Resumen del contenido incluido en la página 1
Sim p lif y
Q
®
QLA 2310F/2310FL User’s Guide
2-Gb Fibre Channel to PCI-X Host Bus Adapters
FC2354603-00 A Page i
Resumen del contenido incluido en la página 2
QLA2310F/2310FL User’s Guide 2-Gb Fibre Channel to PCI-X Host Bus Adapters Q Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for i
Resumen del contenido incluido en la página 3
Table of Contents Section 1 Introduction 1.1 How to Use this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.2 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.3 What is Fibre Channel? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.4 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Section 2 QLA2310
Resumen del contenido incluido en la página 4
QLA2310F/2310FL User’s Guide 2-Gb Fibre Channel to PCI-X Host Bus Adapters Q Figures Figure Page 2-1 QLA2310F HBA Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 2-2 QLA2310FL HBA Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2-3 QLA2310F/2310FL HBA LED Activity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Tables Table Page 2-1 QLA2310F/2310FL Board Op
Resumen del contenido incluido en la página 5
Section 1 Introduction 1.1 How to Use this Guide The SANblade ™ QLogic host bus adapters (HBAs) supported in this document are described in the following paragraphs. They are collectively referred to as the QLA2310F/2310FL HBA unless otherwise noted. ® ■ QLA 2310F (single channel, full-height bracket, optical media) ® ■ QLA 2310FL (single channel, low-profile bracket, optical media) The QLA2310F/2310FL HBAs are 64-bit, 66-MHz PCI-X to Fibre Channel optical media. First, install the QLA
Resumen del contenido incluido en la página 6
1 – Introduction Features Q 500 meters at the data rate of 1 Gbps; less than 300 meters at the data rate of 2Gbps). With its increased connectivity and performance, Fibre Channel is the I/O technology preferred and used by system designers. 1.4 Features ■ Compliance with PCI Local Bus Specification revision 2.2 ■ Compliance with PCI-X Addendum (revision 1.0) to the PCI Local Bus Specification ■ Compliance with Third Generation Fibre Channel-Physical and Signaling Interface (FC-PH-3) standar
Resumen del contenido incluido en la página 7
Section 2 QLA2310F/2310FL 2.1 QLA2310F/2310FL HBA Components Figure 2-1 identifies the QLA2310F/2310FL HBA components referenced throughout this section. Each QLA2310F/2310FL HBA has a unique serial number; its location on the HBA is noted in figures 2-1 and 2-2. Take a minute to write down the serial number of the QLA2310F/2310FL HBA. SERIAL NUMBER J2 1 3 J1 ISP CHIP Figure 2-1. QLA2310F HBA Layout FC2354603-00 A 2-1 LED
Resumen del contenido incluido en la página 8
CONNECTOR 2 – QLA2310F/2310FL QLA2310F/2310FL HBA Components Q ISP CHIP J1 J2 1 3 NOTE: The serial number is on the other side of the HBA. Figure 2-2. QLA2310FL HBA Layout 2.1.1 LEDs Figure 2-3 identifies and describes the activity of the QLA2310F/2310FL HBA LEDs. Green LED Amber LED Activity Off Off Power off On On Power On Off Online Off On Link established Off Flashing twice per Loss of GREEN LED second synchronization AMBER LED Alternate flashing Alternate flashing Firmware error twice per
Resumen del contenido incluido en la página 9
2 – QLA2310F/2310FL Installation in the Computer Q 2.2 Installation in the Computer Perform the following steps to install the QLA2310F/2310FL HBA in your PC: 1. Check the motherboard and make any configuration changes necessary to accommodate the QLA2310F/2310FL HBA. The QLA2310F/2310FL HBA is self-configuring; however, some motherboards require manual configuration. For example, some systems have a PCI Device Configuration menu in the motherboard setup BIOS where you must enable HBAs, bus
Resumen del contenido incluido en la página 10
2 – QLA2310F/2310FL Installation in the Computer Q 7. Secure the QLA2310F/2310FL HBA to the chassis. Follow the PC manufacturer’s instructions. 8. Connect the appropriate cable from the devices to the corresponding connector. 9. Carefully reinstall the computer cover. Insert and tighten the computer cover screws. 10. Power up all external FC devices, then power up the PC and observe the monitor. The BIOS is disabled by default. Consequently, the devices attached to the QLA2310F/2310FL HBA ar
