Resumen del contenido incluido en la página 1
EZ-45DP/EZ-55DP
DP SERIES II (DATA PORT)
1-Way Paging Remote Engine Starting & Keyless
Entry System with 5 Button Sidekick Remote Control
OPERATING INSTRUCTIONS
-PRIMARY: These are features that must be connected in order for the system to operate properly i.e.
Remote Start connections, Flashing lights, Brake Reset. For programming, the hood pin and program button
are required.
-OPTIONAL: These are features are to be connected only if desired or agreed upon by the custome
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS Operation Cautions & Warnings….………………..….…………………………………….……………….….………2 Remote Operation………………………………………………………………………………………………..…...….3 Remote Engine Starting ,Idle Down Mode, Infinity Run Mode, ………………………………………….…...…..4-7 Turbo Timer Mode……………………………….……………………………………...…………………….…..….…..8 Convenience and Safety Features…………………………….………………..………………………..….…..….9-10 Transmitter Programming….…………….………………………………………….……………….…..…….….....…11 2 Vehicle Operation.………………………………….………………...…
Resumen del contenido incluido en la página 3
REMOTE OPERATION OPERATION: BUTTON 1 (Lock Symbol): • Press and release to Lock doors. • Press and Hold for more than 3 seconds to activate #3 “Panic” feature. TRUNK BUTTON 2 (Unlock Symbol): • Press and release to Unlock doors. For EZ-55DP II only (Driver Door Priority Unlock) • Press 2 times for Driver Door Priority Unlock. #2 #1 BUTTON 3 (Trunk Symbol): LOCK UNLOCK • Press and Hold for ½ second or press twice to (AUX#2) activate trunk pop. (AUX#3) START BUTTON 4 (St
Resumen del contenido incluido en la página 4
REMOTE ENGINE STARTING REMOTE ENGINE STARTING - SUCCESSFUL START: 1) Press the remote start button for at least 1/2 second (Default) or twice if set for double press. 2) Parking lights flash once; return solid, and the Ignition/Acc circuits turn on. 3) After a few seconds the Starter Motor engages, Parking lights and Acc circuits will turn off while cranking. 4) Engine Starts and Runs. Parking Lights and Acc turn back on, Doors Lock. 5) Engine will remain running for programmed run tim
Resumen del contenido incluido en la página 5
REMOTE ENGINE STARTING Cont. ENTERING YOUR REMOTE STARTED VEHICLE: 1) With engine running, Remote Unlock system (If equipped) or open door with key. 2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset). 3) Turn Ignition to ON/RUN position, then press brake pedal to reset the Remote Starter & Shift out of park. 4) Remote starter will reset instantly when the brake is pressed. Parking lights will turn off and the ignition key is now controlling your vehicle.
Resumen del contenido incluido en la página 6
REMOTE ENGINE STARTING Cont. (IDLE DOWN MODE) IDLE DOWN MODE - EXITING THE VEHICLE: 1) With vehicle engine running with key, **press the Remote Start button for at least a 1/2 second or twice if set for double press. 2) Parking Lights will turn ON. 3) Doors will unlock, or if brake pedal is being depressed, doors will unlock when it is released. 4) Turn OFF Ignition and remove key. Engine should remain running. 5) Exit vehicle, then remote lock doors if desired. 6) Engine will remain
Resumen del contenido incluido en la página 7
REMOTE ENGINE STARTING Cont. (Infinity Run Mode) INFINITY RUN MODE – EXITING THE VEHICLE: 1) With vehicle engine running with the key, **press the Remote Start button for at least 1/2 second, pause a few seconds, then press and release the remote start button a second time. 2) Parking Lights will start flashing, and doors will unlock. 3) Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running. 4) The vehicle’s parking lights will flash for the programmed
Resumen del contenido incluido en la página 8
TURBO TIMER MODE (OPTIONAL) The optional Turbo Timer mode allows the EZEE START system to keep a Turbo or Turbo Diesel vehicle running for 1 to 5 minutes [selectively] after you remove the key, exit the vehicle, and lock the doors remotely. This is handy for turbo cool-down without the need for expensive turbo timers. This mode requires the use of an extra part called a momentary switch/button that is not included with the kit. Check with your installer about adding this feature. NO
Resumen del contenido incluido en la página 9
CONVENIENCE AND SAFETY FEATURES KEYLESS ENTRY (POWER DOOR LOCK CONTROL, Optional) This system enables you to remotely lock and unlock the vehicle’s doors (if equipped with power locks) via remote control for safety and convenience. Note: This feature may require extra labor and/or parts to install. Press the Lock or Unlock transmitter button as you leave or come near the vehicle. Parking lights will flash once for lock and twice for unlock. If vehicle is running by the remote start syst
Resumen del contenido incluido en la página 10
CONVENIENCE AND SAFETY FEATURES VALET MODE / STARTER DISABLE OVERRIDE Before servicing your vehicle or handing the keys over to a Valet we recommend putting the unit into valet mode. The remote start function WILL NOT operate when in Valet mode. To enter Valet mode, turn the key to the ON position, press and hold Program/Valet switch for 5-6 seconds. The LED will turn on solid and the system is now in valet. Perform this procedure again to exit of Valet mode. The keyless entry will s
Resumen del contenido incluido en la página 11
TRANSMITTER PROGRAMMING Note: All transmitter codes must be learned at time of programming!! The unit will learns up to 4 different transmitter codes. 1. Turn key to the ON position. 2. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times. 3. Press button #1 on the transmitter to be coded. You should get 2 light flashes indicating the unit is waiting nd for a 2 code, then press button #1 on the second transmitter, the unit will f
Resumen del contenido incluido en la página 12
2-VEHICLE OPERATION A single remote can control two different vehicles EZEE START systems installed. However, both systems must be the same type. EZ-45DP II/55DP II are only compatible with each other. Programming: nd You must first Programming your remote for 2 vehicle operation: nd (2 Vehicle Programming and Operation instruction): In step #4 of transmitter programming (see page 11) press and hold middle button #5 for 2 sec., then press the lock button, parking light will flash in
Resumen del contenido incluido en la página 13
TROUBLESHOOTING cont. NO RESPONSE FROM REMOTE TRANSMITTERS: (4 Parts) 1. Check for proper power/ground wiring connections at module. 2. Check Antenna Module connection. The antenna module included with this system must be plugged in. 3. Transmitters may need to be programmed to the unit. See transmitter programming steps on Page 11. 4. Check transmitter Batteries and replace if necessary. UNIT CRANKS VEHICLE BUT ENGINE NEVER STARTS: (2 parts) 1. In extreme cold or severe weather con
Resumen del contenido incluido en la página 14
REMOTE START DIAGNOSTICS If the system flashes the parking lights one to three times and doesn’t attempt remote, it means the following: 1 Parking Light Flash = Problem with Brake Switch. 2 Parking Light Flashes = Problem with Hood Switch. 3 Parking Light Flashes = Valet Service Mode. BATTERY REPLACEMENT To replace the battery: Simply remove the screws on back of the transmitter and open the case. Remove the battery and replace. The replacement battery for all transmitters is GP2
