Manual de instrucciones de Whirlpool W10184583A

Manual de instrucciones del aparato Whirlpool W10184583A

Aparato: Whirlpool W10184583A
Categoría: Secadora
Fabricante: Whirlpool
Tamaño: 3.25 MB
Fecha de añadido: 10/22/2013
Número de páginas: 36
Imprimir el manual

Descargar

¿Cómo se utiliza?

Nuestro propósito es proporcionarte el acceso más rápido posible a los contenidos incluidos en los manuales de instrucciones del aparato Whirlpool W10184583A. Utilizando la vista previa online, puedes ver rápidamente el índice de contenidos y pasar a la página donde encontrarás la solución a tu problema con Whirlpool W10184583A.

Para tu comodidad

Si ver los manuales de instrucción de Whirlpool W10184583A directamente en esta página no es cómodo para ti, puedes utilizar dos soluciones posibles:

  • Vista en pantalla completa – Para ver cómodamente los manuales de instrucciones (sin descargarlos en tu ordenador) puedes utilizar el modo de vista en pantalla completa. Para activar la vista del manual Whirlpool W10184583A en pantalla completa, utiliza el botón Pantalla completa
  • Descargar al ordenador – también puedes descargar el manual de instrucciones de Whirlpool W10184583A a tu ordenador y guardarlo en tu colección. Sin embargo, si no quieres ocupar espacio en tu dispositivo, siempre podrás descargarlo de ManualsBase.
Whirlpool W10184583A Manual de instrucciones - Online PDF
Advertisement
« Page 1 of 36 »
Advertisement
Versión impresa

Muchas personas prefieren no leer el documento en la pantalla, sino en versión impresa. La opción de impresión también está prevista y puedes utilizarla haciendo clic en el enlace más arriba - Imprimir el manual. No tienes que imprimir el manual completo de Whirlpool W10184583A, solo las páginas que elijas. Ahorra papel.

Resúmenes

A continuación encontrarás resúmenes de los contenidos incluidos en las páginas posteriores del manual de instrucciones para Whirlpool W10184583A. Puedes utilizarlos si quieres ver rápidamente el contenido que se encuentra en la siguientes páginas del manual.

Resúmenes de contenidos
Resumen del contenido incluido en la página 1

INSTALLATION INSTRUCTIONS
COMMERCIAL DRYER – Gas or Electric
INSTRUCTIONS POUR L’INSTALLATION D’UNE
SÉCHEUSE COMMERCIALE – À gaz ou électrique
Table of Contents/Table des matières . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
W10184582A
SP - W10184583A
www.whirlpoolcommerciallaundry.com

Resumen del contenido incluido en la página 2

TABLE OF CONTENTS TABLE DES MATIÈRES DRYER SAFETY............................................................................ 2 SÉCURITÉ DE LA SÉCHEUSE ..............................................22 INSTALLATION REQUIREMENTS .............................................. 5 EXIGENCES D’INSTALLATION................................................25 Tools and Parts .......................................................................... 5 Outillage et pièces ....................................

Resumen del contenido incluido en la página 3

WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, or to prevent property damage, personal injury, or death. – Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. – WHAT TO DO IF YOU SMELL GAS: Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Clear the room, building, or area of all occupants. • Immediate

Resumen del contenido incluido en la página 4

In the State of Massachusetts, the following installation instructions apply: n Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by the State of Massachusetts. n If using a ball valve, it shall be a T-handle type. n A flexible gas connector, when used, must not exceed 3 feet.  It is recommended that the owner post, in a prominent location, instructions for the customer’s use in the event the customer smells gas. This

Resumen del contenido incluido en la página 5

INSTALLATION REQUIREMENTS Tools and Parts Location Requirements Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed  8" (20 cm) or 10" (25 cm) Pipe wrench  8" (20 cm) or 10" (25 cm) adjustable wrench  Flat-blade screwdriver  Phillips screwdriver  Adjustable wrench that opens to 1" (25 mm) or 1" (25 mm) hex-head socket wrench  Level 5  ⁄16" socket wrench  Utility knife  Vent clamps  Pipe-joi

