Resumen del contenido incluido en la página 1
User’s Manual for ELPLL02 Long-Focal Length Zoom Lens
• This long-focal length zoom lens is designed for use only with EPSON
multimedia projectors.
• It makes it possible to increase the distance between the projector and
the screen.
• Please read this manual completely before use to assure maximum per-
formance.
• Note that illustrations may differ slightly from your actual product.
• Specifications are subject to change without notice.
Safety Precautions
To assure that this product is used saf
Resumen del contenido incluido en la página 2
1. Before mounting the zoom lens 1-1 Safety precautions Warning Be sure to screw the Long-Focal Length lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (especially when the projector is ceiling-mounted). 1-2 Check product contents • Make sure that you have all the parts, as shown below, before starting. Rear lens cap Zoom lens Front lens cap Screwdriver User’s manual (this document) Used to tighter/remove mounting screws •
Resumen del contenido incluido en la página 3
2. Mounting the zoom lens Warning Be sure to disconnect the power cable before installa- tion, because there is danger of electrical shock. Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust. Excessive dust inside the lens could cause damage. • Note that the illustrations below may not match your par- ticular projector model. 2-1 Removing the current lens (1) Remove the front case. 1. Remove the two mounting screws, and pull off the front case. Front case Scr
Resumen del contenido incluido en la página 4
(2) Remove the current lens. 1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens. Current lens 2-2 Mounting the zoom lens (1) Mounting the zoom lens 1. Remove the rear lens cap. 2. Use the enclosed screwdriver to mount the zoom lens with the four mounting screws. Be sure that the seal reading “UPPER” is on top. Seal Rear lens cap 12 Page 12 01.2.15, 4:20 PM
Resumen del contenido incluido en la página 5
(2) Mounting the front case 1. Set the front case into position and tighten the two screws. This completes installation. • Turn on the power and verify that the projector operates nor- mally. Memo Be sure to remove the front lens cap before turning on the power, or it may melt from the heat. 13 Page 13 01.2.15, 4:20 PM
Resumen del contenido incluido en la página 6
4. Zoom lens specifications 4-1 Lens specifications 1. Focal length 68.3 to 116.2 mm 2. Zoom ratio 1.7 x 3. f number 2.14 to 2.98 4. Projection size 60 to 300 inches 5. Mass 2100 g 4-2 Appearance with zoom lens mounted About 505mm 15 Page 15 01.2.15, 4:20 PM
Resumen del contenido incluido en la página 7
User’s Manual for Long Throw Zoom Lens ELPLL03 • This long throw zoom lens is designed for use only with EPSON multi- media projectors. • It makes it possible to increase the distance between the projector and the screen. • Please read this manual completely before use to assure maximum per- formance. • Note that illustrations may differ slightly from your actual product. • Specifications are subject to change without notice. Safety Precautions To assure that this product is used safely, and to
Resumen del contenido incluido en la página 8
1. Before mounting the zoom lens 1-1 Safety precautions Warning Be sure to screw the Long throw zoom lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (es- pecially when the projector is ceiling-mounted). 1-2 Check product contents • Make sure that you have all the parts, as shown below, before starting. Rear lens cap Zoom lens Front lens cap Screwdriver User’s manual (this document) Used to tighter/remove mounting screws •
Resumen del contenido incluido en la página 9
2. Mounting the zoom lens Warning Be sure to disconnect the power cable before installa- tion, because there is danger of electrical shock. Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust. Excessive dust inside the lens could cause damage. • Note that the illustrations below may not match your par- ticular projector model. 2-1 Remove the current lens (1) Remove the front case. 1. Remove the two mounting screws, and pull off the front case. Front case Screw
Resumen del contenido incluido en la página 10
(2) Remove the current lens. 1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens. Current lens 2-2 Mounting the zoom lens (1) Mounting the zoom lens 1. Remove the rear lens cap. 2. Use the enclosed screwdriver to mount the zoom lens with the four mounting screws. Be sure that the seal reading “UPPER” is on top. Seal Rear lens cap 12 Page 12 01.2.15, 4:23 PM
