Resumen del contenido incluido en la página 1
INSTRUCTION MANUAL
CEILING SPEAKER SYSTEM F-2352SC
TABLE OF CONTENTS
1. SAFETY PRECAUTIONS .......................... 2 6. REMOVING THE SPEAKER
FOR MAINTENANCE ................................. 9
2. GENERAL DESCRIPTION ........................ 3
7. REPAINTING THE SPEAKER .................. 10
3. FEATURES ................................................ 3
8. SPECIFICATIONS .................................... 11
4. NOMENCLATURE AND DIMENSIONS .... 3
Accessories ..................................
Resumen del contenido incluido en la página 2
1. SAFETY PRECAUTIONS • Be sure to read the instructions in this section carefully before use. • Make sure to observe the instructions in this manual as the conventions of safety symbols and messages regarded as very important precautions are included. • We also recommend you keep this instruction manual handy for future reference. Safety Symbol and Message Conventions Safety symbols and messages described below are used in this manual to prevent bodily injury and property damage which could r
Resumen del contenido incluido en la página 3
2. GENERAL DESCRIPTION The F-2352SC is a 2-way, flush-mounted ceiling speaker that offers a wide frequency range and high-quality sound output. Use of optional mounting hardware permits versatile mounting to match a wide range of applications and installation locations. 3. FEATURES • A rear-open type 2-way speaker system employing a speaker element designed to provide a wide frequency range. • Wide-dispersion flush-mount ceiling speaker design employs unique acoustic construction to realize a
Resumen del contenido incluido en la página 4
5. INSTALLATION A dust cover is pre-mounted on the rear of the speaker at the factory. Pay attention not to accidentally take it off during speaker installation. The F-2352SC ceiling speaker can be mounted in 6 different configurations: • Direct mounting to a strong ceiling panel No additional hardware required. • Direct mounting to a weak ceiling panel Use the optional HY-RR2 Reinforcement Ring. • Mounting to a ceiling frame Use the optional HY-RR2 in conjunction with the optional HY-TB1 Til
Resumen del contenido incluido en la página 5
2-2. Mounting to a ceiling frame Use the optional HY-RR2 Reinforcement Ring in conjunction with the optional HY-TB1 Tile Bar Bridge. Note Refer to the instruction manual included with the HY-TB1 for the correct ceiling mounting procedure. [Installed HY-TB1 and HY-RR2] HY-TB1 (optional) Ceiling frame HY-RR2 (optional) Ceiling panel 2-3. Ceiling mounting in a larger than specified hole Use the optional HY-RR2 Reinforcement Ring in conjunction with the optional HY-TR1 Trim Ring. Note Refer to t
Resumen del contenido incluido en la página 6
2-5. Hanging from a ceiling suspension pipe (exposed installation) Use the optional HY-BC1 Back Can. [Installed HY-BC1] (Example of mounting to suspension pipe) Note Refer to the instruction manual included with the HY-BC1 for Back Can installation. Suspension pipe Caution Ensure that this length is 3 shorter than 53 mm (2 /32"). Speaker cable HY-BC1 (optional) Step 3. Connect the speaker cable to the push-in terminal. Tip Use the 600 V vinyl-insulated cable (IV or HIV wire). The following m
Resumen del contenido incluido en la página 7
4-1. Flush ceiling mounting (in the cases except for Step 2-5) Insert the speaker through the mounting hole till it contacts the ceiling panel. While doing so, avoid directly touching the speaker's diaphragm and diffuser section. Mounting hole WARNING Never grab the diffuser section as a hand hold. The speaker could fall due to damage, resulting in possible personal injury. Diffuser section Diffuser section Rotate and tighten the mounting tab axis screws Mounting tab (3 places) on the unit clo
Resumen del contenido incluido en la página 8
Step 5. Set the input power. Turn the input selector switch (on the unit's front) to set it to the desired input impedance. (Factory-preset to 1.7 kΩ .) Important Never set this switch to low-impedance (8 Ω or 16 Ω ) settings when using a high-impedance 25, 70, or 100 V line. Failure to follow this instruction could result in damage to the speaker or amplifier. Step 6. Attach the front grille. Align the tabs (3 places) on the back side of the grille with the corresponding notches in the unit,
Resumen del contenido incluido en la página 9
6. REMOVING THE SPEAKER FOR MAINTENANCE 6.1. Detaching the Front Grille Turn the front grille counterclockwise to full stop, then lightly 1 Unlock pull it downward. Tip The front grille employs a double-locking system. If the grille cannot be detached when lightly pulled downward, it likely has not yet been fully rotated back to the detachment Front grille position. In such cases, take care to rotate the grill fully counterclockwise in order to release the lock. 2 Pull lightly. 6.2. Removing t
Resumen del contenido incluido en la página 10
7. REPAINTING THE SPEAKER Follow the procedure below when repainting the front grille: Step 1. Clean the front grille before painting. Wipe with a soft cloth dampened in a detergent. Caution Do not use thinner or other volatile liquids to clean the grille. Step 2. Spray on a uniform, thin coat of paint. Cautions • Avoid painting with a roller or brush, as the grille mesh holes could become clogged with paint. • Use appropriate spray paints for the front grille (grille and frame) materials
Resumen del contenido incluido en la página 11
8. SPECIFICATIONS Rated Input 6 W (High Impedance) Power Handling Capacity Continuous pink noise: 9 W (8 Ω ), 6 W (16 Ω ) Continuous program: 18 W (8 Ω ), 12 W (16 Ω ) Impedance 100 V line: 1.7 kΩ (6 W), 3.3 kΩ (3 W), 10 kΩ (1 W), 20 kΩ (0.5 W) 70 V line: 830 Ω (6 W), 1.7 kΩ (3 W), 3.3 kΩ (1.5 W), 10 kΩ (0.5 W), 20 kΩ (0.25 W) 25 V line: 830 Ω (0.75 W), 1.7 kΩ (0.4 W), 3.3 kΩ (0.2 W), 10 kΩ (0.06 W), 20 kΩ (0.03 W) 16 Ω , 8 Ω Sound Pressure Level 89 dB (1 W, 1 m) Frequency Response 80 – 20,000
Resumen del contenido incluido en la página 12
Printed in Indonesia 533-06-094-8A
