ground connection with continuity test from known good ground to black wire at 2 pin Power Harness Power but no video or sound Verify that the correct source is
Resumen del contenido incluido en la página 12
For Customer Service Visit Our Website At WWW.audiovox.com Product Information, Photos, FAQ’s Owner’s Manuals 128-7347 © Copyright 2005 Audiovox Electronics Corp. 150 Marcus Blvd. Hauppauge, NY 11788
