Resumen del contenido incluido en la página 1
Vision T9800HRT
Service Manual
1
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS SECTION 1: MAINTENANCE PROCEDURE …………………3 1. MAINTENANCE CHECK LIST………………………..............................4 2. TENSIONING THE BELT PROCEDURE………………………….……..5-6 3. DECK RE-WAXING PROCEDURE………………………………….……7 4. CLEAN THE GROOVES PROCEDURE…………….................................8 SECTION 2: WIRING DIAGRAM INSTRUCTION……………….9 1. T9800(TM87) MCB WIRING(FOR 110V / 220V)………………………..10 2. T9800(TM87) MCB WIRING DEFINITION OF PIN…………...………..11-12 3. T9800(TM87) CONSOLE WIRING…………………………
Resumen del contenido incluido en la página 3
SECTION 1 MAINTENANCE PROCEDURE 3
Resumen del contenido incluido en la página 4
MAINTENANCE CHECK LIST PREVENTIVE MAINTENANCE SCHEDULE Vision T9800 TREADMILL Item Daily Weekly Monthly Quarterly Biannual Annual Console Mounting Bolts Inspect Frame Clean Inspect Power Cord Inspect Display Console Clean Inspect Handrail & Handlebar Clean Inspect Front Roller Clean Inspect Rear Roller Clean Inspect Emergency Button Test Running belt Tension Inspect V Belt Clean Inspect Inspect & Deck Re-waxing Re-waxing Running Belt Inspect Clean Control Board (Vacuum) Motor Clean 4
Resumen del contenido incluido en la página 5
TENSIONING THE BELT PROCEDURE Caution: Over-tightening of the roller will severely shorten the life of the belt and may cause further damage to other components. Frequency: Every 1 months Running Belt: If when you plant your foot on the belt, you can feel a slipping sensation then the belt has stretched and is slipping across the rollers. This is a normal and common adjustment on a new treadmill. To eliminate this slipping, tension both the rear rollers Allen bolts 1/4 TURN as shown abov
Resumen del contenido incluido en la página 6
Drive Belt: If you have tensioned the running belt and are still experiencing a slipping, adjust the tension screw. Then try the treadmill again to check for slipping. 6
Resumen del contenido incluido en la página 7
DECK RE-WAXING PROCEDURE Caution: If deck is not to periodical add the waxing, between the deck and running belt will produce great friction make the deck and running belt to burn up and cut down the motor life . Frequency: Every 1 month Parts name: Silicon oil set Parts number: SZTM74SOS Price (USD): 0.6 Use time : 1 Procedure: 1. Loosen the tension bolts at both ends. 2. Pull the belt with your left hand and apply the silicon in the deck with your right hand. (The volume of silicon appl
Resumen del contenido incluido en la página 8
CLEAN THE GROOVES PROCEDURE Caution: If dirty grooves in the drive belt, motor and roller pulley, there will be noises while running. Frequency: Every 3 months Procedure: 1.Remove the drive belt and check the grooves in belt for dirt or dust and clean it. 2.Check the grooves in motor pulley for dirt or dust and clean it 3.Check the grooves in roller pulley for dirt or dust and clean it. 8
Resumen del contenido incluido en la página 9
SECTION 2 WIRING DIAGRAM INSTRUCTION 9
Resumen del contenido incluido en la página 10
T9800(TM87) MCB WIRING(FOR 110V / 220V) P7 P1 P6 J1 P4 J2 P3 P2 P7-------Motor wire P2--------SAFE SW (install software) P6------ on/off switch (power) J1--------RS232 (install software) J2-------Console cable P4--------Elevation cable P1-------Fan power P3--------Speed sensor (RPM) 10
Resumen del contenido incluido en la página 11
T9800(TM87) MCB WIRING DEFINITION OF PIN JP1:Elevation cable(6pin/AMP-350762-4) 1 4 5 2 3 6 P4 Pin Name Definition 1 ELVR_+5V Incline place signal test power 2 ELVR_POT Incline place signal 3 ELVR_GND Incline place signal test ground 4 UP Incline motor does move to up 5 DOWN Incline motor does move to down 6 COM Incline motor does turn on power 11
Resumen del contenido incluido en la página 12
J2: console cable 20 2 19 1 Pin Definition 1 Console ground 2 Motor Current 3 ELV REF GND 4 POT Wiper of ELV(0-5V) 5 ELV REF VOL.+5V 6 Speed. signal. (0-5V PULSE) 7 Console ground 8 Console ground 9 Console for MCB of the PWM signal 10 Console power 11 Console power 12 Console power 13 Console provide for incline motor UP signal 14 Console provide for incline motor DOWN signal 15 E_STOP 16 TX OUT(RESERVE) 17 RESERVE 18 RX IN(RESERVE) 19 ERR. SIG. 20 Console ground 12
Resumen del contenido incluido en la página 13
T9800(TM87) CONSOLE WIRING J15 J16 J1 J14 J13 J11 J5 J13-------Safety Pull Switch J15-------CSAFE 1 (Full csafe function) J11-------Safety Push Switch J16-------CSAFE 2 (Power only port) J5---------Main HR Interface J1---------RS232 (install software) J14-------Console cable 13
Resumen del contenido incluido en la página 14
T8900(TM87) CONSOLE WIRING DEFINITION OF PIN J14:20-pin console cable 19 1 20 2 J14 Pin Definition 1 Console ground 2 Motor Current 3 ELV REF GND 4 POT Wiper of ELV(0-5V) 5 ELV REF VOL.+5V 6 Speed. signal. (0-5V PULSE) 7 Console ground 8 Console ground 9 Console for MCB of the PWM signal 10 Console power 11 Console power 12 Console power 13 Console provide for incline motor UP signal 14 Console provide for incline motor DOWN signal 15 E_STOP 16 TX OUT(RESERVE) 17 RESERVE 18 RX IN(RESERVE) 19
Resumen del contenido incluido en la página 15
J13: Safety Pull Switch J11: Safety Push Switch J13 J11 2 1 2 1 Pin Name Definition Pin Name Definition 1 SS OUT Safe key 1 SS OUT Safe key 2 SS IN Console ground 2 SS IN Console ground J5: Main HR Interface 3 2 1 Pin Name Definition 1 HR2 Pulse Board signal 2 VCC Console power (+5V) 3 GND Console ground 15
Resumen del contenido incluido en la página 16
T9800(TM87) Electrical block diagram for 110V 16
Resumen del contenido incluido en la página 17
T9800(TM87) WIRING DIAGRAM INSTRUCTION for 110V 17
Resumen del contenido incluido en la página 18
T9800(TM87) Electrical block diagram for 220V 18
Resumen del contenido incluido en la página 19
T9800(TM87) WIRING DIAGRAM INSTRUCTION for 220V 19
Resumen del contenido incluido en la página 20
SECTION 3 CONSOLE FUNCTIONAL FLOW DIAGRAM 20
