Resumen del contenido incluido en la página 1
XQG50-600TXB
XQG50-600SW
Automatic Drum Washing Machine
Table of Contents
Before using
Names of Parts--------inside front cover
Matters Needing Attention------------1-3
Installation--------------------------------4-5
Control Panel-------------------------------6
Operational Functions----------------6-7
During using
Program Selection------------------------8
Preparation---------------------------------9
Washing Methods--------------------10-11
Maintenance
Maintenance --------------------------
Resumen del contenido incluido en la página 2
Names of Parts Detergent distributor Top Operation button Door Program knob Porthole Temperature knob Power supply cable Earth terminal Drainage hose clip Packing bolt (3) Back plate screw (3) Drainage hose Back plate Caution and Warning symbols For your safety, any instructions in this manual with this “Warning” sign shall be strictly followed. For your safety and to prevent damages to the washing machine, any instructions in this manual with this “Stop” sign shall be strictly followed. This
Resumen del contenido incluido en la página 3
Matters Needing Attention ===Safety 2. Hold the plug and not the electric cable 1. A separate earthed socket is required when unplugging the washing machine. for the power supply. After installation of the washing machine,the power plug should be accessible during the normal wash. 3. Fuses in the power circuit should be rated 4. For your safety, dry hands before touch- for 15A. Refer to a washing machine techni- ing the washing machine and wear appropri- cian or a Haier designated service point
Resumen del contenido incluido en la página 4
Matters Needing Attention Wiring Circuit 9. The washing machine should be place in 8. The washing machine must not be used in a well ventilated area maintaing a space the open or in area of high moisture as water between walls or furniture. droplets may form on electrical components, Air dry the appliance if the washing machine components become wet. 10. Keep away from heat sources and direct 11. During installation, ensure that the electric sunlight to prevent plastic and rubber com- cable is
Resumen del contenido incluido en la página 5
Matters Needing Attention Technical Specification 4. Do not wash foam rubber or similar sponge 3. Never place heavy objects ,a heating materials. Model applianceor a water container on the top panel Item XQG50-600TXB/XQG50-600SW of the washing machine. Power supply 220V~(50Hz) 10 Maximum working current (A) Water pressure (MPa) 0.05 P 1 IPX4 5. Before washing, do up zippers, buttons , 6. Do not open the detergent box during Washing power
Resumen del contenido incluido en la página 6
Trouble shooting Installation The following circumstances do not constitute problems. Do not contact the As shown in figure1 remove all the packing materials maintenance service until the problem has been confirmed. (including the foam base). Problem Possible Cause Poor connection to power supply Power failure The washing machine fails to Door is not properly closed operate Fig 1 Machine has not been switched on Check attachments and materials. Water is not turned on W
Resumen del contenido incluido en la página 7
Installation Maintenance Connection of water inlet hose and washing machine 1. Turn of the water and electricity supply 2. Unplug the machine during cleaning and after every wash. Open the door to pre- maintenance. Use a soft cloth dampened with vent the formation of moisture and odors. soapy liquid to clean the machine case and rub- If the washing machine is left idle for a long ber components. Do not use corrosive or abra- period, drain any remaining water in the sive chemicals or solvents. m
Resumen del contenido incluido en la página 8
Washing Methods Control Panel 4. Washing temperature Setting C DE F Set the washing temperature as required, otherwise, set at position * when heating is not needed. 5. Selecting the function button Select function buttons as required (refer to the directions printed on the control panel) , otherwise keep all the button released. G B A C F DE 6. Washing XQG50-600SW Press the power button and the washing machine will automatically commence the pro- grammed washing process. 7. End G B A Wait 2-3
Resumen del contenido incluido en la página 9
Operational Functions Washing Methods 1. Laundry loading Reference loading Evenly load the laundry in the D No spin button =Overalls =Jeans (800g) washing machine and then tightly (cotton 950g) close the door of the washing When this button is pressed, the spin cycle will be spared but water Pajamas (200g) machine drain is still available. This function is useful for hard ironing fabrics, =Blended Note: 1) When first using the such as chemical fiber and wool fabrics. fabric clothes washi
Resumen del contenido incluido en la página 10
Preparation Program Selection 2. Water supply 1. Power supply Turn on the tap ensure that the water is clear. Plug in the power supply Caution: Before staring the washing machine turn on the 220V~/50Hz. water faucrt to ensure that the water faucet and the water inlet hose are connected correctly and do not leak. 3. Laundry treament 4. Detergent selection Only special low foam detergent =sort out clothes according to type and extent of dirt. should be used in automatic There are three types of
