Manual de instrucciones de Panasonic mc-v41500

Resumen del contenido incluido en la página 1

Order Number MAC0506021C1
Vacuum Cleaner
MC-V415 00
Specifications are subject to change without notice for further improvement.
© 2005 PANASONIC CONSUMER ELEC-
TRONICS COMPANY, DIVISION OF PANA-
SONIC CORPORATION OF NORTH
AMERICA. All rights reserved. Unauthorized
copying and distribution is a violation of law.

Resumen del contenido incluido en la página 2

1 WIRING DIAGRAM AND DRAWING 1.1. Wiring Diagram 2

Resumen del contenido incluido en la página 3

1.2. PICTORIAL DIAGRAM NOTE: For general servicing, it is necessary to eliminate pinching of any wire during reassembly. After servicing any electrical compo- nent or electrical enclosure, the unit should be reassembled and checked for dielectric breakdown or current leakage. 3

Resumen del contenido incluido en la página 4

2 EXPLODED VIEW AND PARTS LIST 2.1. Body 2.1.1. Exploded View 4

Resumen del contenido incluido en la página 5

2.1.2. Parts List (Body) Ref No. Part No. Part Name & Description Quantity Remarks 1 AC88KCUGZV07 Dust Container Unit 1 2 AC60KBRSZU01 Dust Cover Assembly 1 3 AC94EAPNZY02 Power Cord 1 4 AMC-1CTCE23 Wire Connector 6 Shipped 10 per package 5 AC02LBJAZ000 Rear Cover Packing 1 6 AC40AYUZV00 Packing (Left) 1 7 AC39AAJFZV00 Packing (Right) 1 8 AC01EAMMZ000 Switch On-Off 1 9 AC01EAMMZV07 ON/OFF Button 1 10 AC03EAMMZV07 Switch Cover 1 11 AXTN4+16BFY Screw 1 Shipped 10 per package 12 AC23PJPZV07 Hose Ho

Resumen del contenido incluido en la página 6

2.2. Nozzle Housing 2.2.1. Exploded View 6

Resumen del contenido incluido en la página 7

2.2.2. Parts List (Nozzle Housing) Ref. No. Part No. Part Name & Description Quantity Remarks 1 AC01ACHTZU03 Nozzle Housing 1 Includes item 4 2 AC21H2XZU03 Window 1 3 AMC25S-V00 Shaft (Plastic) 1 4 AC10A2VZV07 Furniture Guard 1 5 AMC81A-V00 Packing (Nozzle) 1 6 AMC43A-2V0 Frame 1 7 AMC58A-2V0 Spring (Pedal) 1 8 AMC47A-2V0U Pedal 1 9 AXTN4+16BFY Screw (Frame) 3 Shipped 10 per package 10 AC28SJPZ00 Belt 1 11 AC91AARFZ00 Lower Plate Assembly 1 12 AC27AADGZ00 Lower Plate 1 13 AC07ZADFZ00 Warning Lab

Resumen del contenido incluido en la página 8

2.3. Packing Material 2.3.1. Exploded View 2.3.2. Parts List Ref. No. Part No. Part Name & Description Quantity Remarks 1 AC61ZCHTZ000 Packaging Assembly 1 Includes 1 and items a-g 2 AC01ZCUGZ000 Operating Instructions 1 8

Resumen del contenido incluido en la página 9

3 REPLACEMENT INSTRUCTIONS to be replaced. 3.1. Lower Plate 3.1.1. Removal 1. Place handle in low position. 2. Turn the vacuum cleaner over exposing the underside. Release the lower plate by pressing the two (2) latches that secure it inward. 3. Separate the lower plate from the vacuum. 2. Carefully lift up on the agitator assembly until it clears both sides of the nozzle housing. 3.1.2. Installation 1. Close the rear belt cover. 2. Hook the front of the lower plate into the slots on the front o

Resumen del contenido incluido en la página 10

3. Reassemble the new agitator assembly back into the noz- 3.4.2. Installation zle housing by placing the side opposite the belt partially 1. Install the nozzle packing, if not already in place, window into the slot. The small tabs should be aligned with the and handle release assembly in the new nozzle housing. nozzle. This will hold the agitator in place and leave both 2. Fit the nozzle around the motor shaft side first, and rotate hands free to place enough tension on the belt to allow it int

Resumen del contenido incluido en la página 11

3.5. Power Cord Replacement 3.6. On / Off Switch 3.5.1. Removal 3.6.1. Removal 1. Remove the seven (7) screws that secure the dust cover 1. Remove the nozzle cover, agitator assembly, belt and and remove the dust cover. nozzle base. 2. Remove the seven (7) screws that secure the dust cover and remove the dust cover. 3. To replace the on-off switch, remove the plastic holder that is mounted over the motor shaft. Lift the motor up and out of the dust compartment. Take care to note the position of

Resumen del contenido incluido en la página 12

3.7. Motor Protector Replacement 3.7.1. Removal 1. Remove the seven (7) screws that secure the dust cover and remove the dust cover. 2. Remove the motor protector located inside the dust com- partment by pushing in on the two retaining tabs. Do one side at a time while pushing out on the motor protector from inside the dust compartment. 3. Once the motor protector has been removed it can be dis- assembled for replacement of parts. 3.7.2. Installation 1. Reinstall the motor protector into the dus

Resumen del contenido incluido en la página 13

13