Resumen del contenido incluido en la página 1
™
SilverStar
SILVER BOOM 300
www.silverstarlifts.com www.pridemobility.com
Resumen del contenido incluido en la página 2
SAFETY GUIDELINES WARNING! An authorized Pride Provider or qualified technician must perform the initial setup of this lift and must perform all of the instructions in this manual. The symbols below are used throughout this owner's manual and on the product to identify warnings and important information. It is very important for you to read them and understand them completely. WARNING! Indicates a potentially hazardous condition/situation. Failure to follow designated procedures can cause either
Resumen del contenido incluido en la página 3
CONTENTS I. INTRODUCTION......................................................................................................................... 4 II. SAFETY ......................................................................................................................................... 5 III. INSTALLATION .......................................................................................................................... 8 IV. OPERATION ............................................
Resumen del contenido incluido en la página 4
I. INTRODUCTION Welcome to Pride Mobility Products Corporation (Pride). Congratulations on the purchase of your new SilverBoom. The SilverBoom design combines the most advanced state-of-the-art components with modern, attractive styling. We are certain that the design features and trouble-free operation will add convenience to your daily living and ensure complete satisfaction. At Pride, your safety is important to us. Please read and follow all instructions in this manual before operat- ing yo
Resumen del contenido incluido en la página 5
II. SAFETY PRODUCT SAFETY SYMBOLS The symbols below are used on the lift system to identify warnings, mandatory actions, and prohibited actions. It is very important for you to read and understand them completely. Read and follow the information in the owner’s manual. Do not sit on mobility product while operating the lift system or during transport. Do not lift people. Maximum lifting capacity. Pinch/Crush points created during assembly and/or operation. Do not lift pets. Do not extend the lift
Resumen del contenido incluido en la página 6
II. SAFETY Avoid exposure to rain, snow, ice, salt, or standing water whenever possible. Maintain and store in a clean and dry condition. Only authorized personnel may service this equipment. Disposal and recycling-Contact your authorized Pride Provider for information on proper disposal of your Pride product and its packaging. Disposal and recycling-Contact your authorized Pride Provider for information on proper disposal of your Pride product and its packaging. 6
Resumen del contenido incluido en la página 7
II. SAFETY LIFTING CAPABILITIES The SilverBoom 300 is designed to lift a maximum weight of 300 lbs. (136 kg). Under no circumstances should the SilverBoom be made to exceed this weight limit. Subjecting the SilverBoom to the strain of lifting more than it is designed to, may cause it to fail, resulting in damage to the mobility product and/or injury to the lift operator. Refer to the mobility product owner’s manual for information on the overall weight of the mobility product before lifting
Resumen del contenido incluido en la página 8
III. INSTALLATION The SilverBoom can be installed in either side of your vehicle. The illustrations demonstrate installation on the SCREWS right side. SCREWS POWER ROTATING BASE SHROUD RE- MOVAL Installing a power rotating base requires that the base shroud be removed in order to access the rear mounting holes of the L-base. See figure 1. 1. Remove the 4 screws that secure the shroud to the base. 2. Carefully lift the shroud up and off of the base. Figure 1. Power Rotating Base Shroud Removal N
Resumen del contenido incluido en la página 9
! III. INST ALLA TION TRUNK INSTALLATION (SILVERBOOM 300 MANUAL ROTATION ONLY) WHEEL WELL Position the L-base as shown in figure 3. You may need to situate the L-base so the wheel well does not interfere with the L-base extensions. Ensure there is adequate room for a mobility product to comfortably fit into the trunk. ASSEMBLING THE LIFT 1. Insert the upper post into the L-base. See figure 5. NOTE: When inserting the upper post into a power rotating base, a slight adjustment of the sprocket may
Resumen del contenido incluido en la página 10
III. INST ALLA TION 3. Lower the motor housing over the upper post until it rests on the height adjustment ring. See figure 7. WARNING! Pinch Point Hazard! Keep hands clear of the upper post when lowering the motor housing. WARNING! The lift will be top heavy until mounted securely. Get assistance to help stabilize the lift while swinging the boom-arm. HATCHBACK INSTALLATION- MINIVANS, STATION WAGONS, ETC. Once the lift is assembled and seated on the L-base, close the hatch slowly to make sure i
Resumen del contenido incluido en la página 11
