Manual de instrucciones de Planet Technology POE-400

Resumen del contenido incluido en la página 1

IEEE 802.3af
4-Port Power over Ethernet Injector Hub


POE-400

User’s Manual






- 1 -

Resumen del contenido incluido en la página 2

Trademarks Copyright  PLANET Technology Corp. 2006. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a

Resumen del contenido incluido en la página 3

TABLE OF CONTENTS 1. INTRODUCTION.......................................................................................................................................... 4 1.1 CHECKLIST ................................................................................................................................................ 4 1.2 ABOUT THE POWER OVER ETHERNET INJECTOR HUB................................................................................... 4 1.3 FEATURES .............

Resumen del contenido incluido en la página 4

1. INTRODUCTION 1.1 Checklist Thank you for purchasing our POE-400 IEEE 802.3af Power over Ethernet Injector Hub, your Power over Ethernet Injector Hub package shall contains following contents: Check the contents of your package for following parts:
Power over Ethernet Injector Hub x1
User's manual CD x1
Power Adapter x1
Power cord x 1 If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the origin

Resumen del contenido incluido en la página 5

1.4 Specification Model POE-400 Ethernet Connector 8-Port RJ-45 STP with 4-Port "Data" and 4-Port "Data and Power" Ethernet Data rate 10/100Mbps( vary on Ethernet device attached) Input voltage DC 48V, 1.5A Number of device can be powered 4 Ethernet cable TIA/EIA-568, Category 5/5e cable LED indicator 1 x power, 4 x POE ready / in-use Operating environment 0~50 Degree C, 5%~90%RH Storage environment -20~70 Degree C, 5%~90%RH Dimension (H x W x D) 26 x 70 x 97mm Weight 220g Emissi

Resumen del contenido incluido en la página 6

2. HARDWARE INSTALLATION This product provides two different running speeds – 10Mbps, 100Mbps, in the same device and automatically distin- guishes the speed of incoming connection. This section describes the hardware features of POE-400. Before connecting any network device to the POE-400, read this chapter carefully. 2.1. Before Installation Before your installation, it is recommended to check your network environment. If there is any IEEE 802.3af devices need to power on, the POE-40

Resumen del contenido incluido en la página 7

2.2 POE-400 and POE-152S, the IEEE 802.3af Injector / Splitter and equipment installation For the places hard to find the power inlet, the POE-400 provide the easiest way to power your Ethernet devices such as PLANET IEEE 802.3af Power over Ethernet Splitter( POE-152S) with Internet Camera (ICA-210 ) or Wireless Access Point (WAP-4060PE) installed in the small office. To control the power system of your networking devices, the POE-400 can directly co-work with PLANET ICA-100PE and POE I

Resumen del contenido incluido en la página 8

3. TROUBLESHOOTING This chapter contains information to help you solve problems. If the Switch is not functioning properly, make sure the Ethernet Switch was set up according to instructions in this manual. How to let my non IEEE 802.3af network devices can work with POE-400? Solution: You can use PLANET Power over Ethernet Splitter, such as PLANET POE-152S to work as a power transformer between POE-400 and non IEEE 802.3af devices. Two types of POE-152S are available for differ

Resumen del contenido incluido en la página 9

APPENDIX A NETWORKING CONNECTION A.1 Switch‘s RJ-45 Pin Assignments 10/100Mbps, 10/100Base-TX RJ-45 Connector pin assignment MDI MDI-X Contact Media Dependant Media Dependant Interface Interface -Cross 1 Tx + (transmit) Rx + (receive) 2 Tx - (transmit) Rx - (receive) 3 Rx + (receive) Tx + (transmit) 4, 5 IEEE 802.3af DC 48V 6 Rx - (receive) Tx - (transmit) 7, 8 IEEE 802.3af DC 0V A.2 RJ-45 cable pin assignment The standard RJ-45 receptacle/connector There are 8 wires on