Resumen del contenido incluido en la página 1
RCTS-MLT Remote Control Kits
-For use with SIT Millivolt Valves only-
- Installation and Operating Instructions -
INTRODUCTION
CAUTION: All wiring should be done by a qualifi ed electrician
The remote control system can be operated thermostatically and shall be in compliance with local codes and with the
National Electric Code ANSI/NFPA No. 70-current (in the
or manually from the transmitter. The system operates on
United States), or with the current CSA C22.1 Canadian
radio frequencies (RF
Resumen del contenido incluido en la página 2
TP TH TP TH TP TH TP TH Canadian Equipment Requirements WARNING This digital apparatus does not exceed the (Class A/Class B)* limits for radio noise emissions from digital apparatus Shock hazard. set out in the Radio Interference Regulations of the • Leave electrical power off at this time. Canadian Department of Communications. Le present • Do not restore power until the remote control system is completely installed. appareil numerique n’emet pas de bruits radioelectriques depassant les li
Resumen del contenido incluido en la página 3
Alternative Wiring for units with a wall switch Disconnect the wall switch wire from the TH terminal on A the valve and connect this wire to male connector supplied on the receiver. Connect remaining female connector from receiver to the TH terminal on the valve. B Adding Optional Fan/Blower Plug 2-prong fan cord directly into the 3 prong polarized plug on the back of the receiver (see Figure 3). This receptacle output is 110/120 VAC, 3 AMP. C (Receptacle on back) LEARN 110/120 VAC, 3A REMO
Resumen del contenido incluido en la página 4
4. Light the fi replace as directed in the Owner’s Manual. Adjusting “Low Flame” setting (LP ONLY) 1. Using a 5/16 in. slotted screwdriver turn brass screw 5. Adjust “High Flame” by turning solenoid clockwise to inside regulator tower two complete rotations clock- increase pressure and counterclockwise to reduce wise. See fi gure 6. pressure. Adjust until the reading on the manometer is 3.5 inches w.c. for natural gas and 10 in w.c. for LP. 6. Tighten jam nut (Figure 4 and Figure 7) to the fac
Resumen del contenido incluido en la página 5
REMOTE RECEIVER TRANSMITTER The remote receiver has a 3-position slide switch: OFF/ Important: Before operating remote control, transmitter REMOTE/ON (see Figure 7). and receiver must have matching security codes. See section ‘Matching Security Codes’. Important: Review ‘Thermo-Updating/Communication- Safety Features’ under ‘Transmitter Safety Features’ sec- tion. Communication Safety features shut down the fi re- place system when a potentially unsafe condition exists. Important: Review ‘Auto
Resumen del contenido incluido en la página 6
1. LOW - Battery power low. Replace batteries within two weeks. 2. TIMER - Indicates time remaining before system shuts off, when timer-programmed, 9 - hour maximum setting. 3. MODE - Indicates operation MODE of system. ON indicates the system is on, either manually or thermostatically. THERMO indicates the system will automatically cycle ON/OFF, depending on programmed SET temperature. OFF indicates the entire system is turned off. 4. SET - Indicates desired SET room temperature for THERMO
Resumen del contenido incluido en la página 7
NOTE: To prevent repeated thermo-cycling of the gas appliance, the sensing unit in the transmitter will only ac- tivate the remote receiver when the temperature change exceeds 20 F (10 C) above or below the SET (desired) temperature. When the transmitter is in the THERMO mode, it should be kept away from direct sources of heat such as fi replaces, incandescent lighting and direct sunlight. Leaving the trans- mitter in direct sunlight, for example, will cause it to read SETTING BUTTON the ro
Resumen del contenido incluido en la página 8
Adjusting the Flame Height - Should the receiver NOT receive a transmitter signal every 15 minutes (COMMUNICATION-SAFETY feature), the RE- Operates in ON or THERMO mode CEIVER will begin a 2 HOUR (120 minute) countdown tim- This remote control system allows the user to control the ing function. If during this 2 hour period, the receiver does height of the FLAME when the gas valve is factory equipped not receive a signal from the transmitter, the RECEIVER with a FLAME CONTROLLER. will shut d
Resumen del contenido incluido en la página 9
7. Set the SET temperature to at least 2º F (1º C) below GENERAL INFORMATION the room temperature and the system fl ame will extin- Transmitter Wall Bracket guish. Thereafter, it should continue to cycle on and off thermostatically approximately every two minutes The transmitter can be hung on a wall using the bracket as the ROOM temperature changes, but only when provided. Locate the bracket on an inside wall suffi ciently the temperature differential between ROOM and SET far away from direct
Resumen del contenido incluido en la página 10
PILOT THERMOPILE THERMOCOUPLE PIEZO THERMOSTAT WIRE ASSEMBLY RED VALVE Figure 10. Standing Pilot Ignition Wiring Diagram STANDING PILOT BRN RED VALVE ON/OFF PIGGYBACK WIRE WHT THERMOSTAT WIRE ASSEMBLY RED Figure 11. Standing Pilot Ignition Wiring Diagram with Piggyback Wire STANDING PILOT REMOTE SWITCH PIGTAIL ON OFF ON/OFF VALVE SWITCH WHT OPTIONAL WALL SWITCH, RED THERMOSTAT OR REMOTE Figure 12. Standing Pilot Ignition Wiring Diagram 10 WHITE
