Resumen del contenido incluido en la página 1
HD CAMERA CONTROL UNIT
HDCU-950
SD ENCODER UNIT
HKCU-951
HD FRAME RATE CONVERTER UNIT
HKCU-953
INSTALLATION AND MAINTENANCE MANUAL
1st Edition (Revised 3)
Serial No. 10001 and Higher : HDCU-950
Serial No. 10001 and Higher : HKCU-951
Serial No. 10001 and Higher : HKCU-953
Resumen del contenido incluido en la página 2
! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! WARNUNG Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die Gefahr eines elektrischen Schlages, F
Resumen del contenido incluido en la página 3
For HDCU-950 For HDCU-950 Laser Diode Properties Attention-when the product is installed in Rack: Material : In GaAsP Wave length : 1310 ±40 nm 1. Prevention against overloading of branch circuit Emission duration : Continuous When this product is installed in a rack and is Laser output power: _8 dBm supplied power from an outlet on the rack, please make sure that the rack does not overload the supply circuit. For HDCU-950 2. Providing protective earth When this product is installed in a rack an
Resumen del contenido incluido en la página 4
Resumen del contenido incluido en la página 5
Table of Contents Manual Structure Purpose of this manual ........................................................................................ 3 (E) Related manuals................................................................................................... 3 (E) Contents ............................................................................................................... 4 (E) Trademark..........................................................................................
Resumen del contenido incluido en la página 6
2. System Setup 2-1. System Connection................................................................................2-1 (E) 2-1-1. Standard System ...................................................................2-2 (E) 2-1-2. Standard HD/SD System ......................................................2-3 (E) 2-1-3. HD/SD Film Like System ....................................................2-4 (E) 2-1-4. Analog NTSC/PAL System .................................................2-5 (E) 2-2. Set
Resumen del contenido incluido en la página 7
Manual Structure Purpose of this manual This manual is the installation and maintenance manual of the following models : HD Camera Control Unit HDCU-950 SD Encoder Unit HKCU-951 HD Frame Rate Converter Unit HKCU-953 This manual is intended for use by trained system and service engineers, and describes the information regarding the installation of the unit and the information required for initial service. Related manuals Beside this Installation and Maintenance Manual, the following manuals are a
Resumen del contenido incluido en la página 8
Contents The following is a summary of the sections of this manual. Section 1 Installation Overview Describes how to checking the ROM version, connectors and cables, setting of switches on boards, function of the indicators on boards, installing in 19-inch rack, etc. Section 2 System Setup Describes how to set and adjust when connecting the unit to the camera system. Section 3 Service Overview Describes recommended replacement parts, how to cleaning connector/cables and charactor display functio
Resumen del contenido incluido en la página 9
Section 1 Installation Overview 1-1. Checking the ROM and Software Version When connecting the following peripheral equipment to the unit, confirm that the versions of the ROMs and software which are installed in each model. If the version is lower than the following one, the ROM needs to be replaced and the software needs to be upgraded. In this case, contact your local Sony Sales Office/Service Center. ROM Peripheral equipment Board Ref. No. ROM version MSU-700A CPU-293 IC5, IC6 Ver. 1.10 or
Resumen del contenido incluido en la página 10
1-3. Power Cord 1-4. Matching Connectors and Cables 1-3. Power Cord 1-4. Matching Connectors and Cables w 1-4-1. Connector Input/Output Signal The power cord is not supplied with this unit. Be sure to use the specified power cord. BNC Connector Do not use the damaged power cord. HDCU-950 For U.S.A. and Canada 1 Power cord 125 V 10 A (2.4 m) :! 1-551-812-11 1125 digital signal 2 Plug holder (black) : 2-990-242-01 RET (1 to 3) IN : BNC Conforms to BTA-S004B, 1.485 Gbps/1.4835 Gbps AC inlet SMPTE 2
Resumen del contenido incluido en la página 11
1-4. Matching Connectors and Cables CAMERA connector (optical/electrical composite connector) HKCU-951 (525/625 analog signal) Y/G OUT : BNC VIDEO Y/PB/PR Y : 1.0 V p-p (video: 0.714 V, sync : 0.286 V ), 75 Z Conforms to BTA-S004B, 1.485 Gbps/ G : 0.7 V, 75 Z 1.4835 Gbps serial SMPTE 292M B-Y/B OUT : BNC RET VIDEO Y/PB/PR B-Y : 0.756 V p-p, 75 Z (when 75 % color bar is input) Conforms to BTA-S004B, 1.485 Gbps/ B : 0.7 V, 75 Z 1.4835 Gbps serial SMPTE 292M R-Y/R OUT : BNC INCOM 2ch R-Y : 0.756 V
