Resumen del contenido incluido en la página 1
Model APS-905
Installation Manual
3 Channel Remote Start / Keyless Entry System
Installation Instructions
This Unit Is Intended For Installation In Vehicles With
12 Volt Negative Ground Electrical Systems,
Gasoline or Diesel With True Tach Reference
And Automatic Transmissions Only.
Kit Contents
(1) Control Module
(1) 5 Button One Way Flashlight Transmitter
(1) 5 Button Two Way Dot Matrix Transceiver
(1) On Glass Mount Superheterodyne Transceiver
(1) Multi Pin Input/Output Harness
(1) Six Pi
Resumen del contenido incluido en la página 2
Page 2 128-7410 2 of 20 SELECTABLE FEATURES The selectable features can be set manually as explained below, or with the RF feature programmer. To set features using the RF programmer, follow the instructions packaged with the programmer. Factory default settings are indicated by bold text. Note : The method of manual override can either be selected to operate from the valet switch or operate as custom code. Be certain to place a check mark indicating the method used in the box located on the las
Resumen del contenido incluido en la página 3
To program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Short chirp, then long chirp This Action Accesses Feature Bank 2 Alarm Selectable Features First Press and release the valet switch 1 chirp = 1 second door lock & unlock Press transmitter Lock button to change 2 chirps = 3.5 second door lock & Unlock Press transmitter Lock button to change 3 chirps =
Resumen del contenido incluido en la página 4
Page 4 128-7410 4 of 20 To exit program mode, turn ignition off, or press and release valet switch. RF Programmable Features Bank 3 Is Remote Start Selectable Features: To program these selectable features; Turn ignition on No response Press and release the program switch 3 times 1 flash Within 3 seconds, turn ignition Off Then On, Off then On This Action Accesses Feature Bank 3 Remote Start Selectable Features Press transmitter lock button to change or Press and release the program switch Feat
Resumen del contenido incluido en la página 5
Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then 2 long chirps This Action Accesses Feature Bank 3 Remote Start Selectable Features First Press the valet switch one time Not Available on this model Press transmitter Lock button to change Not Available on this model or Second Press and release the valet switch Not Available on this model Press transmitter Lock but
Resumen del contenido incluido en la página 6
This Remote Start/Keyless Entry System is designed for use with Automatic Transmission Vehicles Only! The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire is not connected, then the unit will remain in the Gasoline mode setting, which will crank the car when the RF signal is received with no delay. Regardless of the vehicle, Gasoline or Diesel, for every installation, the vehicle MUST HAVE a Tach Signal Input, and an Automat
Resumen del contenido incluido en la página 7
THE TRANSCEIVER/ANTENNA ASSEMBLY: The Superheterodyne Transceiver Antenna Assembly provided with this unit allows routing from below the dash- board for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception. Special considerations must be made for windshield glass as some newer vehicles utilize a metallic shielded window glass that will inhibit or restrict RF reception. In these vehicles, route the antenna toward a rear window location fo
Resumen del contenido incluido en la página 8
Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal injury and property damage. SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS. BLUE WIRE: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key is turned to the to the "ON" or "RUN" and the "START" or CRANK" positions and will have 0 volts when the key is turned to the "OFF" and "ACCESSORY" positions. For
Resumen del contenido incluido en la página 9
on + 12 volt source which will supply + 12 volt power to the additional ignition output, (Pink), wire. PINK Wire: Additional Ignition Output This wire can be used as an additional + 12 Volt ignition output supplied by the Red/Black wire. This output can be selected to be on or off during the start cycle. (See feature bank 3 selection # 8) Connect this wire to the third ignition circuit in the vehicle and set the selectable feature # 8 of Bank 3 according to the way in which the vehicle's igni
Resumen del contenido incluido en la página 10
If the vehicle has a factory installed hood pin switch and that switch provides + 12 Volts to an under hood light, the Brown wire can be connected to the existing pin switch. BROWN w/ BLACK Tracer Wire: Positive Inhibit Input 2 Any time + 12 Volts is applied to the Brown w/ Black tracer wire, the Remote Starter will stop operating, even if the signal is received from the transmitter. If the brake light switch in the vehicle switches + 12 Volts to the brake light circuit, connect the Brown w/ Bla
