Manual de instrucciones de Desa K36EN

Manual de instrucciones del aparato Desa K36EN

Aparato: Desa K36EN
Categoría: Chimenea
Fabricante: Desa
Tamaño: 2.65 MB
Fecha de añadido: 6/5/2013
Número de páginas: 38
Imprimir el manual

Descargar

¿Cómo se utiliza?

Nuestro propósito es proporcionarte el acceso más rápido posible a los contenidos incluidos en los manuales de instrucciones del aparato Desa K36EN. Utilizando la vista previa online, puedes ver rápidamente el índice de contenidos y pasar a la página donde encontrarás la solución a tu problema con Desa K36EN.

Para tu comodidad

Si ver los manuales de instrucción de Desa K36EN directamente en esta página no es cómodo para ti, puedes utilizar dos soluciones posibles:

  • Vista en pantalla completa – Para ver cómodamente los manuales de instrucciones (sin descargarlos en tu ordenador) puedes utilizar el modo de vista en pantalla completa. Para activar la vista del manual Desa K36EN en pantalla completa, utiliza el botón Pantalla completa
  • Descargar al ordenador – también puedes descargar el manual de instrucciones de Desa K36EN a tu ordenador y guardarlo en tu colección. Sin embargo, si no quieres ocupar espacio en tu dispositivo, siempre podrás descargarlo de ManualsBase.
Desa K36EN Manual de instrucciones - Online PDF
Advertisement
« Page 1 of 38 »
Advertisement
Versión impresa

Muchas personas prefieren no leer el documento en la pantalla, sino en versión impresa. La opción de impresión también está prevista y puedes utilizarla haciendo clic en el enlace más arriba - Imprimir el manual. No tienes que imprimir el manual completo de Desa K36EN, solo las páginas que elijas. Ahorra papel.

Resúmenes

A continuación encontrarás resúmenes de los contenidos incluidos en las páginas posteriores del manual de instrucciones para Desa K36EN. Puedes utilizarlos si quieres ver rápidamente el contenido que se encuentra en la siguientes páginas del manual.

Resúmenes de contenidos
Resumen del contenido incluido en la página 1

DIRECT-VENT FIREPLACE
OWNER’S OPERATION AND
INSTALLATION MANUAL
For more information, visit www.desatech.com
For more information, visit www.desatech.com
NATURAL GAS
MODELS (V)K36EN
SERIES
PROPANE/LP GAS
MODELS (V)K36EP
SERIES
WARNING: If the information in this manual is not fol-
WARNING: Improper installation,
lowed exactly, a fire or explosion may result causing
adjustment, alteration, service,
property damage, personal injury, or loss of life.
or maintenance can cause injury
or property dama

Resumen del contenido incluido en la página 2

TABLE OF CONTENTS SAFETY INFORMATION 2 TABLE OF CONTENTS CLEANING AND MAINTENANCE ............................................ 26 SAFETY INFORMATION ............................................................ 2 PRODUCT IDENTIFICATION ..................................................... 3 TROUBLESHOOTING .............................................................. 27 LOCAL CODES ........................................................................... 3 REPLACEMENT PARTS ...................

Resumen del contenido incluido en la página 3

SAFETY INFORMATION 3 PRODUCT IDENTIFICATION 3 LOCAL CODES SAFETY INFORMATION PRODUCT IDENTIFICATION Continued Upper Louver Panel Flue Collar 5. This fireplace reaches high temperatures. Keep children and adults away from hot surfaces to avoid burns or clothing igni- tion. Fireplace will remain hot for a time after shutdown. Al- low surfaces to cool before touching. Nailing 6. Carefully supervise young children when they are in the room Flange with fireplace. 7. Do not modify this fireplace under

Resumen del contenido incluido en la página 4

PRODUCT FEATURES PRE-INSTALLATION PREPARATION 4 Location and Space Requirements PRODUCT FEATURES These are a few facts that can help you understand and enjoy your • Your fireplace is designed to be used in zero clearance installa- tions. Wall or framing material can be placed directly against direct-vent fireplace: any exterior surface on the back, sides, or top of your fireplace, • The venting system may be routed to the outside of your home except where standoff spacers are integrally attached

Resumen del contenido incluido en la página 5

PRE-INSTALLATION PREPARATION 5 Clearances 5 Framing and Finishing PRE-INSTALLATION PREPARATION Continued CLEARANCES 3 Minimum clearances to combustibles for the fireplace are as follows: 10 D /8" 5 15" C B 49 /8" Back, and sides 0"/mm 3 35 /4" A Perpendicular walls 6" (152mm) Floor 0"/mm Ceiling to louver opening 42" (1067mm) Front 36" (914mm) 3 E 13 /4" Top 0"/mm F 41" 1 Vent (See venting instructions for G 41 /4" Nailing Tabs specific venting clearances.) 1 68 /2" H Combustible material with a