Resumen del contenido incluido en la página 12
1-4. Matching Connectors and Cables MIC1/MCI2 (XLR 3-pin, Male) *1 : CHU MIC 1/2 AMP GAIN CONT0 CONT1 CONT2 CHU MIC AMP GAIN 12 H H H 60 dB 3 L H H 50 dB H L (H) H (L) 40 dB L L (H) H (L) 30 dB _____ EXT VIEW _____ H H (L) L (H) 20 dB (0 dBu = 0.775 Vrms) The setup for HDCU-700A mode is shown in parenthesis ( ). In the case of HDCU-700A mode : S423-2/AT-149 → ON No. Signal Specifications 1 MIC OUT (G) 0 dBu/_20 dBu *2 : 2 MIC OUT (X) (Selectable with S502, 8pin 15pin MIC GAIN CONT 3 MIC OUT (Y)
Resumen del contenido incluido en la página 13
1-4. Matching Connectors and Cables INCOM/TALLY/PGM (D-sub 25-pin, Female) WF MODE (4-pin, Female) 13 1 4 1 3 2 25 14 _____ EXT VIEW _____ _____ EXT VIEW _____ No. Signal Specifications (0 dBu = 0.775 Vrms) 1 SEQ CONT OUT (G) OPEN COLLECTOR No. Signal Specifications +(PNP)/_(NPN) 1 ENG (R) (X) OUT ENG SYSTEM RECEIVE 2 SEQ CONT OUT (X) (Selectable with S301/RC-91) 2 ENG (R) (Y) OUT 0 dBu BALANCED 3 STAIR CASE OUT (X) *4 3 ENG (G) GND for ENG 4 STAIR CASE OUT (G) GND for STAIR CASE 4 ENG (T) (X) I
Resumen del contenido incluido en la página 14
1-4. Matching Connectors and Cables INCOM (5-pin, Female) Connector Connector/cable HDCU-950 1-569-370-12 PLUG, BNC or 5 1 RET IN (1-3) BELDEN8281 Cable or 4 2 3 SERIAL OUTPUT (1-2, MONI) equivalent SD SDI OUT (1-3) _____ EXT VIEW _____ (0 dBu = 0.775 Vrms) HKCU-953 HD SDI OUT (1-2) No. Signal Specifications MIC1/MIC2 1-508-083-00 XLR 3-pin female 1 INCOM (T) IN (Y) _20 dB (3-pin, Male) or CANNON XLR-3-11C 2 INCOM (T) IN (X) (CARBON MIC) equivalent _40 dB MIC REMOTE 1-506-582-11 D-sub 15-pin, ma
Resumen del contenido incluido en la página 15
1-5. Circuit Boards Layouts 1-5. Circuit Boards Layouts TX-83 board RX-67board SDI-70 board CN-2220 board HIF-5 board CN-2219 board AU-281 board VDA-61 board (HKCU-951) or DIF-124 board DIF-124 board or SDI-73 board (HKCU-953) CN-2227 board CN-2226 board CN-2224 board AT-149 board CN-2225 board MB-951 board AVP-4 board EN-145 board (HKCU-951) or DTX-1 board RC-91 board DRX-1 board RC-91 board or FC-88 board (HKCU-953) n To install the optional board is required depending on the system to be
Resumen del contenido incluido en la página 16
1-6. Setting of Switches on Boards 1-6. Setting of Switches on Boards 1-6-1. AT-149 Board AB C D E F G H J K 1 AT POWER S404 S409 S408 /1.001 S403 S410 S402 2 90H S406 S416 S412 REFERENCE REF IN S407 S417 UN LOCK 3 S427 HD REM BB S423 S424 H PHASE S405 STEP 4 S422 S421 COARSE S428 ADV 5 DELAY AT-149 board (A side/panel side) n . 404 (MARKER SEL) Sets the type of the aspect marker. Do not change the settings of the switches described “Factory use only” and unused switches. Setting switches Aspect
Resumen del contenido incluido en la página 17
S411 S413 1-6. Setting of Switches on Boards . S408 (MARKER REMOTE/LOCAL SEL) . S414 (FIBER/COAX-1/COAX-2 SEL) Selects either the HDCU-950 or the RCP/MSU connect- When S423-8 on the AT-149 board is set to ON, select ed outside in order to control the aspect marker and skin the camera signal reception mode of the HDCU-950. gate signal to be inserted in the HD SDI MONITOR When S423-8 on the AT-149 board is set to OFF output signal and in the PIX output signal that are output (factory setting), the
Resumen del contenido incluido en la página 18
1-6. Setting of Switches on Boards Factory setting : 60V (S418) . S423 (CCU MODE SET 1) Sets the CCU mode. INTR (S419) Factory setting : All OFF FORMAT S420 S418 S419 -1 : Sets the SD signal format when S420 on the AT-149 1080/60 (or 59.94) i 1.000 60V INTR board is set to position other than REMOTE. (or 1.001) ON : PAL (625/50) 1080/30 (or 29.97) PsF 1.000 60V PROG OFF : NTSC (525/60) (or 1.001) -2 : The remote control code of MIC GAIN can be 1080/50i 1.000 50V INTR switched to that of the HD
Resumen del contenido incluido en la página 19
1-6. Setting of Switches on Boards 1-6-2. AU-281 Board (Front Panel) . S4 (TALK GAIN) Sets the microphone input level according to the type of headset microphone to be connected to the INCOM connector on the front panel. DYNAMIC : When using a dynamic microphone (_60 dB) ECM : When using a electric condenser micro- POWER CABLE ALRAM CAM phone (_40 dB) OPEN MAIN CARBON : When using a carbon microphone SHORT (_20 dB) S1 Factory setting : CARBON S3 INCOM MIC-ON PROD S2 OFF PRIV . S5 (TALK DYNAMIC/E
Resumen del contenido incluido en la página 20
1-6. Setting of Switches on Boards 1-6-3. AVP-4 Board AB C D E F G H J K 1 S15 AVP POWER S16 INTERCOM S1 PGM1 2 MIX S501 S500 S11 PGM2 PGM1 LEVEL S14 S12 PGM2 LEVEL 3 SIDE S503 TONE 2WIRE CANCEL PROD S711 S502 S710 ENG 4 MIC LEVEL S103 S101 NORM S2 S610 MIC1 MIN S611 S102 S100 NORM 5 S3 MIC2 MIN AVP-4 board (A side/panel side) n . S11 (FP INCOM MODE SEP/MIX/OFF) Do not change the settings of the switches described Selects the receiving audio of the producer line (or “Factory use only”. engineer
