Resumen del contenido incluido en la página 1
Model APS-875
Owner’s Manual
4 Button Remote Start Security System With
Plug-In Shock Sensor & Starter Disable
IMPORTANT ! In order to provide you with the highest level of security to your
vehicle, this system is equipped with selectable manual override circuitry. It is
possible that you will need to override you security system if the transmitter
becomes lost, or inoperative due to battery failure. Reading the sections on
"Manually Overriding Your System" is necessary to fully understand t
Resumen del contenido incluido en la página 2
w Intrusion Alert With Memory w Instant Siren Activation w Starter Disable Output w Additional Engine Immobilizer Output, (Optional Relay Required) w True Last Door Arming (Hardwire Only) w Defective Zone By-Pass w Defective Zone Chirp Confirmation (Unit Chirps To Report Zone Cleared) w 6 Tone Mini Siren (New AS-9903) w Car Horn Output For Additional Alarm Response (Improved Timing To Minimize RF Interference.) w Additional Negative Trigger Input (Hood & Trunk) w RF Inhibit With Ignition On w Pa
Resumen del contenido incluido en la página 3
YOUR “ANTI CODE GRABBING“ TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automo- tive security system. Some of today’s sophisticated auto thieves use a device known as a code grabber, which will receive and store the signal from your key- chain transmitter, and re transmit at a later time to disarm your system. Your Keeloq Code Hopping transmitters will change their signal every t
Resumen del contenido incluido en la página 4
2. Press and hold button the Lock/Arm button on the keychain transmitter for 2 seconds. þ The dash mounted LED begins to flash slowly. þ Parking Lights flash one time. þ Siren will not sound. If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar. Simply close the opened entry point to provide full protection o Doors Lock - Optional Note: If the optional Headlamp illumination feature has been added, and has been selected for operation when arming, as an added convenienc
Resumen del contenido incluido en la página 5
drain, even when left unattended for extended periods. þ Whenever the system is triggered, the vehicle’s parking lights will flash for the full 30 second alarm cycle, attracting visual attention to the vehicle. þ Optional - Whenever the system is armed, the vehicle’s starting circuit will be bypassed. If the thief should choose to ignore the siren, the vehicle can not be started. þ Any mild impact to the vehicle’s glass will cause the alarm to sound a short series of warning tones. þ Any strong
Resumen del contenido incluido en la página 6
SILENT DISARMING (Must be activated during programming) Note: If the optional 2 step door unlock circuit is installed, when the unlock transmitter button is activated, the drivers door only will unlock, pressing the unlock button a second time will cause all doors to unlock. Note: If your transmitter has been configured with single button Lock/Unlock as shown, to activate the all door unlock feature operate the Lock/Unlock button a second time within 3 seconds of the first unlock command. 1. Pre
Resumen del contenido incluido en la página 7
device that may have been added to the system. If the LED is flashing two times...pause...two times...pause...etc., then an intrusion attempt was made to a hood or trunk pin switch that was added to the system, or to a light activated entry point if the alarm was installed using the voltage sensing feature. If the LED is flashing three times...pause...three times...pause...etc., then an intrusion attempt was made through one of the vehicle’s doors. These intrusion warning indicators are stor
Resumen del contenido incluido en la página 8
the consumer to program a personal override code, offering a higher level of security. To take advantage of this option, programmable feature # 10 must be selected for the Custom Code Option. Consult your installation center for programming details. The system comes from the factory with a pre-programmed override code of 11. To change this default override code, do the following: 1. Disarm the system by use of the transmitter, or by use of the emergency override sequence. Turn the ignition
Resumen del contenido incluido en la página 9
7. Within 10 seconds, begin to press and release the pushbutton switch to set the units digit. (As per the example, press and release 2 times to set the units digit to 2). 8. Turn the ignition switch to the off position. Immediately observe the LED flash pattern. You will note the LED flashing five times, pause, and then flash two times, pause. This pattern will be repeated three times indicating the new code (52) has been accepted and stored in memory. NOTE: If after step 7, the LED flashes a
Resumen del contenido incluido en la página 10
NOTE: Whenever the chirps are bypassed, the 4-chirp intrusion indicator and 3 chirp defective zone indicator will always operate. Since these are important warnings to you that something has happened, they cannot be eliminated. REMOTE PANIC OPERATION The Lock or Unlock button on your keychain transmitter also functions as a panic switch for use in emergency situations. To use remote panic, 1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or more seconds. The alarm wi
Resumen del contenido incluido en la página 11
The full detect trigger duration will be reduced from 30 seconds to 15 seconds. NOTE: Setting the stage of the shock sensor will be effective for one arming cycle only. Once the system has been disarmed, the very next arming cycle will cause the sensor to default to the normal operation stage. To change or adjust the shock sensor, press and release the ARM button of you keychain transmitter. 1. Within 2 seconds of arming, press and release the ARM button 1 time, to defeat the pre-detect stage
Resumen del contenido incluido en la página 12
WARNING! Be certain that the vehicle is outdoors before using this or any remote vehicle starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if it is garaged. To Remote Start The Vehicle: Press and release the programmed channel of your keychain transmitter two times within 2 seconds. The vehicle will start and remain running for the pre- programmed 5, 10, 15, or 20 minutes. A
Resumen del contenido incluido en la página 13
OPERATING ON AUTOMATIC START UP TIMER MODE The APS-875 has the ability to automatically start the vehicle every 2 or 4 hours over a 48 hour period. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. CAUTION! Be certain that the vehicle is outdoors before using this or any remote vehicle starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if pr
Resumen del contenido incluido en la página 14
ate transmitter button is depressed for 4 seconds. Optional devices that may be connected to this channel are; o Remote Electric Trunk Release o Remote Car Starter o Remote Window Closure o Remote Garage Door Interface NOTE: In addition there may be a second optional feature connected to your system that when the same transmitter button is pressed and released 2 times within 3 seconds (double pressed), the second optional feature will activate. This out- put is typically used for a remote star
Resumen del contenido incluido en la página 15
o Remote Window Closure o Remote Garage Door Interface To remotely operate the device indicated, momentarily press, or press and hold the appropriate transmitter button(s) as indicated above. ADDITIONAL REMOTE FUNCTION ( CHANNEL 6 ) Channel 6 is an alternate output that can be controlled by the unlock button of the transmitter, or by and independent button or combination of buttons. For your ve- hicle this output is Controlled By: o Trunk/Key Button o Option Button o Lock + Unlock Buttons o Lo
Resumen del contenido incluido en la página 16
APS 875 SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING/ACTIVE REARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH...PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 SIREN CHIRP INDICATORS 1 CHIRP * = ARM 2 CHIRPS * = DISARM 3 CHIRPS = ARM / DOOR OPENED 4 CHIRPS = DISARM / INTRUSION * These chirps are optional, and can be de - activated. PARKING LAMP INDICATORS 1 FLASH = ARM 2 FLASHES = DISARM
