Manual de instrucciones de Emerson CF935BC00

Resumen del contenido incluido en la página 1

READ AND SAVE THESE INSTRUCTIONS
®
™
Model No.
ZURICH
CF935AB00 CF935ORB00
Ceiling Fan
CF935BC00 CF935PW00
Owner's Manual
CF935HTW00 CF935TG00
CF935OB00 CF935WB00
Net Weight: 21.1 Lbs.
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials.
You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to

Resumen del contenido incluido en la página 2

! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. 3. Be careful of

Resumen del contenido incluido en la página 3

This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan : Tools Needed for Assembly Installed Wire Length Wire Size A.W.G. One Phillips head screwdriver One stepladder Up to 50 ft. 14 One 1/4” blade screwdriver One wire stripper 50-100 ft. 12 Three wire connectors (supplied). ! WARNING MATERIALS Before assembly your ceiling fan, refer to section on Wiring outlet box and box connectors must be of type proper method of wiring your

Resumen del contenido incluido en la página 4

How to Put Your Ceiling Fan Together 1. Remove the hanger ball by loosening the setscrew 5. Make sure the grommet is properly installed in the in the hanger ball until the ball falls freely down the coupling cover, then slide the coupling cover on the downrod (Figure 1). Remove the pin from the downrod until it rests on the motor housing. Place downrod, then remove the hanger ball. Retain the the ceiling cover over the downrod. Be sure that pin and hanger ball for reinstallation in step 5. the c

Resumen del contenido incluido en la página 5

! WARNING SWITCH HOUSING ASSEMBLY To reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades. SWITCH HOUSING CONNECTOR 3/16-24 x 1/4" SLOTTED MOTOR PHILLIPS SCREWS (3) CONNECTOR SWITCH HOUSING BLADE WASHERS (3) MOUNTING SCREW (3) Figure 7 13.Remove the three switch housing mounting screws (Figure 7) from the switch housing plate. FAN BLADE Position t

Resumen del contenido incluido en la página 6

How to Hang Your Ceiling Fan OUTLET ! WARNING BOX The fan must be hung with at least 7' of clearance from floor to blades (Figure 9). CEILING TWO SCREWS SUPPLIED WITH HANGER OUTLET BOX BRACKET TAB Figure 10 AT LEAST Figure 2 7' 2. Carefully lift the fan and seat the hanger ball/ Figure 9 downrod assembly on the hanger bracket that was FLOOR just attached to the outlet box (Figure 11). Be sure the groove in the ball is lined up with tab on the ! WARNING hanger bracket (Figure 10). The outlet box

Resumen del contenido incluido en la página 7

BLACK AND BLUE 5. Secure the ceiling cover in place by sliding lock- FAN WIRES GROUND washers over the threaded studs and installing the WIRE two knurled knobs (supplied). (Figure 13.) Tighten LISTED the knurled knobs securely until the ceiling cover WHITE SUPPLY WIRE (NEUTRAL) CONNECTOR (3) fits snugly against the ceiling and the hole in the ceiling cover is clear of the downrod. Your fan is NOTE: CEILING COVER now wired to be turned on and off from the fan OMITTED FOR CLARITY. switch. GREEN WI

Resumen del contenido incluido en la página 8

! WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN. Trouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not start. 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit breakers. 2. Loose power line connections to the fan, or loose 2. Check line wire connections to fan and switch switch wire switch wire connections in the switch housing. connections in the switch housing.wire connections in