Resumen del contenido incluido en la página 11
2 – QLA2310F/2310FL Specifications Q 2.2.1 Installation Help If your system has an IDE hard disk, it may be assigned device number 80, which is the boot device. If your system does not have an IDE hard disk, a parallel SCSI host bus adapter (HBA), or a RAID adapter, the first bootable FC hard disk configured (the one with the lowest ID) is assigned device number 80 and becomes the boot device. The QLA2310F/2310FL HBA BIOS must be enabled if the boot device is connected to the QLA2310F/2310F
Resumen del contenido incluido en la página 12
2 – QLA2310F/2310FL Label Q Table 2-2. QLA2310F/2310FL Board Specifications (Continued) Type Specification Fibre Channel Bus type: Multimode fibre optic media specifications Bus transfer rate: 200 MBps maximum at half-duplex 400 MBps maximum at full-duplex Interface chip: ISP2310 CPU Single-chip design that includes a QLogic RISC processor, Fibre Channel protocol manager, PCI/PCI-X DMA controller, and integrated serializer/deserializer (SERDES) and electrical transceivers that can auto-negoti
Resumen del contenido incluido en la página 13
2 – QLA2310F/2310FL Agency Certification Q 2.5 Agency Certification 2.5.1 QLA2310F The following sections contain a summary of EMC/EMI test specifications performed on QLA2310F (FC2310401) to comply with radiated emission, radiated immunity and product safety standards. 2.5.1.1 EMI and EMC Requirements The QLA2310F conforms to the following requirements: ■ FCC Part 15, Class B ❑ Radiated Emission Class B ❑ Conducted Emission Class B ■ 89/336/EEC EMC Directive CE ❑ EN55022:1995 Class B ❑ Radiat
Resumen del contenido incluido en la página 14
2 – QLA2310F/2310FL Agency Certification Q 2.5.1.2 Product Safety Requirements ■ UL, cUL ❑ UL60950 ❑ CSA C22.2 No.60950 ❑ Class 1 Laser Product per DHHS 21CFR (J) ■ 73/23/EEC Low Voltage Directive ❑ TUV: ❑ EN60950:1992+A1,2,3,4,11 ❑ EN60825-1:1994+A11 ❑ EN60825-2:1994 2.5.2 QLA2310FL The following sections contain a summary of EMC/EMI test specifications performed on QLA2310FL (FC2310405) to comply with radiated emission, radiated immunity and product safety standards. 2.5.2.1 EMI and EMC Requ
Resumen del contenido incluido en la página 15
2 – QLA2310F/2310FL Agency Certification Q ❑ EN61000-3-2:1995 Harmonic Current Emission ❑ EN61000-3-3:1994 Voltage Fluctuation and Flicker ■ VCCI, Class B ■ CNS 13438 Class B BSMI ■ AS/NZS 3548 Class B ■ Korea MIC 2.5.2.2 Product Safety Requirements ■ UL, cUL ❑ UL1950 ❑ cUL C22.2 No.950 ❑ Class 1 Laser Product per DHHS 21CFR (J) ■ 73/23/EEC Low Voltage Directive ❑ TUV: ❑ EN60950:1992+A1,2,3,4,11 ❑ EN60825-1:1998+A1 ❑ EN60825-2:1994 FC2354603-00 A 2-9
Resumen del contenido incluido en la página 16
2 – QLA2310F/2310FL Agency Certification Q Notes 2-10 FC2354603-00 A
Resumen del contenido incluido en la página 17
Section 3 Troubleshooting 3.1 Problems After Installation There are three basic types of installation problems that can cause your QLA2310F/2310FL HBA to function incorrectly: hardware problems, system configuration problems, and Fibre Channel problems. The following section provides itemized checklists to help you determine why your QLA2310F/2310FL HBA is not functioning. 3.2 Hardware Problem Checklist ■ Are all of the circuit cards installed securely in the system? ■ Are all of the c
Resumen del contenido incluido en la página 18
3 – Troubleshooting System Configuration Problem Checklist Q 3.3 System Configuration Problem Checklist All PCI-compliant and PCI-X-compliant systems automatically detect 32-bit or 64-bit HBAs and set the appropriate bus speed (for example, 33 MHz or 133 MHz). Check the motherboard for proper configuration (see the appropriate installation section for more information. See the documentation supplied with your computer, or contact your computer dealer to determine if your motherboard requires
