Manual de instrucciones de Avanti ProductsK-600HW

Resumen del contenido incluido en la página 1

1.3 Pre-installation test
™

Introduction
Avanti
Observing the correct polarity, Connect the battery to the


terminals marked Batt + -
Avanti is a flexible range of fully featured security control
Security control panels
The panel will now go into alarm condition. Entering the
panels suitable for domestic and light commercial
user code (0123) will silence the system. The Tamper
applications designed to meet the installation

and Power LED’s will be lit with Day & Zone flashin

Resumen del contenido incluido en la página 2

1.8 Test & Commission. Immediate/Silent Set – an immediate program will 2.7 13V Supply SET the system immediately and silently. After the wiring has been completed re-connect the This terminal provides a 13.8V output to power detectors battery to the terminals marked Batt + - and shock sensors etc. Total current available is 350 mA. 2.2 Tamper The panel will now go into alarm condition, enter user code (0123) to silence, the Tamper and Power will be lit Avanti panels come supp

Resumen del contenido incluido en la página 3

3.3 Access Codes 3.7 Service timer 3 Operation Avanti has the following access codes: The Avanti has provision for a service timer, which once 1x Engineer Access code. 1x Holiday Access code. selected is fixed at 900 closings. When expired the 3.1 Programs 1x Manager Access code 4x User Access codes. tamper LED will flash intermittently. The expiration of the The Avanti provides the facility for up to 3 programs that Engineer Access Code – cannot be used t

Resumen del contenido incluido en la página 4

Once a change has been made you need to accept or 4.1.2 Setting Up Timed Zones 4 Engineer Programming abort the changes. Pressing Key A accepts the change On entering Set-up Timed Zones, the zones that are and returns you to the main engineer menu. Pressing Key currently set-up as timed zones will have their respective Once the engineers access code (9999) has been entered B aborts the change and returns you to the main zone LED’s lit. from within DAY mode, the Day LED will be ex

Resumen del contenido incluido en la página 5

4.2 Setting Up Zone Attributes. 4.4 Setting Up the Entry timer. 4.7 Programming Access codes. Set-up Zone Attributes menu is entered from the Set-up Entry Timer menu is entered from the Engineers Programming Access Codes is entered from the Engineers Engineers menu, by pressing Key 2. menu, by pressing Key 4. menu by pressing Key 7 The entry timer may be programmed from 0 seconds to Once the Programming Access codes menu has been Each of the zones has 9 Attributes that dictate it

Resumen del contenido incluido en la página 6

4.9 Test Menu. 4.11 Viewing the Event Log. 5 Remote signalling The Test Menu is entered from the Engineers menu by The Event Log menu is entered from the engineers menu, pressing Key 9. The alarm panel has several test modes by pressing key. Communicator Terminals making life a little easier for the installation engineer. The RS variant of the control panel is fitted with The Day LED will be extinguished to indicate Event Log They are as follows: communicator outputs on the t

Resumen del contenido incluido en la página 7

5.1 Communicator Test Menu It is imperative that the system is fully tested before Battery fuse 1.A QB connecting to a communicator or STU and that the Alarm Receiving Centre (ARC) is receiving signals correctly. The Communicator Test menu is entered from the Engineers menu by pressing Key 9 (Test Menu) and then Key 4. All zone LED’s will be switched off with Day, PA, Tamper and Power LED’s all steady. Press 1 to test Fire output

Resumen del contenido incluido en la página 8

Due to continuous product development, we reserve the right, without prior notice, to alter specifications as and when required. Tel: +44 (0) 1305 853 090 Fax: +44 (0) 1305 851 660 e-mail: sales@keystone-electronics.co.uk