Resumen del contenido incluido en la página 1
Snapshot
LXW
OK on Dimmer
Outdoor OK
Sound Activated
DMX512
Master/Slave
115V/230V Switch
Replaceable Fuse
User Serviceable
Linking power
USER MANUAL
th
3000 N 29 Ct, Hollywood, FL 33020 U.S.A.
(800) 762-1084 – (954) 929-1115
FAX (954) 929-5560
www.chauvetlighting.com
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS 1. Before You Begin ................................................................................................................................ 2 What is included ....................................................................................................................................... 2 Unpacking Instructions .............................................................................................................................. 2 AC Power ...........
Resumen del contenido incluido en la página 3
AC Power To determine the power requirements for a particular fixture, see the label affixed to the back plate of the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average current draw under normal conditions. All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100% switch. Before applying power
Resumen del contenido incluido en la página 4
Safety Instructions Please read these instructions carefully, which includes important information about the installation, usage and maintenance of this product. Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel o
Resumen del contenido incluido en la página 5
Product Overview Hanging bracket Bracket adjustment knob Voltage selection switch 1. Microphone Safety eyebolt Mode selection switch Sound sensitivity adjustment Power in/fuse holder External Power ground link out screw LXW User Manual 5 12/31/2008 4:21 PM
Resumen del contenido incluido en la página 6
Disconnect the power cord before replacing a fuse and always replace with the same type fuse. Fuse Replacement Using a flat head screwdriver, wedge the fuse The fuse is located holder out of its housing. Remove the damaged inside this fuse from its holder and replace with exact compartment. same type fuse. Insert the fuse holder back in Remove using a flat its place and reconnect power. head screwdriver. Mounting ORIENTATION This fixture may be mounted in any safe p
Resumen del contenido incluido en la página 7
3. OPERATING INSTRUCTIONS Operation Stand-Alone Mode (constant rotation, static, and sound active mode): Constant rotation Static (no rotation) Sound Active mode The above illustration is of the Mode selection switch on the rear of the fixture. There are 3 modes: constant rotation, static, and sound active mode. Note: the light will not turn off. It operates with a constant on. 1) The unit will react to the low frequencies of music via the internal microphone in
Resumen del contenido incluido en la página 8
General Troubleshooting Applies to Foggers Dimmers Symptom Solution(s) Lights & Snow Controllers & Chaser Beam is very dim or Clean optical system or replace lamp not bright Check 220/110v switch for proper setting Breaker/Fuse keeps Check total load placed on device blowing Device has no power Check for power on Mains. Check device’s fuse. (internal and/or external) Fixture is on but Make sure you have the correct audio mode on the there is no control switches.
Resumen del contenido incluido en la página 9
4. APPENDIX General Maintenance To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a month. Dust build up reduces light output performance and can cause overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off fixture before conducting maintenance. Unplug fixture from power. U
Resumen del contenido incluido en la página 10
Technical Specifications WEIGHT & DIMENSIONS Length ................................................................................................................................ 9.5 in (242 mm) Width .................................................................................................................................. 5.2 in (132 mm) Height ................................................................................................................................. 7.7 in (1
