Resumen del contenido incluido en la página 1
IEEE 802.3af
Power over Ethernet Injector
POE-152
User’s Manual
- 1 -
Resumen del contenido incluido en la página 2
Trademarks Copyright Ó PLANET Technology Corp. 2006. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a
Resumen del contenido incluido en la página 3
TABLE OF CONTENTS 1. INTRODUCTION.......................................................................................................................................... 4 1.1 CHECKLIST ................................................................................................................................................ 4 1.2 ABOUT THE POWER OVER ETHERNET INJECTOR .......................................................................................... 4 1.3 FEATURES .........
Resumen del contenido incluido en la página 4
1. INTRODUCTION 1.1 Checklist Thank you for purchasing our POE-152 IEEE 802.3af Power over Ethernet Injector, your Power over Ethernet Injector package shall contains following contents: Check the contents of your package for following parts: Power over Ethernet Injector x1 User' s manual CD x1 Power Adapter x1 Power cord x 1 If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing
Resumen del contenido incluido en la página 5
1.4 Specification Model POE-152 Ethernet Connector 2 x RJ-45( 1 for data + DC out, 1 for Data in) Ethernet Data rate 10/100/1000Mbps( vary on Ethernet device attached) Input voltage DC 48V, 0.4A Number of device can be powered 1 Ethernet cable TIA/EIA-568, Category 5/5e/6 cable LED indicator 1 x power, 1 x POE ready / in-use Operating environment 0~50 Degree C, 5%~90%RH Storage environment -20~70 Degree C, 5%~90%RH Dimension (W x D x H) 73 x 55 x 24 mm Weight 50g Emission FCC Class
Resumen del contenido incluido en la página 6
2. HARDWARE INSTALLATION This product provides three different running speeds – 10Mbps, 100Mbps, 1000Mbps in the same device and auto- matically distinguishes the speed of incoming connection. This section describes the hardware features of POE-152. Before connecting any network device to the POE-152, read this chapter carefully. 2.1 Before Installation Before your installation, it is recommended to check your network environment. If there is any IEEE 802.3af devices need to power on, t
Resumen del contenido incluido en la página 7
2.2 POE-152, the Injector installation 1. Connect a standard network cable from Switch/workstation to “Ethernet” port of POE-152. 2. Connect the long cable that will be used to connect to the remote device to the port “Ethernet + DC”. The screen in Figure 1 appears. 3. Connect the AC adapter to “DC 48V” of POE-152. The power LED will be steady on. Figure 1: the Injector installation 2.3 POE-152 and POE-152S, the IEEE 802.3af Injector and Splitter installation 1. Connect a standard net
Resumen del contenido incluido en la página 8
Figure 3: Connection architecture over POE-152/152S Notice: 1. According to IEEE 802.3af standard, the POE-152 will not inject power to the cable if not connecting to IEEE 802.3af devices. 2. Please ensure the output voltage is correct before applying power to remote device. 2.4 Connect with IEEE 802.3af devices Due to the capability of IEEE 802.3af standard, the POE-152 can directly connect with any IEEE 802.3af end-nodes like wireless access point, VoIP phones and Int
Resumen del contenido incluido en la página 9
3.TROUBLESHOOTING This chapter contains information to help you solve issues. If the POE-152 is not functioning properly, make sure the POE-152 was set up according to instructions in this manual. The PoE LED is not lit Solution: Check the cable connection between POE-152 and IEEE 802.3af device. Why I connect my PoE device to POE-152 and it cannot power on? Solution: 1. Please check the cable type of the connection from POE-152 to the other end. The cable should be an 8-wire UTP,
Resumen del contenido incluido en la página 10
APPENDIX A NETWORKING CONNECTION A.1 Switch‘s RJ-45 Pin Assignments 1000Mbps, 1000Base T Contact MDI MDI-X 1 BI_DA+ BI_DB+ 2 BI_DA- BI_DB- 3 BI_DB+ BI_DA+ 4 BI_DC+ BI_DD+ 5 BI_DC- BI_DD- 6 BI_DB- BI_DA- 7 BI_DD+ BI_DC+ 8 BI_DD- BI_DC- 10/100Mbps, 10/100Base-TX RJ-45 Connector pin assignment MDI MDI-X Contact Media Dependant Media Dependant Interface Interface -Cross 1 Tx + (transmit) Rx + (receive) 2 Tx - (transmit) Rx - (receive) 3 Rx + (receive) Tx + (transmit) 4, 5 Not
Resumen del contenido incluido en la página 11
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cable and crossover cable connection: Figure A-1: Straight-Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network. 2080-A31120-001
