Resumen del contenido incluido en la página 1
TX9000TS SERIES
®
SMART TEMP ELECTRONIC THERMOSTAT
INSTALLATION AND OPERATING INSTRUCTIONS
Easy as
1–2–3
Installs Easily Set Day & Time Choose Heat or Cool
Thank you for your confidence in our product. To obtain the best
IMPORTANT!
results from your investment, please read these instructions
thoroughly and acquaint yourself with your purchase before
• Please read all instructions carefully before beginning
installing your new thermostat. Then follow the installation
installation. Save them for f
Resumen del contenido incluido en la página 2
PROGRAM PERIOD DAY OF WEEK TIME TEMPERATURE MODE SWITCH LIGHT TX9000TS FAN SWITCH BUTTON 1. FEATURES Ask your dealer for other LUX thermostats to control those systems. • Extra Large Hybrid Touch Screen Display • Audible Touch Confirmation 3. INSTALLATION • EL Display Illumination Please read all instructions carefully before • Elegant Design beginning installation. • 7 Day Programming ® WARNING: • Energy Star Compliant • Your thermostat is a precision instrument. Please • 4 Periods Per Day hand
Resumen del contenido incluido en la página 3
• Do not install it where there are unusual heating 7. Press up on the conditions, such as: in direct sunlight; near a thumb latch at the lamp, radio, television, radiator, register, or bottom of thermostat fireplace; near hot water pipes in a wall; near a and separate the stove on the other side of a wall. body from its base. • Do not locate in unusual cooling conditions, 8. Hold the base against the wall. Route the wires such as: on a wall separating an unheated room; through the hole below th
Resumen del contenido incluido en la página 4
18. Verify that the system and its fan are 4.3.2. CHANGING OTHER SETTINGS operating properly. When set to a high If there are many choices for a value, usually that temperature, the heating system should provide setting will automatically advance by holding one warm air after a short time. Likewise a cooling of the arrow keys. Some settings though, must be system should provide cool air after a short time. changed one touch at a time. Usually sound from the furnace and air 4.4. NAVIGATION KEYS c
Resumen del contenido incluido en la página 5
4.9. SOFTWARE RESET • OVERRIDE will be automatically canceled at the start of the next program period. This reset is disabled while the touchscreen is locked. When activated it will reset all • OVERRIDE will be cancelled if the set programmable values and settings including the temperature is adjusted to its programmed value lock code and clock, to their default values. Then or if the units mode is changed. option switch positions will be read before 4.12. TEMPERATURE HOLD resuming normal opera
Resumen del contenido incluido en la página 6
• Set the mode switch to HEAT to program the convenient for you. unit for controlling your heater. Set the mode 5.2.1. COPY switch to COOL to program the unit for controlling COPY will copy the previous days programs into your air conditioner. the current day and advance the thermostat to the • Touch MENU. beginning of next day. • Use SCROLL to advance to SET/REVIEW HEAT 6. ADVANCED FEATURES PROGRAMS or SET/REVIEW COOL PROGRAMS. 6.1. FILTER USAGE MONITOR • Touch YES to begin scrolling through th
Resumen del contenido incluido en la página 7
• Use UP/DOWN arrows to adjust. • Touch YES to accept new code; ENTER OLD CODE will be visible. • Touch EXIT to return to main display. • Touch EXIT to return to main display. 6.3. TEMPERATURE CALIBRATION 6.5.2. TO LOCK SETTINGS • From the main menu touch MENU. • Touch OPEN LOCK SYMBOL on display LOCK • SCROLL to CAL TEMP. KEY? will appear. • Touch YES. CAL TEMP will be visible and • Touch YES. The display will now show a adjustment value will be flashing. CLOSED PADLOCK. • Use UP/DOWN arrows to
Resumen del contenido incluido en la página 8
• Maximum Smart Recovery time is one hour. from the wall by pressing up on the thumb latch at the bottom of thermostat and swinging the body • The Smart Recovery temperature set point must up and away to remove it from the wall. be achievable. If a desired smart recovery is repeatedly ignored by your thermostat. That is an 2. Remove the used batteries. See battery location indicator that you should modify your program so and polarity in figure on Page 12. ® ® that the recovery can be achieved wi
Resumen del contenido incluido en la página 9
COMMON FOR SYSTEM POWER COMMON FOR SYSTEM POWER COMMON FOR SYSTEM POWER COMMON FOR SYSTEM POWER 3.6. WIRING DIAGRAMS 2 + 3 WIRE HEATING SYSTEMS COOLING SYSTEMS JUMPER JUMPER PROVIDED PROVIDED W Y G B O RC RH C W Y G B O RC RH C W G RH Y G RH RC R R H F V C* F V 4 5 6 NOTE: "G" WIRE IS OMITTED FOR 2 WIRE SYSTEMS HEATING/COOLING SYSTEMS HEATING/COOLING SYSTEMS 5 + 6 Wire 2 Transformers 4 + 5 Wire 1 Transformers JUMPER JUMPER REMOVED PROVIDED W Y G B O RC RH C W Y G B O RC RH C W Y G B* O RC R
Resumen del contenido incluido en la página 10
2 WIRE, 24 VOLT AND MILLIVOLT HEAT ONLY SYSTEMS RC-RH SYSTEM COMMON JUMPER PROVIDED W Y G B O RC RH C WIRING DIAGRAM OPTIONAL NOTES 24 VOLT (APPLIES TO ALL HEAT HEAT TRANSFORMER DRAWINGS) 120 VAC * The DASHED wires are optional depending on your system type. * Verify whether “C”, “X” or “B” wires are connected to system 3 WIRE HEATING SYSTEM (3RD WIRE FOR FAN) RC-RH common. SYSTEM COMMON JUMPER PROVIDED * If “B” and “O” are W Y G B O RC RH C both present, it is likely that “B” is a system common
Resumen del contenido incluido en la página 11
4 WIRE HEATING AND COOLING SYSTEM RC-RH SYSTEM COMMON JUMPER PROVIDED W Y G B O RC RH C OPTIONAL 24 VOLT AC HEAT FAN SYSTEM COMPRESSOR TRANSFORMER 120 VAC 5 WIRE SYSTEM HEATING AND COOLING - 2 TRANSFORMERS RC-RH SYSTEM COMMON JUMPER REMOVED W Y G B O RC RH C OPTIONAL 24 VOLT 24 VOLT HEAT COOLING FAN COOL HEAT TRANSFORMER TRANSFORMER 120 VAC 120 VAC SINGLE STAGE HEAT PUMP SYSTEM RC-RH SYSTEM COMMON JUMPER PROVIDED W Y G B* O* RC RH C ADD OPTIONAL JUMPER 24 VOLT HEAT CHANGEOVER CHANGEOVER FAN SYST
Resumen del contenido incluido en la página 12
5.2. PROGRAMMING THE UNIT To ease reprogramming later, record your thermostat’s programs and settings in the table provided below. HEAT COOL DAY PERIOD TIME TEMP. TIME TEMP. MORN DAY THURS EVE HEAT COOL DAY PERIOD NIGHT TIME TEMP. TIME TEMP. MORN MORN DAY DAY MON FRI EVE EVE NIGHT NIGHT MORN MORN DAY DAY TUES SAT EVE EVE NIGHT NIGHT MORN MORN DAY DAY WED SUN EVE EVE NIGHT NIGHT JUMPER AND SWITCH POSITIONS OPTION ON C RHRC OBG Y W SWITCHES 1 2 3 4 GAS/ELECTRIC JUMPER HARDWARE RESET SOFTWARE RESET
