Resumen del contenido incluido en la página 1
PRN608-S
User Manual
Thermal printer controller
PRN608-S
FOR FUJITSU THERMAL PRINTERS
FTP608 SERIES
28-03-2003 Page 1-1 of 53
Resumen del contenido incluido en la página 2
PRN608-S VERSION HISTORY Version Date Init Status Description 1.0 030328 BB Released First release Copyright 1999-2003 by I/F-COM A/S. All rights reserved. I/F-COM A/S has prepared this manual for use by I/F-COM A/S’ customers. The information contained herein is the property of I/F-COM A/S and shall not be reproduced in whole or in part without the prior written approval of I/F-COM A/S. I/F-COM A/S reserves the right to make changes without notice to the spec
Resumen del contenido incluido en la página 3
PRN608-S completely excluded. Please assume that such failure may occur before using this printer. We would urge that these specifications should be thoroughly understood and the printer used safely in your company or associated organisation. Please indicate or describe in your products and in the user manuals those items, which are related to the prevention or avoidance of danger and draw these to the attention of the eventual client (the user). 28-03-2003 Page 1-3 of 53
Resumen del contenido incluido en la página 4
PRN608-S 1 SYSTEM DESCRIPTION ............................................................................................1-7 2 INSTALLATION...........................................................................................................2-7 2.1 UNPACKING ..............................................................................................................2-7 2.2 LABELS.........................................................................................................
Resumen del contenido incluido en la página 5
PRN608-S 3.8.18 Italic off..........................................................................................................3-24 3.8.19 Italic on ..........................................................................................................3-24 3.8.20 Initialise Printer.............................................................................................3-24 3.8.21 Request Software version ............................................................................
Resumen del contenido incluido en la página 6
PRN608-S 7.2.1 Escape sequences, overview...........................................................................7-45 7.3 APS COMPATIBLE COMMAND SET (OPTIONAL) .......................................................7-48 7.3.1 Escape sequences, overview...........................................................................7-48 7.4 ESC/POS COMPATIBLE COMMAND SET (OPTIONAL)...............................................7-50 7.4.1 Escape sequences, overview...............................
Resumen del contenido incluido en la página 7
PRN608-S 1 SYSTEM DESCRIPTION This reference manual describes the specifications, functions, and operating procedures for the PRN608-S Interface Board. The PRN608-S is an interface board for the FTP608 series printer mechanisms. This reference manual also describes the print operation of the FTP608 series. Read this reference manual thoroughly before using the PRN608-S. PRN608-S is designed for the following Fujitsu printers: FTP-628MCLxxx FTP-638MCLxxx PRN608-S consists of
Resumen del contenido incluido en la página 8
PRN608-S thermal printer connector on the PCB. 1 Mounting hole is grounded. See drawing for more details. (a) To connect or remove the connector, always turn off the power in advance. If the connector is connected or removed while the power to the printer is on, errors may occur. (b) The connector of each cable must be correctly locked and connected. The connector at the head side has no lock feature. Check that the connector at the head side is completely inserted. (c) To insta
Resumen del contenido incluido en la página 9
PRN608-S even when setup menus can be set to higher speed. In order to obtain rd higher speed you need to install 3 part utility program on PC. Please visit www.if-com.com for further information. 1. Turn off power 2. Press Key 1 low while power up. Board is now in setting mode. Text will be printed on paper for further information 3. By activating key 1 and 2 you can change following parameters: a. Test printout b. Select Command set i. I/F-COM command set (Default) ii. Seiko comp
Resumen del contenido incluido en la página 10
PRN608-S 1. Input key (Default) 2. LED output 3. Label detect 4. Black mark detection 5. Paper near end function j. Key 2 function 1. Input key 2. LED output 3. Label detect 4. Black mark detection 5. Paper near end function k. IRDA i. Enabled (Optional) ii. Disabled l. Auto form feed i. 0 sec. ii. 1 sec. iii. 2 sec. (Default) iv. 3 sec. v. 4 sec. vi. 5 sec. m. Form feed length i. 0 mm ii. 1 mm iii. 2 mm iv. 5 mm v. 10 mm vi. 20 mm vii. 30 mm viii. 50 mm (Default)
Resumen del contenido incluido en la página 11