Resumen del contenido incluido en la página 11
(2) Mounting the front case 1. Set the front case into position and tighten the two screws. This completes installation. • Turn on the power and verify that the projector operates nor- mally. Memo Be sure to remove the front lens cap before turning on the power, or it may melt from the heat. 13 Page 13 01.2.15, 4:23 PM
Resumen del contenido incluido en la página 12
4. Zoom lens specifications 4-1 Lens specifications 1. Focal length 144.1 to 194.5mm 2. Zoom ratio 1.35 x 3. f number 2.60 to 3.27 4. Projection size 80 to 300 inches 5. Mass 2100 g 4-2 Appearance with zoom lens mounted About 505mm 15 Page 15 01.2.15, 4:23 PM
Resumen del contenido incluido en la página 13
User’s Manual for ELPLR01 Rear Projector wide Lens • This wide-angle lens is designed for use only on EPSON multimedia projectors. • This lens is designed for use only on rear projection and rear projection box systems. • Please read this manual completely before use to assure maximum per- formance. • Note that illustrations may differ slightly from your actual product. • Specifications are subject to change without notice. Safety Precautions To assure that this product is used safely, and to he
Resumen del contenido incluido en la página 14
1. Before mounting the wide-angle lens 1-1 Safety precautions Warning Be sure to screw the Rear Projector wide lens and adapter ring down completely. Unless they are securely screwed on, they could fall off and cause damage or injury (especially when the projector is ceiling-mounted). 1-2 Check product contents • Make sure that you have all the parts, as shown below, before starting. Screwdriver Rear lens cap Zoom lens Front lens cap Used to tighter/remove mounting screws Hex wrench User’s manua
Resumen del contenido incluido en la página 15
2. Mounting the rear-projection wide-angle lens Warning Be sure to disconnect the power cable before installa- tion, because there is danger of electrical shock. Memo Always mount and dismount the lens in a clean room, to minimize the amount of dust. Excessive dust inside the lens could cause damage. • Note that the illustrations below may not match your particu- lar projector model. 2-1 Removing the current lens (1) Remove the front case. 1. Remove the two mounting screws, and pull off the fron
Resumen del contenido incluido en la página 16
(2) Remove the current lens. 1. Use the enclosed screwdriver to remove the four mounting screws, and dismount the current lens. Current lens 2-2 Mounting the rear-projection wide-angle lens (1) Mounting the rear-projection wide-angle lens 1. Remove the rear lens cap. 2. Use the enclosed screwdriver to mount the rear projector wide lens with the four mounting screws. Be sure that the seal read- ing “UPPER” is on top. Seal Rear lens cap 14 Page 14 01.2.15, 4:17 PM
Resumen del contenido incluido en la página 17
(2) Adjusting the wide lens for a rear projector • This lens must be adjusted to match the screen size. Adjust the lens as follows, before installing the front case. 1. Turn the lens shift button to move the lens all the way down. 2. Loosen the 2 focus ring mounting screws by using the hex wrench that came in the same package. 3. Loosen the 2 resolving plane correction ring mounting screws with the hex wrench. 4. Turn on the projector power. 5. Rotate the two rings to adjust the image to the opt
Resumen del contenido incluido en la página 18
(3) Mounting the front case 1. Set the front case into position and tighten the two screws. This completes installation. • Turn on the power and verify that the projector operates nor- mally. 16 Page 16 01.2.15, 4:17 PM
Resumen del contenido incluido en la página 19
4. Rear-projection wide-angle lens specifications 4-1 Lens specifications 1. Focal length 27mm 2. f number 2.3 3. Projection size 60 to 100 inches 4. Mass 1600 g 4-2 Appearance with rear projector wide lens mounted About 455mm 18 Page 18 01.2.15, 4:17 PM
Resumen del contenido incluido en la página 20
User’s Manual for ELPLS01 Standard Lens • This standard lens is designed for use only with EPSON multimedia pro- jectors. • Please read this manual completely before use to assure maximum per- formance. • Note that illustrations may differ slightly from your actual product. • Specifications are subject to change without notice. Safety Precautions To assure that this product is used safely, and to help prevent dam- age or injury, the following symbols are used in the manual. Please read this manu