Resumen del contenido incluido en la página 6

Minimum Installation Clearances Product Dimensions 27" (686 mm) dryer 14" (356 mm) 27" (686 mm) max. 15" Closet (381 mm)* door ELECTRIC 14" 0" (35.6 cm) (0 mm) 37" BACK VIEW (940 mm) 0" (0 mm) 0" (0 mm) 1" (25 mm) 3 13" 6 ⁄4" 4" (102 mm) (330 mm) 3 (152 mm) 4 ⁄4" Recessed front view Closet side view dia. (121 mm) Additional clearances for wall, door and floor moldings may be required or if external exhaust elbow is used. GAS EXHAUST 3" (76 mm) 2 1 48 in 1 ⁄4" 2 (310 cm )* (32 mm) 1 29 ⁄4" (743 m

Resumen del contenido incluido en la página 7

Recommended Ground Method Electrical Requirements – Gas Dryer The dryer, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, latest edition, or Canadian Electrical Code, CSA C22.1, and all local codes and ordinances. IMPORTANT: The dryer must be electrically grounded in accordance with local codes and ordinances or, in the absence of local codes, with the National Electrical Code, ANSI/NF

Resumen del contenido incluido en la página 8

If using a power supply cord: Electrical Requirements – U.S.A. Only Use a UL listed power supply cord kit marked for use with It is your responsibility clothes dryers. The kit should contain:  A UL listed 30-amp power supply cord, rated 120/240 volt  To contact a qualified electrical installer. minimum. The cord should be type SRD or SRDT and be at  To be sure that the electrical connection is adequate and in least 4 ft (1.22 m) long. The wires that connect to the dryer conformance with the N

Resumen del contenido incluido en la página 9

If connecting by direct wire:  To supply the required 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply on a separate 30-amp Power supply cable must match power supply (4-wire or 3-wire) circuit, fused on both sides of the line. A time-delay fuse or and be: circuit breaker is recommended. Connect to an individual  Flexible armored cable or nonmetallic sheathed copper cable branch circuit. (with ground wire), protected with flexible metallic conduit. All  This dryer is equi

Resumen del contenido incluido en la página 10

Gas Supply Line Gas Supply Requirements Recommended method 1  Provide a gas supply line of ⁄2" rigid (IPS) pipe to the dryer location. Pipe joint compounds that resist the action of LP gas ®† must be used. Do not use TEFLON tape. With LP gas, 1 piping or tubing size can be ⁄2" minimum. Usually, LP gas suppliers determine the size and materials used in the system. Alternate method 3  The gas supply may also be connected using ⁄8" approved copper or aluminum tubing. If the total length of the su

Resumen del contenido incluido en la página 11

 Installed in a confined area: Exhaust hood must be at least 12" (305 mm) from the ground or any object that may be in the path of the exhaust (such as If the dryer is installed in a confined area such as a bathroom flowers, rocks, or bushes). or closet, provision must be made for enough air for combustion and ventilation. Check governing codes and If using an existing vent system, clean lint from the entire length ordinances or refer to the “Recessed Area and Closet of the system and make sure

Resumen del contenido incluido en la página 12

Keep air openings free of dry cleaning fluid fumes. Fumes create Multiple Dryer Venting acids which, when drawn through the dryer heating units, can damage dryers and loads being dried.  A main vent can be used for venting a group of dryers. The A clean-out cover should be located on the main vent for periodic main vent should be sized to remove 200 CFM of air per cleaning of the vent system. dryer. Large-capacity lint screens of proper design may be If an exhaust hood cannot be used: used in t

Resumen del contenido incluido en la página 13

INSTALLATION INSTRUCTIONS – GAS DRYER Make Gas Connection Complete Installation 1. With dryer in final position, place level on top of the dryer, first side to side; then front to back. If the dryer is not level, adjust the legs of the dryer up or down until the dryer is level. 1. Remove red cap from gas pipe. 2. Connect gas supply to dryer. Use pipe-joint compound resistant to the action of L.P. gas for gas connections. If flexible metal tubing is used, be certain there are no kinks. If necessa

Resumen del contenido incluido en la página 14

INSTALLATION INSTRUCTIONS – ELECTRIC DRYER 1. Disconnect power. Make Electrical Connection 2. Remove hold-down screw and the terminal block cover. Power Supply Cord Method – U.S. Only A D C B A. External ground conductor screw B. Tab C. Terminal block cover D. Hold-down screw 3 3. Assemble ⁄4" (19 mm) UL-listed strain relief (UL marking on strain relief) into the hole below the terminal block opening. Tighten strain relief screws just enough to hold the two clamp sections together. Install power