PRN608-S i. 0 (Default) ii. 1 iii. 2 iv. 3 v. 4 vi. 5 vii. 6 viii. 7 ix. 8 x. 9 r. Burn strobe light i. -1 ii. -2 iii. -3 iv. -4 v. -5 vi. -6 vii. -7 viii. -8 ix. -9 Settings will be effective upon turn off and on. * FTP628MCL00x/30x must be set as 384 dots. * FTP6x8MCL05x/1xx and FTP6x8MCL35x is auto detected. 2.6 Serial Input/Output If BUSY control is selected: When 236 bytes of data have been stored in the input buffer, the SBUSY signal becomes high to request
Resumen del contenido incluido en la página 12
PRN608-S When the error is cancelled, Xon is output. 2.6.1 Serial data transfer The PRN608-Stransfers various data other than the Xon and Xoff codes which are output when controlling Xon and Xoff. Regardless of whether the input mode is serial or parallel, the following data is transferred through the TxD terminal. (a) Error codes when a hardware error occurs at initialisation (b) The data when executing the Vhead voltage response (c) The data when the error status response is set an
Resumen del contenido incluido en la página 13
PRN608-S Error processing when receiving serial data The PRN608-S receives and checks serial data according to the transmission conditions. When the PRN608-S has received one byte of data without errors, the data is stored in the input buffer. If there are any errors, the following data is stored in the input buffer according to the type of error. Error type Error code Parity error (!: 21 ) 16 Framing error (?: 3F ) 16 If the input data cannot be printed correctly and instead “!” or “
Resumen del contenido incluido en la página 14
PRN608-S dot line so that the number does not exceed the specified maximum number of activated dots. The PRN608-S determines logical blocks each time it prints a single dot line. In dynamic division, in order to avoid unclear printing, at the first step of the motor the thermal head is driven and at the second step the paper is fed. Also, since the order of the printing blocks and printing speed are changed in each dot line according to the content of the print data, print quality may b
Resumen del contenido incluido en la página 15
PRN608-S Electrolytic corrosion may significantly shorten the life of the thermal head. Thermal paper ordinarily contains electrolytic material to prevent sheets from sticking to each other due to static electricity. If there is too much of this electrolytic material, high temperatures and humidity cause the material to ionise, resulting in electrolytic corrosion of the thermal head. The PRN608-S turns the FET off and breaks the Vhead applied to the thermal head during waiting status t
Resumen del contenido incluido en la página 16
PRN608-S Specifications Default settings Interface Serial RS232C, USB or IRDA 115.200 baud, 8 data bit, none parity, 1 stop bit, hardware Data format serial handshake. Baud rate can be changed by software. USB Printer class specification. Data format USB http://www.usb.org/developers/data/devclass/usbprint11.pdf IRDA (Ircomm specifications) Data format IRDA http://www.irda.org/standards/pubs/ircomm10.pdf Command set I/F-com Transmission to host Requested status etc. Printer sup
Resumen del contenido incluido en la página 17
PRN608-S 3 Function 3.1 General Notice, when data is sent from the external equipment to the printer controller, all data has to be sent as binary file. If data is being sent as a character file, and some data in the file is equal to EOF, the rest will not be received. 3.2 Serial communication. Standard communication is; Baud rate; 115.200 Baud Data bits = 8 Stop bits = 1. Parity = None Flow control = Hardware handshake Baud rate can be changed by a software command or by ent
Resumen del contenido incluido en la página 18
PRN608-S 3.5 Firmware upgrade. If firmware needs to be changed, alternative firmware can be downloaded. Please contact I/F-COM for firmware upgrade or changes. The steps to download an alternative firmware in DOS are the following. These steps only work for a serial connection, look further down how to do it with USB. 1. Power the system off. 2. Disconnect printer. 3. Short circuit the pins “upgrade firmware” 4. Turn on printer 5. Write the following command “mode com1:9600,n,8,1
Resumen del contenido incluido en la página 19
PRN608-S 3.7 Character design The following figures describes the design of different types of characters (small): 3.7.1 Normal Character. 3.7.2 Low Character
Resumen del contenido incluido en la página 20
PRN608-S 3.7.4 Bold When bold characters are printed the character is or with itself shifted right. 3.7.5 Reverse When reverse characters are printed the character matrix will be negated. 3.7.6 Italic. When Italic characters are printed every line will be shifted the following number of dots to the right: (Line number from bottom)/4 3.7.7 Font sizes. Font Width Height Small Normal Normal Low Double Normal Narrow Normal Double Normal Double Double Wide Double Quadruple High
