Resumen del contenido incluido en la página 1
AD-410 Phase 7
Service Manual
American Dryer Corporation
88 Currant Road
Fall River, MA 02720-4781
Telephone: (508) 678-9000 / Fax: (508) 678-9447
E-mail: techsupport@amdry.com
www.amdry.com
102600DMG/calbert ADC Part No. 450051
Resumen del contenido incluido en la página 2
Retain This Manual In A Safe Place For Future Reference American Dryer Corporation products embody advanced concepts in engineering, design, and safety. If this product is properly maintained, it will provide many years of safe, efficient, and trouble-free operation. ONLY qualified technicians should service this equipment. OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the installation manual included with the dryer. The following “FOR YOUR SAFETY” caution must be po
Resumen del contenido incluido en la página 3
IMPORTANT YOU MUST DISCONNECT and LOCKOUT THE ELECTRIC SUPPLY and THE GAS SUPPLY or THE STEAM SUPPLY BEFORE ANY COVERS or GUARDS ARE REMOVED FROM THE MACHINE TO ALLOW ACCESS FOR CLEANING, ADJUSTING, INSTALLATION, or TESTING OF ANY EQUIPMENT per OSHA (Occupational Safety and Health Administration) STANDARDS. FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPOR AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. DO NOT DRY MOP HEADS IN THE DRYER. DO NOT USE DRYER IN THE P
Resumen del contenido incluido en la página 4
WARNING DRYER MUST NEVER BE OPERATED WITHOUT THE LINT FILTER OR SCREEN IN PLACE, EVEN IF AN EXTERNAL LINT COLLECTION SYSTEM IS USED. IMPORTANT PLEASE OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment and specified in the installation manual included with the dryer. The wiring diagram for the dryer is located in the front electrical control box area.
Resumen del contenido incluido en la página 5
Table of Contents AD-410 REFERENCE GUIDE (Basket [Tumbler] Section).................................3 AD-410 REFERENCE GUIDE (Base Section) ......................................................4 SECTION I SAFETY PRECAUTIONS ........................................................................................5 SECTION II ROUTINE MAINTENANCE....................................................................................7 A. Cleaning .........................................................
Resumen del contenido incluido en la página 6
SECTION VI PHASE 7 OPL SYSTEM DIAGNOSTICS ...........................................................97 A. Diagnostic (L.E.D. Display) Fault Messages .............................................................................. 97 B. Input/Output (I/O) Board Light Emitting Diode (L.E.D.) Indicators ............................................ 99 SECTION VII TROUBLESHOOTING .........................................................................................104 SECTION VIII PROCEDURE FOR FUN
Resumen del contenido incluido en la página 7
3 AD-410 Reference Guide (Basket [Tumbler] Section)
Resumen del contenido incluido en la página 8
4 AD-410 Reference Guide (Base Section)
Resumen del contenido incluido en la página 9
SECTION I SAFETY PRECAUTIONS CAUTION: The dryer should never be left unattended while in operation. WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury, or loss of life. WARNING: The dryer must never be operated with any of the back guards, outer tops, or service panels removed. PERSONAL INJURY or FIRE COULD RESULT. 1. DO NOT store or use gasoline or other flammable vapors and liquids
Resumen del contenido incluido en la página 10
WARNING: DO NOT dry mop heads. Contamination by wax or flammable solvents will create a fire hazard. WARNING: DO NOT use heat for drying articles that contain plastic, foam, sponge rubber, or similarly textured rubberlike materials. Drying in a heated basket (tumbler) may damage plastics or rubber and also may be a fire hazard. 7. A program should be established for the inspection and cleaning of lint in the burner area, exhaust ductwork, and area around the back of the dryer. The frequency o