Resumen del contenido incluido en la página 15

Power Supply Cord, B A Four-wire electrical connection: 5. Remove the center terminal block screw. 6. Remove the appliance neutral ground wire C A from the external ground conductor screw. Fasten under center, silver-colored terminal block screw. G 7. Connect the ground wire of the power supply cord to the external ground B F C conductor screw. Tighten screw. D 8. Connect the neutral wire (white or center) of the power supply cord under the center D screw of the terminal block. Tighten screw. E

Resumen del contenido incluido en la página 16

Use this method where local codes permit connecting Power Supply Cord, neutral ground wire to neutral wire: A Three-wire electrical connection: B 5. Loosen or remove the center terminal F block screw. 6. Connect the neutral wire (white or center) of the power supply cord to the center, silver-colored terminal screw of the E terminal block. Tighten screw. 7. Connect the other wires to outer terminal A C block screws. Tighten screws. 8. Tighten strain relief screws. 9. Insert tab of the terminal b

Resumen del contenido incluido en la página 17

1. Disconnect power. 2. Remove hold-down screw and terminal block cover. Direct Wire Method – U.S. Only A D C B A. External ground conductor screw B. Tab C. Terminal block cover D. Hold-down screw 3 3. Install ⁄4" conduit connector into the hole below the terminal block opening. Connect flexible metallic conduit and tighten connector screw. Install direct wire cable through the flexible metallic conduit. B A C A. Conduit connector B. Dryer cabinet C. Connector screw 4. Complete installation foll

Resumen del contenido incluido en la página 18

Direct Wire, Use this method where local codes permit A Three-wire electrical connection: connecting neutral ground wire to B neutral wire: 5. Loosen or remove the center terminal E block screw. 6. Place the hooked end of the neutral wire (white or center) of the direct wire cable D under the center screw of the terminal block (hook facing right). Squeeze C hooked end together. Tighten screw. Three wire with ground wire: green or bare 7. Place the hooked ends of the other wire cut short. Wire is

Resumen del contenido incluido en la página 19

CHANGING TO A 30- OR 60-MINUTE TIMING CAM A B WARNING C D A. Ratchet tooth B. Timing cam Electrical Shock Hazard C. Drive lug D. V-shaped notch Disconnect power before making cam changes. Failure to follow these instructions can result in death 4. Insert a narrow, flat-blade screwdriver under the timing cam or electrical shock. near the clock shaft. Gently lift cam straight up and off shaft making sure that the V-shaped notch clears the ratchet tooth. You can install the 30-minute or 60-minute

Resumen del contenido incluido en la página 20

MAINTENANCE INSTRUCTIONS Maintenance instructions: If dryer does not operate, check the following:  Electric supply is connected.  Clean lint screen after each cycle.  Removing accumulated lint:  Circuit breaker is not tripped or house fuse is not blown. • From inside the dryer cabinet:  Door is closed.  Controls are set in a running or “ON” position. Lint should be removed every 2 years or more often, depending on dryer usage. Cleaning should be done  START/RESTART button has been pushed


Manuales de instrucciones similares
# Manual de instrucciones Categoría Descargar
1 Whirlpool 3395339 Manual de instrucciones Secadora 105
2 Whirlpool 240-volt Manual de instrucciones Secadora 61
3 Whirlpool 3396304 Manual de instrucciones Secadora 15
4 Whirlpool 3393 137 Manual de instrucciones Secadora 8
5 Whirlpool 3390148 Manual de instrucciones Secadora 7
6 Whirlpool 3397627C Manual de instrucciones Secadora 10
7 Whirlpool 240-VOLT ELECTRIC DRYER Manual de instrucciones Secadora 14
8 Whirlpool 3397617 Manual de instrucciones Secadora 5
9 Whirlpool 340 1094 Manual de instrucciones Secadora 34
10 Whirlpool 3405792 Manual de instrucciones Secadora 0
11 Whirlpool 3401092 Manual de instrucciones Secadora 0
12 Whirlpool 3401086 Manual de instrucciones Secadora 1
13 Whirlpool 3401011 Manual de instrucciones Secadora 2
14 Whirlpool 3402328 Manual de instrucciones Secadora 0
15 Whirlpool 3978909 Manual de instrucciones Secadora 1
16 ACS 882.00284.00 Manual de instrucciones Secadora 0
17 ACS 255 CMF (85 Manual de instrucciones Secadora 0
18 ACS 380 M3 /hr) Manual de instrucciones Secadora 0
19 Philips 1.07E+23 Manual de instrucciones Secadora 1
20 Philips 1.07E+31 Manual de instrucciones Secadora 3