Resumen del contenido incluido en la página 1
AW-PH360N
@
Indoor Pan/Tilt Head
AW-PH360N
Before attempting to connect, operate or adjust this product,
please read these instructions completely.
Printed in Japan
D
F0505Y0 VQTB0085
Resumen del contenido incluido en la página 2
O O O O 2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi
Resumen del contenido incluido en la página 3
FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses
Resumen del contenido incluido en la página 4
Contents Introduction ........................................... 4 Connections ........................................ 18 $ Connecting the connector panel .... 18 Accessories ........................................... 4 $ Head connector panel .................... 23 $ Connecting the base connector Installation precautions ........................ 5 rear panel and the base Precautions for use .............................. 6 connector front panel ................. 24 $ Connecting the AC adap
Resumen del contenido incluido en la página 5
Installation precautions ODo not install the pan/tilt head on any of its sides. OAvoid using the pan/tilt head in kitchens or other places where there is excessive steam and oil fumes. OMake sure that the installation of the pan/tilt head has been completed before mounting the camera onto it. OThis pan/tilt head has a maximum load capacity of 8.8 lb (4 kg). Do not use it for loads over 8.8 lb (4 kg). ODo not use a lens that will cause the camera to be poorly balanced. Such a lens should not be u
Resumen del contenido incluido en la página 6
Precautions for use OIn order to protect the environment when the pan/tilt head is to be discarded at the end of its service life, ask a specialized contractor to dispose of it properly. OThis pan/tilt head uses a manganese dioxide-lithium battery (CR2032). Be absolutely sure to remove this battery when disposing of the pan/tilt head or printed circuit boards. Be sure to dispose of any batteries removed according to the applicable regulations of the country concerned. Do not dispose of this type
Resumen del contenido incluido en la página 7
Parts and their functions - 7 -
Resumen del contenido incluido en la página 8
Parts and their functions 1Tilting arm ;Base This tilts in the vertical direction. Base connector rear panel These are used to maintain the This is used for connectio
Resumen del contenido incluido en la página 9
Installation (The installation work must be performed by your dealer without fail.) $ Assembling the pan/tilt head Be absolutely sure to hold the pan/tilt head by the base when handling it. OAttaching the tilting arm Use the tilting arm fixing screws to attach the tilting arm. The way in which the arm is mounted differs depending on the direction in which it is installed. (See the figure below.) Suspended installation Stand-alone installation Tilting Arm Tighten up the screws securely to
Resumen del contenido incluido en la página 10
Installation (The installation work must be performed by your dealer without fail.) $ Controller selection switch / installation direction switch / landing characteristics settings The following switches are set when determining controller selections, stand alone settings and landing characteristics settings. (RP501 / suspended installation / soft landing are the default settings.) 1. Remove the four head cover screws, and remove the cover slowly. (Take care not to disturb the tally LED lamp wir
Resumen del contenido incluido en la página 11
Installation (The installation work must be performed by your dealer without fail.) $ Transmission signal selection setting The switches on the COMP and CONNECTOR printed circuit boards must be set to correspond to the signals to be transmitted and components to be connected to the pan/tilt head. (When shipped, the analog settings are supported.) OAnalog/IEEE1394 card settings OWEB card settings SDI/PR switch: PR SDI/PR switch: PR WEB/1394 switch: 1394 WEB/1394 switch: WEB WEB/RP 422 switch: RP
Resumen del contenido incluido en la página 12
Installation (The installation work must be performed by your dealer without fail.) $ Setting the cable compensation circuit of video signals (COMP switch of the COMP printed circuit board is set to “OFF” in the default setting.) 1 When using the AW-RP501 controller or the AW-HB505 multiport hub (for transmissions using composite signals) When this controller (or multiport hub) has been connected to the pan/tilt head, it is permissible for the connecting cables to be up to 1640 ft. (500 m) long