III. INST ALLA TION BOOM-ARM ADJUSTMENT Before adjusting the boom-arm, lower the lifting hook BOW TIE COTTER PIN about 12 in. (30.5 cm). This will provide enough slack in the strap to enable the adjustable portion of the boom- arm (top tube) to be pulled out of the bottom tube to its TOP TUBE ADJUSTMENT HOLES farthest adjustment hole. See figure 9. To adjust the boom-arm: BOTTOM TUBE 1. Remove the bow tie cotter pin from the adjustment pin and remove the adjustment pin. LIFTING HOOK 2. Slide the
Resumen del contenido incluido en la página 12
III. INSTALLATION NOTE: Choosing the correct length bolt allows enough bolt-thread to pass through the undercarriage, ensuring enough room for the mounting washer and nut to be installed securely. 6. From under the vehicle, install the mounting washers and nuts to all five (5) mounting bolts and tighten. See figure 10. NOTE: The holes in the mounting washers are for working around obstructions. Choose the hole that best works in the area you are installing the mounting bolts. 7. Place the L-base
Resumen del contenido incluido en la página 13
III. INST ALLA TION PHILLIPS HEAD SCREW 10 MM L-BASE CAP MOTOR HOUSING UPPER POST L-BASE CAP L-BASE T-BAR Figure 11. L-Base Cap Installation Figure 12. Fully Assembled Lift (SilverBoom 300 Shown) ELECTRICAL WIRING INSTALLATION 1. Route the lift’s long power wire (starting at the lift) through the interior of the vehicle until you reach the automobile battery. See figure 13 and 13A. Conceal the wire behind or under the interior panels (there should be existing holes). Be certain that the wire is
Resumen del contenido incluido en la página 14
III. INST ALLA TION MOTOR HOUSING ROUTE BLACK (-) GROUND WIRE TO NEGATIVE (-) BATTERY TERMINAL ROUTE RED (+) POWER WIRE TO POSITIVE (+) BATTERY TERMINAL FUSE 25-AMP CRIMP HERE AUTOMOBILE BATTERY Figure 13. SilverBoom 300 Electrical Wiring Connections MOTOR HOUSING UPPER POSTCAP ROUTE BLACK (-) GROUND WIRE TO NEGATIVE (-) BATTERY TERMINAL ROUTE RED (+) POWER WIRE TO POWER POSITIVE (+) BATTERY TERMINAL ROTATING BASE FUSE 25-AMP CRIMP HERE AUTOMOBILE BATTERY Figure 13A. SilverBoom 300 With Power Ro
Resumen del contenido incluido en la página 15
IV. OPERATION PROHIBITED! Avoid exposure to rain, snow, ice, salt, or standing water whenever possible. Maintain and store in a clean and dry condition. PRESS TO OPERATE LIFTING STRAP IN A DOWNWARD HAND/REMOTE CONTROL OPERATION DIRECTION Hand Control The hand control for the SilverBoom 300 operates the lift- PRESS TO OPERATE ing strap in two directions, up and down. See figure 14. LIFTING STRAP IN AN UPWARD DIRECTION Power Rotating Base The hand control for the SilverBoom 300 power rotat- ing b
Resumen del contenido incluido en la página 16
IV. OPERATION Remote Control Battery Replacement As with all electronic devices powered by batteries, the battery of the remote control will eventually need to be DOCKING DEVICE T-BAR replaced. When the lift responds intermittently or no longer responds to the commands from the remote control, replace the battery. To replace the batteries of the remote control: LIFTING HOOK 1. Loosen and remove the screws from the back of the remote control. 2. Remove the old battery. The battery slides in and o
Resumen del contenido incluido en la página 17
IV. OPERATION WARNING! Pinch/Crush Hazard! Always keep hands clear of the lifting strap while the SilverBoom is lifting/ lowering a mobility product. The operator of the lift should stand a safe distance away from the mobility product being lifted/lowered to ensure that feet are never positioned under a raised mobility product. Do not drag the mobility product into position using the lift. If dragging occurs, your mobility product is too far away from the vehicle. To prevent dragging: " Release
Resumen del contenido incluido en la página 18
IV. OPERATION 12. Disconnect the power to the SilverBoom to prevent any accidental movement when transporting your mobility product. WARNING! Your SilverBoom was designed to be mounted primarily in a motor vehicle. Mounting your SilverBoom on a platform, where the height of the lift may cause the lifting strap to extend beyond a safe point, can damage the SilverBoom and injure the lift operator. MANUAL LIFT STRAP OPERATION The SilverBoom 300 with a power rotating base is equipped with a lift
Resumen del contenido incluido en la página 19
V. T R OUBLESHOOTING LIFT WILL NOT OPERATE CIRCUIT BREAKER RESET BUTTON " Check the circuit breaker reset button. Reset if nec- essary. See figures 21 and 22. " Ensure all harness connections are secure. " Ensure the power wire leading to the positive battery terminal is tight and not corroded. " Check the fuse located on the red power wire near the battery. If blown, replace with a new 25-amp fuse. See figure 23. WARNING! Do not use a higher rated fuse than 25-amp. Doing so may damage the lift’
Resumen del contenido incluido en la página 20
V. T R OUBLESHOOTING LIFTING STRAP TRAVELS IN OPPOSITE DIRECTION OF BUTTON BEING PUSHED ON HAND CONTROL Before each use, check that the lifting strap is traveling in the proper direction. If the belt travels in the wrong direction when you press either the up or down button, you must restore proper lifting strap travel. To restore proper lifting strap travel: 1. Pull slightly on the strap and operate the lift until the strap is extended completely past the “stop” warning label. 2. Allow the stra
