Resumen del contenido incluido en la página 1
Primergy
PRIMERGY S60
Storage Subsystem
Xenia Fierley
Fujitsu SiemensComputers GmbH cognitas PS
81730 München
e-mail: email:manuals@fujitsu-siemens.com
Tel.: (089) 61001-157
Fax: 0 700 / 372 00000
U41221-J-Z156-1-74
Sprachen: En
Edition September 2001
Resumen del contenido incluido en la página 2
Comments… Suggestions… Corrections… The User Documentation Department would like to know your opinion on this manual. Your feedback helps us to optimize our documentation to suit your individual needs. Fax forms for sending us your comments are included at the back of the manual. There you will also find the addresses of the relevant User Documentation Department Copyright and Trademarks Copyright © 2001 Fujitsu Siemens Computers GmbH. All rights reserved. Delivery subject to availability; r
Resumen del contenido incluido en la página 3
German English
Resumen del contenido incluido en la página 4
Resumen del contenido incluido en la página 5
Contents 1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 Target Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.2 Notation Conventions . . . . . . . . . . . . . . . . . . . . . . . 2 1.3 Structure of the Manual . . . . . . . . . . . . . . . . . . . . . . 3 1.4 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resumen del contenido incluido en la página 6
Contents 7 FC Hard Disk Drives . . . . . . . . . . . . . . . . . . . . . . . 37 7.1 Handling Hard Disk Drives/HDD Modules . . . . . . . . . . . . 37 7.2 Installing/Removing HDD/Dummy Module . . . . . . . . . . . . 38 7.3 Hot Swap for FC HDD Modules . . . . . . . . . . . . . . . . . . 42 7.4 Identification Marks and Loop Addresses . . . . . . . . . . . . . 43 8 Plug-in Board Modules . . . . . . . . . . . . . .
Resumen del contenido incluido en la página 7
Contents 11.1.3 Server Management Status . . . . . . . . . . . . . . . . . . . 74 11.1.3.1 Server Management Status LED lights permanently . . . . . . 74 11.1.4 Storage Subsystem Switches OFF . . . . . . . . . . . . . . . 75 11.1.5 System will not boot after Installation of New HDD Modules . . 75 11.1.6 HDD READY Indicator does not light up . . . . . . . . . . . . . 75 11.1.7 Hard Disk Drives“ dead” on System Start . . . . . . . .
Resumen del contenido incluido en la página 8
Resumen del contenido incluido en la página 9
1 Introduction The functionality, mechanics and design of the PRIMERGY S60 storage subsystem are optimally adapted to the PRIMERGY Nxxx server compute- nodes. It can be used as rack or as floorstand model. In the 19-inch rack, the S60 subsystem occupies three height units. The PRIMERGY S60 storage subsystem use the fiber-channel technology and can accommodate up to fourteen 1-inch hard disk drives. The use of fiber-channel technology ensures high transmission speeds over long distances, us
Resumen del contenido incluido en la página 10
Target Group Introduction I When installing PRIMERGY S60 storage subsystems in connection with ServerView please install the ServerStart CD version 4.06 or higher on each of the connected servers. See ServerView documentation for notes concerning installing and update (see also “Related publications” on page 81). 1.1 Target Group The operating instructions are intended for the person responsible for installing the hardware and correctly operating the system. The operating manual contain all
Resumen del contenido incluido en la página 11
Introduction Structure of the Manual 1.3 Structure of the Manual The PRIMERGY S60 storage subsystem manual describes how to install and configure the subsystem and perform expansions or upgrades. You will find further information (see also entries in the chapter “Related publi- cations” on page 81): in the “Safety, Warranty and Ergonomics” manual in the documentation on the PRIMERGY server This manual consists of the following chapters: Important notes This chapter contains instructions o
Resumen del contenido incluido en la página 12
Technical Data Introduction Configurations This part of the manual gives configuration examples. Installation The activities needed to install and commission the storage subsystem are described. Troubleshooting This chapter contains advice on solving problems that occur on commis- sioning or during the operation of the storage subsystem. 1.4 Technical Data Electrical Characteristics Rated voltage 100 V - 240 V Tolerance of the rated voltage +6 % / -10 % Rated frequency 50 Hz / 60 Hz Rated
Resumen del contenido incluido en la página 13
Introduction Technical Data Environmental Conditions (according to DIN EN 60721-3-x) Climate/operation (class 3K2): Temperature 15 °C to 35°C Relative humidity 5% to 85% altitude (NN) max. 3048 m (10000 ft.) Climate/transport (class 2K2): Temperature -25°C to 60°C Relative humidity 15% to 98% altitude (NN) max. 15240 m (50000 ft.) Mechanical environmental conditions Operation Class 3M2 Transport Class 2M1 Standards Complied With Product safety and ergonomics IEC 60950 (DIN EN 60950), UL 1950, C
Resumen del contenido incluido en la página 14
Resumen del contenido incluido en la página 15
2 Important Notes 2.1 Notes on Safety In this section you will find information that you must note when using the storage subsystem. This device complies with the relevant safety standards for IT equipment, including electronic office machines, intended for use in the office environment. I You will also find the following safety instructions in the manual entitled “Safety, Warranty and Ergonomics“ which also includes other notes on guarantee and ergonomics. Also pay attention to the notes i
Resumen del contenido incluido en la página 16
Notes on Safety Important Notes V CAUTION! Check that the rated voltage specified on the device's ID plate is the same as the local line voltage. The device must only be connected to a properly grounded wall outlet (the device is fitted with a tested and approved power cable). Make sure that the protective grounded outlet of the building’s wiring system is freely accessible. Switching off the device does not cut off the supply of power. To do this you must remove the power plugs.
Resumen del contenido incluido en la página 17
Important Notes Electrostatic Sensitive Device Label 2.2 Electrostatic Sensitive Device Label Electrostatic-sensitive components may be identified by the following sticker: Figure 1: Electrostatic Sensitive Device (ESD) sticker You must follow the instructions below when handling modules containing electrostatic-sensitive components Ê Discharge static electricity from your body (for example by touching a grounded metal object) before handling modules containing electrostatic- sensitive compone
Resumen del contenido incluido en la página 18
CE certificate Important Notes 2.3 CE certificate The shipped version of this device complies with the requirements of the EEC directives 89/336/EEC “Electromagnetic compatibility” and 73/23/EEC “Low voltage directive”. The device therefore qualifies for the CE certificate (CE=Communauté Européenne). 2.4 RFI Suppression All other equipment which is connected to this product must also have radio noise suppression in accordance with EC Guideline 89/336/EWG. Products which meet this requirement
Resumen del contenido incluido en la página 19
Important Notes Notes on the Rack Model 2.6 Notes on the Rack Model For safety reasons, at least two people are required to install the rack model because of its weight and size. When connecting and disconnecting cables, observe the notes in the documentation for your PRIMERGY system and the comments in the “Important notes” chapter in the technical manual supplied with the rack. Ensure that the anti-tilt bracket is correctly mounted when you set up the rack. For safety reasons, no m
Resumen del contenido incluido en la página 20
Environmental Protection Important Notes 2.8 Environmental Protection Environmentally friendly product design and development This product has been designed in accordance with the Fujitsu Siemens Computers standard for “environmentally friendly product design and devel- opment”. This means that the designers have taken into account important criteria such as durability, selection of materials and coding, emissions, packaging, the ease with which the product can be dismantled and the extent to