Resumen del contenido incluido en la página 6

V G G V A D E V B L LOCATION OF TERMINATION CAP 6 LOCATION OF TERMINATION CAP N N H C I B Fixed V V Fixed Closed Openable Closed Openable F B V J G V X B B M A V K X TERMINATION CAP AIR SUPPLY INLET G GAS METER RESTRICTED AREA V X (TERMINATION PROHIBITED) A = clearance above grade, veranda, porch, deck, or balcony I = clearance to service regulator vent outlet [*72 inches (182.9cm) [*12 inches (30.5mc) minimum] minimum] B = clearance to window or door that may be opened J = clearance to non-mech

Resumen del contenido incluido en la página 7

VENTING INSTALLATION INSTRUCTIONS 7 Installation Precautions 7 VENTING INSTALLATION INSTRUCTIONS NOTICE: Read these instructions completely be- NOTICE: Failure to follow these instructions will void fore attempting installation. the warranty. These models are tested and approved for use with DESA (direct- INSTALLATION PRECAUTIONS vent) pipe components and terminations. • Wear gloves and safety glasses for protection The venting system must terminate on the outside of the structure and • Use extr

Resumen del contenido incluido en la página 8

VENTING INSTALLATION INSTRUCTIONS Installation Planning 8 VENTING INSTALLATION INSTRUCTIONS Continued INSTALLATION PLANNING Female There are two basic types of direct-vent installation: Locking Lugs • Horizontal Termination • Vertical Termination Male Horizontal Termination Installation Slots IMPORTANT: Horizontal square terminations require only inner portion of wall firestop. Horizontal installations using round termina- tion require exterior portion of wall firestop (see Figure 14, page 10).

Resumen del contenido incluido en la página 9

VENTING INSTALLATION INSTRUCTIONS 9 Installation Planning (Cont.) 9 VENTING INSTALLATION INSTRUCTIONS Continued WARNING: Do not recess vent termination into any wall. This will cause a fire hazard. Cut Siding Away to Fit Standoff 6. Noncombustible Exterior Wall: Position the horizontal vent 1 Standoff cap in the center of the 8 /2" round hole and attach to the exte- rior wall with four wood screws provided. Before attaching Wood Screw the vent cap to exterior wall, run a bead of non-hardening m

Resumen del contenido incluido en la página 10

VENTING INSTALLATION INSTRUCTIONS Installation Planning (Cont.) 10 VENTING INSTALLATION INSTRUCTIONS Continued 10. Place fireplace into position and shim with noncombustible ma- terial if needed. Nail or screw side flanges to framing to secure WARNING: Never run vent downward as this may unit in place. IMPORTANT: Make sure fireplace is level before cause excessive temperatures which could cause a securing. If fireplace is not level it will not work properly. fire. Operation of improperly install

Resumen del contenido incluido en la página 11

VENTING INSTALLATION INSTRUCTIONS 11 Installation Planning (Cont.) 11 VENTING INSTALLATION INSTRUCTIONS Continued Vertical (V) Required CORNER INSTALLATION Vertical (V) Vertical Pipe Horizontal (H) 1 Recommended Applications: *43 /2" min. None 30" max. 1 54 /2" min. 1 ft. 48" max. • Corner ground floor installation 1 66 /2" min. 2 ft. 60" max. 1 • Ground floor installation where pipe vents horizontally through wall 78 /2" min. 3 ft. 84" max. 1 (over 12" horizontal pipe) 90 /2" min. 4 ft. 20' max

Resumen del contenido incluido en la página 12

VENTING INSTALLATION INSTRUCTIONS Installation Planning (Cont.) 12 VENTING INSTALLATION INSTRUCTIONS Continued HORIZONTAL SYSTEM INSTALLATION USING TWO 90° ELBOWS The following configurations show the minimum vertical rise requirements for a horizontal system using two 90° elbows. Venting with Two 90° Elbows Horizontal (H ) + 1 Vertical (V) Horizontal (H ) Horizontal (H ) 1 2 45° Elbow 5' min. 2' max. 6' max. 6' min. 4' max. 12' max. 7' min. 6' max. 18' max. 8' min. 8' max. 20' max. 20' max. 8'

Resumen del contenido incluido en la página 13

VENTING INSTALLATION INSTRUCTIONS 13 Installation for Vertical Termination 13 VENTING INSTALLATION INSTRUCTIONS Continued 2. Assemble the desired lengths of pipe and elbows necessary to INSTALLATION FOR VERTICAL TERMINATION reach from the fireplace flue up through the firestop. Be sure Note: Vertical restrictor must be installed in all vertical installations. all pipe and elbow connections are fully twist-locked (see Fig- 1. Determine the route your vertical venting will take. If ceiling ure 8,

Resumen del contenido incluido en la página 14

VENTING INSTALLATION INSTRUCTIONS Installation for Vertical Termination (Cont.) 14 VENTING INSTALLATION INSTRUCTIONS Continued Venting with One 90° Elbow Vertical Termination Configurations Vertical (V) Horizontal (H) Figures 21 through 24 show four different configurations for verti- 5' min. 2' max. cal termination. 6' min. 4' max. 7' min. 6' max. Venting with Two 90° Elbows 8' min. 8' max. Vertical (V) Horizontal (H ) + 1 20' max. 8' max. Horizontal (H ) 2 45° Elbow Note: Install restrict

