Resumen del contenido incluido en la página 1
Frigidaire Side Burner
Built-In Usage
USE AND CARE MANUAL
FOR OUTDOOR USE ONLY
MADE IN THE USA
Resumen del contenido incluido en la página 2
General Safety Instructions IMPORTANT SAFETY INFORMATION - Read this manual carefully before using your grill to reduce the risk of fire, burn hazard or other injury. - Extreme care should be used because of the high temperatures produced by this appliance. CHILDREN SHOULD NOT BE LEFT UNATTENDED IN AN AREA WHERE THE GRILL IS BEING OPERATED. - This appliance must be kept clear from combustible materials, gasoline or other flammable vapors and liquids. Do not allow flammable materials to come
Resumen del contenido incluido en la página 3
Built-In Instructions The Frigidaire side burner is designed to be installed as a built-in side burner, in conjunction with a Frigidaire & Frigidaire Gallery grills. If installed as a built-in Grill, the Grill surround must be constructed of Non-combustible material. PLANNING AND DESIGN Start by identifying the number and size of components you want to include in your outdoor cooking center. Countertops must be constructed of non-combustible, outdoor-safe materials. Consider out- door lightin
Resumen del contenido incluido en la página 4
Built-In Instructions Additional Requirements: • If using a backsplash apron or rear wall, locate electrical service on the left hand side for rotisserie motor construc- tion. • A minimum clearance of 12” from the back of the outdoor cooking center must be maintained between the grill and any combustible construction such as wood siding of residence, 3” minimum for non-combustible construction. • The side vents on this unit can be covered for built in installations without danger of fire or with
Resumen del contenido incluido en la página 5
Natural Gas Installation 1. Under the grill, remove the NG gas regulator assembly from the main gas pipe. Once the NG gas regulator is removed, the main gas pipe will be showing under grill. (See Fig 1) Fig. 1 2. Using pipe sealant, attach the “T” Fitting to the main gas pipe coming out of the bottom of the grill. (See Fig 2) 3. Using pipe sealant, attach a 3/8” flared fitting to the side of the “T” fitting. (See Fig 3) 4. Attach the one end of the flex line to the fitting on the side of the
Resumen del contenido incluido en la página 6
LP Side Burner Conversion Underside of 1. Loosen the flex line attached to the side burn- right side er valve using an adjustable wrench. (See Fig. burner shelf 1) Fig 1 2. Remove the flex line completely from the side burner valve. (See Fig. 2) Flex Line 3. Remove the control knob from the front of the Valve Assembly side burner. (See Fig. 3) 4. Remove the screw holding the bezel in place on the side burner and remove bezel from front of side burner. (See Fig. 4) Fig 2 5. Grasp and remove NG va
Resumen del contenido incluido en la página 7
LP Side Burner Conversion 7. Reattach bezel and screw new LP valve onto front of side burner. (See Fig 4, again) 8. Reattach the flex line to the LP valve assem- bly and tighten securely. (See Fig. 7 Fig 7 9. Reattach the control knob onto the manifold stem. (See Fig. 3, again) Flex line attached 10. Looking down at top of side burner, use a Top of Side Burner 7mm nut driver to remove the NG. (See Fig. Looking down 8) Fig 8 16. Install the new LP orifice (See Fig. 9) NG orifice 17. From the bott
Resumen del contenido incluido en la página 8
LP Grill Conversion IMPORTANT: Make sure you have converted the side burner to Liquid Propane prior to completing the following steps. LP hose/ 1. Remove the LP gas hose assembly from the regulator Fig. 12 flare fitting. (this has the regulator attached to supplied with grill. it.) (See Fig. 12) 2. Using an adjustable wrench remove the flare fitting coming out of the bottom of the grill.Once the flare fitting is removed the main gas pipe will be showing under grill. (See Fig. 13) 4. Using p
Resumen del contenido incluido en la página 9
Installation Instructions Tools Required: Adjustable wrench, flat head screwdriver and a 1/4” socket wrench Please use the built in information on the following pages for the exact dimensions needed to fit the side burner into the structure. Once installed into the structure use the following steps to complete the side burner installation. INSTALLATION OF SIDE BURNER PARTS 1. Install burner into side burner tray lining up the three cutouts on the underside of the burner. (See Fig. 1) 2. Instal
Resumen del contenido incluido en la página 10
Lighting The Side Burner LEAK TESTING Make sure all burners are turned to “OFF”. Turn on the gas at the cylinder (LP models) or main valve (Natural models). DO NOT turn on the side burner. Perform a leak test at all connections and fit- tings by spraying a 50/50 solution of water and soap. If any bubbles appear, correct the leak before attempting to light the grill or side burner. LIGHTING INSTRUCTIONS Push and turn the control knob to the “HIGH”position and immediately press and hold the elec
Resumen del contenido incluido en la página 11
Warranty LIMITED LIFETIME WARRANTY Electrolux Icon Grills have a limited lifetime warranty on all stainless steel panels, a limited 3 year warranty on stainless steel burners, including labor within one year of the date of purchase; and a limited 1 year warranty on all other parts, labor included. In the U.S.A., your appliance is warranted by Electrolux Home Products North America. We authorize no person to change or add to any of our obligations under this warranty. Our obligations for service