Resumen del contenido incluido en la página 11
SECTION II ROUTINE MAINTENANCE A. CLEANING A schedule should be established for periodic inspection, cleaning, and removal of lint from various areas of the dryer, as well as throughout the ductwork system. The frequency of cleaning can best be determined from experience at each location. Maximum operating efficiency is dependent upon proper air circulation. The accumulation of lint can restrict this airflow. If the guidelines in this section are met, an ADC dryer will provide many years of
Resumen del contenido incluido en la página 12
WARNING: TO AVOID THE HAZARD OF ELECTRICAL SHOCK, DISCONTINUE ELECTRICAL SUPPLY TO THE DRYER. MONTHLY Empty the compressed air filter bowl. NOTE: REGULATOR PRESSURE IS TO BE SET AT 80 PSI (5.51 BARS). Clean any lint accumulation from the gas valve and burner area at the top of the dryer, the fan (impellor) motor, and the fan (impellor) bearings located in the dryer base. EVERY 6 MONTHS STEAM MODELS -Clean the steam coil fins. We suggest using compressed air and a vacuum cleaner with brush attac
Resumen del contenido incluido en la página 13
B. LUBRICATION MONTHLY The two (2) bearings that support the impellor/fan shaft must be lubricated. Use Shell Alvania #2 grease or its equivalent. Generically, this grease would be described as a NLGI Grade 2 multipurpose industrial grease with a lithium thickener and mineral base oil. EVERY 3 MONTHS The four (4) bearings that support the drive and idler shafts must be lubricated. Use Shell Alvania #2 grease or its equivalent. Generically, this grease would be described as a NLGI Grade 2 mu
Resumen del contenido incluido en la página 14
EVERY 6 MONTHS Change gear oil in basket (tumbler) shaft gear reducer. 1. Remove the drain plug (located at the bottom rear of the reducer). 2. After oil is completely drained, replace the drain plug. 3. Remove the vent plug and pour in 1.48 quarts (1.4 liters) of Mobil Oil DTE HH5G (I.S.O. viscosity grade 460), SAE 90, or its equivalent. C. ADJUSTMENTS 7 DAYS AFTER INSTALLATION and EVERY 6 MONTHS THEREAFTER Inspect bolts, nuts, screws, (bearing setscrews), nonpermanent gas connections (i.e., u
Resumen del contenido incluido en la página 15
SECTION III SPECIFICATIONS and DIMENSIONS A. SPECIFICATIONS (Gas and Steam Models) MAXIMUM CAPACITY (DRY WEIGHT) 410 lbs. 186.4 kg MINIMUM CAPACITY (DRY WEIGHT) 250 lbs. 113.39 kg BASKET (TUMBLER) DIAMETER 68-3/4” 174.62 cm BASKET (TUMBLER) DEPTH 66-3/8” 168.59 cm BASKET (TUMBLER) VOLUME 143 cu. ft. 4.05 cu. m. DRIVE MOTOR 7-1/2 HP 5.6 kw BLOWER MOTOR (GAS/STEAM) 15/25 HP 11.18/18.7 kw DOOR OPENING 40” wide x 50” high 101.6 cm x 127 cm DOOR SILL HEIGHT - LEVEL 39-3/4” 101 cm COMPRESSED AIR 80 P
Resumen del contenido incluido en la página 16
B. DIMENSIONS NOTE: ADC reserves the right to make changes in specifications at any time without notice or obligation. 12
Resumen del contenido incluido en la página 17
NOTE: ADC reserves the right to make changes in specifications at any time without notice or obligation. 13
Resumen del contenido incluido en la página 18
NOTE: ADC reserves the right to make changes in specifications at any time without notice or obligation. 14
Resumen del contenido incluido en la página 19
NOTE: ADC reserves the right to make changes in specifications at any time without notice or obligation 15
Resumen del contenido incluido en la página 20
SECTION IV INSTALLATION REQUIREMENTS Installation should be performed by competent technicians in accordance with local and state codes. In the absence of these codes, the installation must conform to applicable American National Standards: ANSI Z223.1- LATEST EDITION (National Fuel Gas Code) or ANSI/NFPA NO. 70-LATEST EDITION (National Electrical Code) or in Canada, the installation must conform to applicable Canadian Standards: CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91 (Liquid P
