Manual de instrucciones de Sanitaire 6000

Resumen del contenido incluido en la página 1

Commercial
Floor Machine
6000 Series
Owner’s Guide
Index
Important Safeguards ................. 2
General Information .................... 2
Grounding Instructions ............... 3
Operation/Accessories ............... 3
Remove From Carton ................. 4
Brush & Drive Block Installation .. 5
Adjustments ................................ 5
Controls ...................................... 6
Guidelines For Operation ............ 6
Cord Storage .............................. 7
Clean Up And Stora

Resumen del contenido incluido en la página 2

IMPORTANT SAFEGUARDS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER. WARNING To reduce the risk of fire, electric shock, or injury: Your machine is equipped with a safety switch lock and  Do not pull, close a door on, or pull the cord around sharp  power switch triggers designed for your safety. Do not edges or corners. Keep the cord away from heated surfaces. attempt to bypass or

Resumen del contenido incluido en la página 3

Grounding Instructions This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for OPERATION/ACCESSORIES electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment- Choosing the Right Brush and Drive Block grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed Your floor machine is packed complete and ready for use af

Resumen del contenido incluido en la página 4

HOW TO REMOVE POLISHER FROM SHIPPING CRATE 1. Lift up on handle to 2. Move upper handle forward to expose 3. Remove the wing nuts release lock. wing nuts and angle bracket. and bolts from both upper and lower handle. Discard the angle bracket. 4. Lift upper handle and 6. Handle sleeve and bolts 5. Use a screwdriver to line up place end-to-end against will look like this when they holes and guide bolts through lower handle, lining up the are properly installed. the handle. holes for the bolts. Sl

Resumen del contenido incluido en la página 5

BRUSH AND PAD DRIVER ADJUSTMENTS INSTALLATION CAUTION: Disconnect the power cord from the electrical DRIVE BELT ADJUSTMENT outlet before installing a brush or pad driver. (Model 20” 1500 rpm 1.5 HP only) CAUTION: Disconnect the power cord from the electrical outlet before adjusting drive belt tension. ON OFF 1. Loosen the bolts holding the drive motor to the frame; do not remove (Fig. 6). 2. Turn the two screws at the rear of the frame until the belt is tight. 3. Test the machine. If belt slips

Resumen del contenido incluido en la página 6

ADJUSTMENTS (Continued) HANDLE CAM LOCK ADJUSTMENT With the handle cam lock in the “up” position (unlocked), tighten To stop the machine, simply release the triggers. The safety the adjusting nuts until there is a slight drag when the handle switch lock will automatically return to the engaged position. is raised or lowered. The tube should be locked securely when the handle lock is pressed downward (Fig. 8). USING THE 20” 175/300 rpm 2-speed FOR BUFFING (Models SC6030, SC6035) The model 20” 175

Resumen del contenido incluido en la página 7

CORD STORAGE When not in use, loosely wind the power cord around the cord storage hook on the handle shaft and both of the handle grips, as shown. CLEAN UP AND STORAGE After being used, your floor machine can be wiped clean with a soft, damp cloth and should be stored in a clean, dry place. 7

Resumen del contenido incluido en la página 8

EUREKA SANITAIRE COMMERICAL EQUIPMENT LIMITED WARRANTY Floor Machines / Air Movers Excludes Vacuums Your equipment which has been manufactured, tested and inspected in accordance with carefully specified engineering requirements is warranted to be free from defects in material and workmanship. This Limited Warranty is, however, subject to the following qualifications, conditions and limitations which are set forth to provide you and all users of the equipment with information concerning the dur