Resumen del contenido incluido en la página 11
LIGHT BLUE Wire: Ground Output While Running. This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes, and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off. In all of the applications described below, a relay will be required. The Light Blue wire can be used to accommodate the following situations: A. Shock Sensor By Pass: If there is Shock Sensor used with an alarm system and it is not shu
Resumen del contenido incluido en la página 12
Green/Orange Wire: Tach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil. This Remote Start unit learns the tach rate of the vehicle and in most cases will operate properly from one multi coil pack regardless of the number of cylinders. If the vehicle has a s
Resumen del contenido incluido en la página 13
NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement is more than 300 mA. 2 Pin Door Lock/Unlock Harness: (White Connector) The Red & Green Door Lock/Unlock output wires provide either a pulsed ground or pulsed + 12 volts to control the vehicle door lock / unlock circuits. The output of these wires has a maximum switching capability of 300mA. Many vehicles today have factory door lock relays which can be connected directly to these outputs
Resumen del contenido incluido en la página 14
Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt Door Lock Control Circuits These applications require the use of additional components which may include relays, fixed resistors, or for convenience, the AS 9159 Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supplement and or the Audiovox fax back service for information on your particular vehicle for properly connecting to these types of circuits. 2 Pin Red Connector: Control Switch Route the b
Resumen del contenido incluido en la página 15
3. Diagnostics: 1. Enter Bank 3 and turn on selectable feature # 9 as described on the front pages of this manual. 2. Press and hold the program push-button switch on, then turn the ignition key to the "ON" position. 3. The lights will flash and the number of flashes will indicate the reason for shutdown on the last remote start attempt. The indications are as follows. 1 Flash 5, 10, 15, or 20, minute run timer expired. 2 Flashes Low or No tach signal received. 3 Flashes Positive or Negative
Resumen del contenido incluido en la página 16
MANUAL SHUT DOWN / ENABLE CIRCUIT: The intent of the manual shut down / enable circuit is to allow the vehicle operator to prevent operation of the Remote Start Unit regardless of the RF transmitter operation. To test the integrity of the manual shut down / enable circuit: 1. Place the control switch in the on (Closed To Ground) position. 2. Start the vehicle using the RF transmitter. 3. The vehicle should start and run under the control of the remote start unit. 4. Move the switch to the off (O
Resumen del contenido incluido en la página 17
addition of a 4000 series diode. Shown is a typical GM Park/Neutral ECM input circuit. To connect the Audiovox remote start unit to the GM Park / Neutral ECM input: 1. Locate the Orange / Black reference wire in the "C2" connector found at the ECM in GM B Body vehicles or, locate the equivalent reference wire in the vehicle you are installing the Audiovox Remote Start Unit in. 2. Connect the Cathode, (Striped) end, of a 4000 series diode to this reference wire. 3. Connect the Anode, (Non S
Resumen del contenido incluido en la página 18
F. Connect terminal #86 of the relay to a fused +12 volt constant battery source. G. Connect terminal #87 of the relay to the Chime Module side of the previously cut wire in step D. H. Connect terminal #85 of the relay to the Drivers Door side of the pin switch wire previously cut in step B. METHOD 1 NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. The anode
Resumen del contenido incluido en la página 19
AFTER THE CONNECTION OF THE NEUTRAL START SAFETY WIRE AS INDICATED IN ANY OF THE PREVIOUS ALTERNATE CONFIGURATIONS, THIS CIRCUIT MUST BE TESTED FOR OPERATION. Retest by following the steps outlined in the NEUTRAL START SAFETY TEST shown in this manual. 4 Pin Upgrade Telematic Module: Red = + 5 Volts, Black = Ground, White = Data TX, Yellow = Data RX If used, connect the 4 pin harness from the Telematic one way module kit to the mating port on the controlling circuit. NOTE: If using the TWO WAY
Resumen del contenido incluido en la página 20
© 2005 Audiovox Electronics Corp., Hauppauge, NY 11788 128-7410 Page 20 128-7410 20 of 20
