Manual de instrucciones de American Standard SELECTRONIC Hard-Wired AC Powered ICU Lavatory Proximity Faucet 6059.193

Resumen del contenido incluido en la página 1

SELECTRONIC®
Hard-Wired AC Powered ICU
Lavatory Proximity Faucet
PRODUCT NUMBER
6059.193
Product No.'s & Options 1
Specifications 2
How to Install 2-3
Electrical Hook-up 4-5
6059.193 ICU Faucet shown Installed on
American Standard 9118.111 ICU Sink
Maintenance 6-7
FAQ,s 8
Replacement Parts 9
Certified to comply with ASME A112.18.1M
© 2012 American Standard
M965271
NOTE TO INSTALLER: Please give this manual to the customer after installation.
To learn more about American Standard Faucets visit our

Resumen del contenido incluido en la página 2

Base P r oduct Deck Plate Mixing Valve Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. All American Standard Faucets Are Water Tested At Our Factory. UNPACKING Some Residual Water May Remain In The Faucet During Shipping. 1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items a

Resumen del contenido incluido en la página 3

Roughing-in Dimensions FINISHED WALL GENERAL DESCRIPTION: (243mm) (127mm) 9-9/16" 5" Electronic faucet with proximity operation. Vandal resistant solid brass construction single post mounting. Operates on AC permanent power. In-line strainer for solenoid is integral. Single inlet (53mm) (133mm) 3/8 compression, built-in checks, and flexible 2-1/8" DIA. 5-1/4" MOUNTING stainless steel 16-1/4" reach inlet hose for spout SURFACE connection. 32mm Note: All plumbing and electrical wiring must

Resumen del contenido incluido en la página 4

MOUNT ENCL 2 OSURE; Fig. 2 Fig. 2 21" (533mm) NOTE. The illustration shows the ICU FAUCET mounted on the American Standard ICU Sink. Faucet can be installed on almost any sink or countertop. For Faucet installation on the American Standard ICU Sink, see instruction sheet No. 7301793-100 (ICU Sink System) 14" ENCLOSURE (356mm) MOUNTING supplied with Sink for more detailed information. HOLES 1. For installation on ICU Sink mount ENCLOSURE (1) 2-3/4" 2 (71mm) on MOUNTING BRACKET (2) with

Resumen del contenido incluido en la página 5

Fig. 1 4 1 ELECTRICAL INSTALLATION 5 1 ELECTRICAL CONNECTIONS; Fig. 1 Before opening ENCLOSURE CAUTION disconnect AC power supply. 1. Remove ENCLOSURE COVER (1). Fig. 1. 2. Feed the WIRE CONNECTORS (2) through the top of ENCLOSURE (5). Fig. 1a. 3. Remove GROMMET (4) from ENCLOSURE (5). Fig. 1. Fig. 1a Fig. 1b 4" 4. Feed the gray SENSOR WIRE (7) through GROMMET (4), 4" from CONNECTOR. Fig. 1b. Insert gray SENSOR WIRE (7) into SPLIT PLUG (9). Push 5 SPLIT PLUG (9) into GROMMET (4) to se

Resumen del contenido incluido en la página 6

Fig. 2 Unit #1 Unit #2 Unit #3 10 9 4 4 TW TWO PIECE O PIECE GR GROMMET OMMET 6 3 3 1 3 2 1 4" 1 1 1 5 FOR AC-VERSION 2 Fig. 3a (MULTI HOOK-UP); Fig. 2, 3 TW TWO PIECE O PIECE 1. See AC Version Electrical Hook-up for first unit of the GR GROMMET OMMET 8 Multi hook-up. 7 2. Remove ENCLOSURE COVERS from all ENCLOSURES. 3. Remove SOLID BLACK INSERT(1) from right side of ENCLOSURE #1 and replace with gray 2-PIECE GROMMET (3). Re

Resumen del contenido incluido en la página 7

Fig 1 TEST INSTALLED FAUCET TO ENSURE A LAMINAR WATER FLOW the air must be slowly purged from the spout. To do so, cover the SENSOR (1) while slowly opening the water supply valves. When the water flows as a solid, smooth, steady stream, uncover the SENSOR (1) and fully open the water supply valve. Fig. 1. MAINTENANCE 1 HOW TO CHANGE SENSOR RANGE; (Factory set at 6") Fig. 2 1 1. Setting the Detection Zone (Distance): Fig. 1. Detection Zone: 2" - 10" (50mm - 250mm) Default: Set at Fact

Resumen del contenido incluido en la página 8

HOW TO CLEAN AND REMOVE 4 Fig.4 3 THE FLOW RESTRICTOR; Fig. 4 1 REMOVE SET SCREW (1) 1. Remove SET SCREW (1) with FLAT BLADE 2 SCREWDRIVER (2). Pull off SPOUT (3) from faucet base. Fig. 4 & 4a. 2. Remove HOUSING (4) and remove FLOW RESTRICTOR (5). Fig. 4b. 3. Rinse clean FLOW RESTRICTOR (5). Reassemble and install into SPOUT BASE (6). Reassemble SPOUT (3) onto SPOUT BASE (6) and tighten SET SCREW (1). Fig. 4. Fig.4a Fig.4b 4 5 3 PULL UP TO REMOVE SPOUT 4 6 GENERAL CLEANING; Fig. 5 5 Fig.

Resumen del contenido incluido en la página 9

FAQ'S Q: How will I know if battery needs to be replaced? Q: Why does the faucet operate the opposite of A: Valve does not open and sensor blinks 2 times expected-Turns On when not in sensor range, but turns interrupted by pause for up to 7 days. off when in sensor range? A: Sensor wires to solenoid are reversed. Black to - Q: Why has the flow rate of the faucet reduced & Red to + is correct. significantly? A: Check and clean aerator and strainer. Q: What is the normal operating pressur