Manual de instrucciones de Bogen CommunicationsGA6A

Resumen del contenido incluido en la página 1

Utility Amplifier
GA6A Model
Installation and Use Manual
© 2004 Bogen Communications, Inc.
All rights reserved.
Specifications subject to change without notice.
54-5757-03B 0406

Resumen del contenido incluido en la página 2

Notice IMPORTANT Every effort was made to ensure that the information in this manual was complete and accurate at the time of printing. However, information is subject to change. Important Safety Information CAUTION: TO PREVENT THE RISK OF ELEC- WARNING: To Reduce The Risk of Fire Or Electric Shock, TRIC SHOCK, DO NOT REMOVE COVER (OR Do Not Expose This Apparatus To Rain Or Moisture. BACK). NO USER-SERVICEABLE PARTS Always follow these basic safety precautions when installing and INSIDE. REFER S

Resumen del contenido incluido en la página 3

Description The GA6A is a rugged six-watt, dual-input audio amplifier with a wide variety of smaller applications including background music, relaying communication from one room to another, or sound reinforcement. The GA6A delivers rated power at not more than 1% total harmonic distortion from 75-15,000 Hz into transformer-coupled or direct low-impedance loads. Inputs for a low-impedance balanced dynamic microphone and an auxiliary audio source (tuner, tape deck, etc.) can be mixed. Individua

Resumen del contenido incluido en la página 4

Panel Descriptions Utility Amplifier Front Panel 1. MIC Control - Regulates the level of microphone output to speakers. 2. AUX Control - Regulates the level of the AUX source to speakers. 3. Power Switch - Controls AC power to the amplifier. Illuminates when ON. Utility Amplifier Rear Panel 1. Speaker Output Barrier Strip - Output terminal strip provides for 8-ohm, 25V, and 70V speaker outputs. 2. Shorting Link - Used when 25V or 70V speakers are to be connected to the GA6A. Must be removed if

Resumen del contenido incluido en la página 5

Connections 70V & 25V Speaker Systems Connect the 25V or 70V speaker loads to the corresponding terminals (25V or 70V) and the common terminal. Make sure that the total wattage of all the connected speakers is less than 6 watts. Note: Do not use both the 25V and 70V terminals at the same time. Use only one type of speaker (25V or 70V) for all speakers connected to the GA6A. Note: If using multiple speakers, check for proper phasing. See Section on Phasing. Link The shorting link must be i

Resumen del contenido incluido en la página 6

Connections Phasing As the voltage on a speaker changes from plus to minus, the speaker cone moves from pushing out to pulling in. If you reverse the polarity, the speaker responds in the opposite manner. If a speaker is pushing out and an adjacent speaker is pulling in, some of the pressure caused by the speaker pushing out will be absorbed by the speaker pulling in. These two speakers are operating out of phase. In a paging system, all the speakers should be in pha

Resumen del contenido incluido en la página 7

Operation Power The AC line cord should be plugged into a three-wire, grounded outlet providing 120V AC, 60 Hz.The power switch illuminates when unit is switched ON. MIC Control Controls the amount of MIC signal heard at the output. Clockwise increases the signal. AUX Control Controls the amount of AUX signal heard at the output. Clockwise increases the signal. Treble Control Switch Provides a stepped increase or decrease in high frequency (above 10 kHz) heard at the output.The “Cut” position

Resumen del contenido incluido en la página 8

Specifications Power Output: 6 watts RMS Frequency Response: 30 Hz - 12 kHz +0 dB, -3 dB Total Harmonic Distortion: Less than 1% at rated output power Inputs: Lo-Z MIC, balanced;AUX Sensitivity: MIC 0.3 mV;AUX 0.2V Hum & Noise: MIC -50 dB;AUX -70 dB Output Impedance: 8 ohms, 25V and 70V speakers Tone: Treble boost at 10 kHz 9 dB, treble cut at 10 kHz 9 dB (switch selected) Controls: MIC,AUX, illuminated POWER switch, tone switch Terminations: Outputs & microphone: screw terminals Auxiliary: RCA