Resumen del contenido incluido en la página 13
Installation (The installation work must be performed by your dealer without fail.) $ Installing the pan/tilt head Be absolutely sure to follow the instructions below when installing the pan/tilt head. Failure to do so may cause the pan/tilt head to slip out of position or fall. OFor wall Do not install the pan/tilt head on any of its sides. The wall should be capable of supporting a weight of at least four times the pan/tilt head with camera etc. weight 59.5 lb (27 kg). OMake sure that the inst
Resumen del contenido incluido en la página 14
Installation (The installation work must be performed by your dealer without fail.) $ Mounting the camera The pan/tilt head’s camera mounting section has a mechanism for maintaining the camera’s balance that moves the camera mounting plate using a guide roller as a fulcrum. Use the described recommended lenses corresponding to the camera to be used. (Before mounting a lens other than recommended lenses, consult with your dealer.) 1. Change the position of guide pin A and/or the camera mounting s
Resumen del contenido incluido en la página 15
Installation (The installation work must be performed by your dealer without fail.) • Stand-alone installation Adjust the balance by moving the camera mounting plate. or Adjust the balance by moving the camera mounting plate. or When the pan/tilt head is set at suspended installation, change the position of guide screws and guide pin B to adjust the balance as well as the stand-alone installation. <
Resumen del contenido incluido en la página 16
Installation (The installation work must be performed by your dealer without fail.) With the AW-E350/AW-E650 OAttaching the chain 1. Attach one end of the chain to the Chain attachment screw M4!6 mm or M2.6!6 mm: pan/tilt head using a chain attachment with flat washer/spring washer screw (M4!8 mm: with flat Chain washer/spring washer). 2. Position the other end of the chain over the screw hole on the top of the camera and attach it using a chain attachment screw (M4!6 mm: with flat Chain attachm
Resumen del contenido incluido en la página 17
Installation (The installation work must be performed by your dealer without fail.) OMounting a camera When mounting a camera to the pan/tilt head, take appropriate measures to prevent the camera from falling or being stolen. Camera guide pin 1. Place the camera on the camera mounting base and insert the guide pin into the guide hole on the camera. 2. Tighten the 2 camera mounting screws to fix the camera firmly in place. Camera mounting Screw 3. After mounting the camera, check that it is firm
Resumen del contenido incluido en la página 18
Connections $ Connecting the connector panel (with the controller AW-RP501) Convertible camera Zoom lens Head connector panel Camera cable (supplied) 10BASE-T (equivalent DC cable Control panel: to UTP category 5) (UL Type SPT-2 2!16 AW-RP501 straight cable AWG or UL Type NISPT-2 2!16 AWG, to be locally purchased) AC adapter: AW-PS505A AC adapter: AW-PS300A Coaxial cable Coaxial cable (BELDEN 8281) Monitor Base connector front panel Base connector rear panel - 18 -
Resumen del contenido incluido en la página 19
Connections $ Connecting the connector panel (with the controller AW-RP505) Convertible camera Zoom lens Camera cable (supplied) DC cable (UL Type SPT-2 2!16 AWG or UL Type NISPT-2 2!16 AWG, to be locally purchased) AC adapter: AW-PS300A 10BASE-T (equivalent to UTP category 5) straight cable Coaxial cable Base connector (BELDEN 8281) front panel Control panel: Multiport hub: AW-RP505 AW-HB505 AC adapter: AW-PS505A 10BASE-T (equivalent to UTP category 5) straight cable Coaxial cable (BELDEN 8281
Resumen del contenido incluido en la página 20
Connections $ Connecting the connector panel (with the controller AW-RP605A) Convertible camera Zoom lens Camera cable (supplied) DC cable (UL Type SPT-2 2!16 AWG or UL Type NISPT-2 10BASE-T (equivalent to UTP 2!16 AWG, to be locally category 5) straight cable purchased) AC adapter: AW-PS300A Coaxial cable (BELDEN 8281) Base connector front panel Multi-Function Controller: AW-RP605A Coaxial AC adapter: AW-PS505A cable Monitor - 20 -