Resumen del contenido incluido en la página 15

VENTING INSTALLATION INSTRUCTIONS 15 Installation for Vertical Termination (Cont.) 15 High Altitude Installation VENTING INSTALLATION INSTRUCTIONS Continued HIGH ALTITUDE INSTALLATION Your DESA direct-vent fireplace has been tested and approved for elevations from 0-2000 feet (USA) and elevations from 0-4500 feet (Canada) . When installing this fireplace at an elevation above 2000 feet (in the USA), you may need to decrease the input rating by changing the existing burner orifice to a smaller si

Resumen del contenido incluido en la página 16

VENTING INSTALLATION INSTRUCTIONS Parts Lists for Venting Kits and Components 16 FIREPLACE INSTALLATION Check Gas Type Installing Optional Blower Accessory VENTING INSTALLATION FIREPLACE INSTALLATION INSTRUCTIONS CHECK GAS TYPE Continued Use proper gas type for the fireplace unit you are installing. If your gas supply is not correct, do not install fireplace. See retailer where PARTS LISTS FOR VENTING KITS AND you purchased the fireplace for proper fireplace according to your COMPONENTS gas type

Resumen del contenido incluido en la página 17

FIREPLACE INSTALLATION 17 Installing Optional Blower Accessory (Cont.) 17 FIREPLACE INSTALLATION Continued 4. Be certain that all wire terminals are securely attached to ter- minals on blower motor and that the screw retaining the green ground wire is tight. 5. Mount speed control box to switch bracket by placing the plastic control shaft forward through the opening in the switch bracket (see Figure 26). 6. While supporting speed control, secure control shaft with lock nut by pushing and turning

Resumen del contenido incluido en la página 18

FIREPLACE INSTALLATION Installing Optional Blower Accessory (Cont.) 18 Installing Gas Piping to Fireplace Location FIREPLACE INSTALLATION Continued 3. Place the blower against the lower rear wall of the firebox outer INSTALLING GAS PIPING TO FIREPLACE wrapper with the exhaust port directed upward and the thermodisc LOCATION positioned up near the fireplace bottom. The thermodisc must be oriented near the fireplace bottom as shown in Figure 28, page WARNING: A qualified service person must con-

Resumen del contenido incluido en la página 19

FIREPLACE INSTALLATION 19 Installing Gas Piping to Fireplace Location (Cont.) 19 Connecting Fireplace To Gas Supply Checking Gas Connections FIREPLACE INSTALLATION Continued CONNECTING FIREPLACE TO GAS SUPPLY CAUTION: Use only new, black iron or steel pipe. Internally-tinned copper tubing may be used in cer- Installation Items Needed tain areas. Check your local codes. Use pipe of 1/2" • 5/16" hex socket wrench or nut-driver inside diameter or greater to allow proper gas volume • sealant (resis

Resumen del contenido incluido en la página 20

FIREPLACE INSTALLATION Checking Gas Connections (Cont.) 20 Removing/Replacing Glass Door FIREPLACE INSTALLATION Continued 4. Check all joints of gas supply piping system. Apply noncorro- Pressure Testing Fireplace Gas Connections sive leak detection fluid to all joints. Bubbles forming show a 1. Open equipment shutoff valve (see Figure 33, page 20). leak. Correct all leaks at once. 2. Open propane/LP supply tank valve for propane/LP fireplace 5. Reconnect fireplace and equipment shutoff valve to


Manuales de instrucciones similares
# Manual de instrucciones Categoría Descargar
1 Desa (V)368ST Manual de instrucciones Chimenea 0
2 Desa (V)B36L Manual de instrucciones Chimenea 0
3 Desa (V)C36 Manual de instrucciones Chimenea 0
4 Desa (V)C36H Manual de instrucciones Chimenea 1
5 Desa (V)B36LI Manual de instrucciones Chimenea 0
6 Desa (V)C36I Manual de instrucciones Chimenea 1
7 Desa (V)B36I Manual de instrucciones Chimenea 1
8 Desa (V)C36L Manual de instrucciones Chimenea 0
9 Desa (V)B36 Manual de instrucciones Chimenea 4
10 Desa (V)C36LH Manual de instrucciones Chimenea 0
11 Desa (V)C36LI Manual de instrucciones Chimenea 0
12 Desa (V)CB36N(E) Manual de instrucciones Chimenea 0
13 Desa (V)CB36P(E) Manual de instrucciones Chimenea 0
14 Desa (V)DVF36 Manual de instrucciones Chimenea 2
15 Desa (V)G36 Manual de instrucciones Chimenea 0
16 Aarrow Fires Becton 7 mk3 Manual de instrucciones Chimenea 1
17 AEG Royal Belmont G20 Manual de instrucciones Chimenea 3
18 Austro Flamm Gussofen G3 Manual de instrucciones Chimenea 1
19 Aarrow Fires Becton Bunny Manual de instrucciones Chimenea 12
20 Avalon Stoves Victorian Lace DVS Face Black 95200132 Manual de instrucciones Chimenea 1