Resumen del contenido incluido en la página 1
PRODUCT NUMBERS
CERATRONIC™
Proximity Faucet with Touch-Free
6058.105
6058.102
Temperature Control
Product No.'s & Options 1
Specifications
2
How to Install 2-3
Electrical Hook-up 4
Operation 5-6
Certified to comply with ASME A112.18.1M
Maintenance 6-8
© 2006 American Standard
M968857 REV.1.2
FAQ,s 8
Replacement Parts 9
NOTE TO INSTALLER: Please give this manual to the customer after installation.
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
custo
Resumen del contenido incluido en la página 2
Base P r oduct Deck Plate Remote Control How to order the Selectronic Product Base Product Deck Plate (optional) Remote Control 1. Choose Power Supply • Single Hole Sink • 1 and 3 Hole Sinks 2. Choose Desired Spout • Hot and Cold Inlets • Hot and Cold Inletst Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. All American Standard Faucets Are
Resumen del contenido incluido en la página 3
183mm Roughing-in Dimensions (7-3/16) 190mm (7-7/16) GENERAL DESCRIPTION: 132mm 143mm Electronic faucet with proximity operation. Colored (5-3/16) (5-5/8) LED's signal temperature change mode. Vandal 55mm D. resistant solid brass construction single post mounting. (2-3/16) Operates on AC permanent power. Water pressure 25mm MAX. range from 20 to 80 psi. In-line strainer for solenoid is (1) 381mm integral. Single inlet 3/8 compression, built-in checks, (15) 270mm MAX. and flexible stainless
Resumen del contenido incluido en la página 4
MOUNT ENCL 2 OSURE; Fig. 2 Fig. 2 LAVATORY RIM OR MOUNTING SURFACE 1. Determine location of ENCLOSURE (1). It must be located with-in the 14" (356mm) by 21" (533mm) shaded area shown in Fig. 2 in order for electrical 14" (356mm) connections from the spout assembly to be made. ENCLOSURE NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance SUPPLIES MOUNTING 1 HOLES between wall supply and ENCLOSURE (1) must be 2-3/4" taken into consideration. (71mm) 1524mm (60) WASTE 2. Remove 4 screws from COVER
Resumen del contenido incluido en la página 5
Fig. 1 3 ELECTRICAL INSTALLATION 1 2 ELECTRICAL 1 1. Remove ENCLOSURE COVER (1). Fig. 1. 2. Remove CIRCUIT BOARD (2) from ENCLOSURE (3). (May have to pull cord of power supply through). Fig. 1. 3. Feed the WIRE CONNECTORS (4) through the top of ENCLOSURE (3). Fig. 1b. 4. Remove SPLIT PLUG (5) from GROMMET (6). Fig. 1b Fig. 1c Insert the gray SENSOR WIRE (7) and YELLOW and 6 3 GREEN CONNECTOR WIRES (8) into SPLIT PLUG (5). Leave 4” of wire from end of SPLIT PLUG (5). Fig. 5 1c. Feed W
Resumen del contenido incluido en la página 6
Fig. 1 OPERATION BLUE RED SENSOR HAND WASH SENSOR OPERATION; 1 SENSOR Fig. 1 When the Sensor detects a user, the water immediately starts to flow. Water flow will stop Two seconds after user is out of sensor range. The off delay allows the user to comfortably move his hands without the flow cycling on to off. As a precaution, a safety timer will turn off the water, after the sensor has been blocked for 59 seconds. The water will stay off until the blockage is removed from the detecti
Resumen del contenido incluido en la página 7
F Fig. ig. 2 3 Fig. 3a 3 HOW TO SET DEFAULT ADJUST HOT ADJUST RED SENSOR R RED SENSOR ED SENSOR COLD TEMPERATURE Fig. 3 B BLUE BLUE LUE SENSOR SENSOR SENSOR Note: The factory setting of the Default Temperature is at a position of even amounts of hot and cold water flows. This setting can only be changed within the first 15 minutes of switching on the power. 1. Remove the power to the faucet by unplugging the Power Supply from the wall outlet. Wait 60 seconds, and then plug the Power Sup
Resumen del contenido incluido en la página 8
HOW TO CLEAN FILTER; Fig. 2 2 Fig. 2 Before opening ENCLOSURE CAUTION disconnect AC power supply. 1. Remove ENCLOSURE COVER. 2. Close SUPPLY STOPS. 1 Note: Keep water flowing out of faucet while shutting off. CLEAN 4. Unthread STRAINER (1) using a 7/16" socket. SCREENS 1 5. Pull out the STRAINER (1) and clean with an old toothbrush. Rinse thoroughly with water. INSTALL 6. Install the STRAINER (1) back in its place and REMOVE tighten with a 7/16" socket. Caution: do not over tighten strain
Resumen del contenido incluido en la página 9
GENERAL CLEANING; Fig. 4 4 Fig. 4 1. For general cleaning use a damp, soft cloth to clean the spout and the sensor. 2. For cleaning dirt use a soft cloth with diluted dish washing detergent. Wipe the area using a wet cloth and dry using a soft cloth. CAUTION Do not scratch the sensor when cleaning. Avoid using anything that may scratch the spout surface. Never use polishing power, detergent or a nylon scrub brush. They will damage the surface of the spout or Sensor. FAQ'S Q: Why has the
Resumen del contenido incluido en la página 10
CERATRONIC LAVATORY FAUCETS A960215-0070A PRODUCT NUMBERS SENSOR COVER (BLUE) 6058.105 A960217-0070A TEMPERATURE 6058.102 A960216-0070A SENSOR KIT SENSOR COVER (RED) Replace the "YYY" with M923827-YYYOA appropriate finish code 2.2 GPM AERATOR CHROME 002 066508-YYYOA 0.5 GPM AERATOR A960218-0070A SCREW KIT 605P400 A963103-0070A A960219-0070A SCREW SENSOR KIT M962411-0070A 605P800 MOUNTING KIT 044912-0070A MOUNTING NUT A923672-0070A A960221-0070A FAUCET SUPPLY WIRE COVER
Resumen del contenido incluido en la página 11
M968857 REV.1.2
