Resumen del contenido incluido en la página 1
122 135
Hawkins
44 in Ceiling Fan
Owner’s Manual
Hawkins
Ventilador de Techo de 1,12 m
Manual del Propietario
Resumen del contenido incluido en la página 2
Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. 44” Hawkins Ceiling Fan by Hampton Bay Date Purchased Table of Contents Store Purchased Safety Rules . . . . . . . . . . . . . . . . . . . . 1 122-135 Unpacking Your Fan . . . . . . . . . . . . . . 2 UL Model No. Installing Your Fan . . . . . . . . . . . . . . . 3 Installing the Light Kit. . . . . . . . . . . . . 8 Serial No. Operating Your Fan . . . . . . . . . . . . .
Resumen del contenido incluido en la página 3
Safety Rules - Read and Save These Instructions 1. To reduce the risk of electric shock, insure electricity has been turned off 10. After making electrical connections, spliced conductors should be turned at the circuit breaker or fuse box before beginning. upward and pushed carefully up into outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding 2. All wiring must be in accordance with the National Electrical Code conductor on one side of the ou
Resumen del contenido incluido en la página 4
Unpacking Your Fan Unpack your fan and check the contents. You should have the following items: AB 2 5 8 3 6 1 CD 9 4 7 10 1. Set of blades (5) 6. Light kit A. Blade Attachment Hardware (16 Screws with Fiber Washers) 2. Mounting bracket 7. Glass shade 3. Fan motor assembly 8. Pull chains and fobs (2) B. Electrical Hardware (3 Plastic Wire Nuts) 4. Motor housing 9. 40 Watt candelabra bulbs (3) 5. Blade arms (5) 10. Extra switch housing cover C. Light Kit Hardware (Metal Nut, Glass Cap, Decorative
Resumen del contenido incluido en la página 5
Installing Your Fan Figures 1 and 2 are examples of different ways to Tools Required mount the outlet box. Phillips screwdriver, straight slot screwdriver, adjustable wrench, step ladder, and wire cutters. Outlet Box Mounting Options Outlet Box If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect Figure 3 the power by removing fuses or turning off circuit breakers. To hang your fan where there is an existing fixture Figure 1 but no ceiling joi
Resumen del contenido incluido en la página 6
1. Connect the ground cnductor of the 120V Hanging the Fan supply (this may be a bare wire or a wire with green colored insulation) to the green ground REMEMBER to turn off the power. Follow the lead(s) of the fan (Figure 6). steps below to hang your fan properly. 1. Attach the mounting bracket to the outlet box 2. Connect the fan motor white wire to the supply with two screws and washers provided with the white (neutral) wire using a wire nut. (Figure outlet box. Make sure the bracket i
Resumen del contenido incluido en la página 7
WARNING Finishing the Fan TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK. DO NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE. Installation Studs 1. Move fan into position over the four mounting studs and secure with the provided washers and SUPPLY CIRCUIT nuts (Fig. 7). Ground 2. Raise the motor housing up against the Conductor mounting bracket, the four supports inside the housing should be placed against the four studs on mounting bracket, twist the housing Outlet Box clockw
Resumen del contenido incluido en la página 8
Attaching the Fan Blades Screws with Fiber Washers Motor Step 1. Attach blades to blade arms using three screws with fiber washers. (Fig. 9) Start a screw Tab into the blade arm, do not tighten. Repeat for the 2 remaining screws and washers. Blade Assembly Slot Step 2. Tighten each screw securely starting with the center screw. Make sure the blade is straight. Repeat steps for the remaining blades. Blade Blade Arm Step 3. Fasten the blade assemblies to the motor housing by lining up the sl
Resumen del contenido incluido en la página 9
Blade Balancing The following procedure should correct most fan wobble. Check after each step. Touching Ceiling 1. Check that all blade and blade arm screws are secure. 2. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades. Measure from a point on the center of each blade to the point on the ceiling. Measure this distance as shown in Figure 11. Rotate the fan until the next blade is posit
Resumen del contenido incluido en la página 10
NOTE Fan without Light Kit Installing the MAKE SURE TO LEAVE ENOUGH SPACE BETWEEN THE FAN PULL CHAIN AND THE (Optional) BULBS SO THE CHAIN DOESN'T RUB AGAINST Light Kit ANY OF THE BULBS. Your fan is designed with light kit, in case you intend to install the fan without light kit, attach the NOTE NOTE switch housing cover to the switch housing with BEFORE STARTING INSTALLATION, DISCONNECT LIGHT BULBS HAVE NO WARRANTY; CAN BE the screws provided. (Fig. 13) THE POWER BY TURNING OFF THE C
Resumen del contenido incluido en la página 11
Operating Your Fan NOTE WAIT FOR FAN TO STOP BEFORE REVERSING Warm weather - (Counter Clockwise Direction) THE DIRECTION OF THE BLADE ROTATION. A downward air flow creates a cooling effect as shown in Figure 14. This allows you to set your air Turn on the power and check the operation of the conditioner on a higher setting without affecting fan. The pull chain controls the fan speed as your comfort. follows: 1 pull - High 2 pulls - Medium 3 pulls - Low 4 pulls - Off. Figure 14 Light kit pul
Resumen del contenido incluido en la página 12
Care of Your Fan Troubleshooting Here are some suggestions to help you maintain PROBLEM SOLUTION your fan. Fan will not start 1. Check main and branch circuit fuses or breakers. 1. Because of the fan's natural movement, some 2. Check line wire connections to the fan and switch wire connections may become loose. Check the connections in the switch housing. support connections, brackets, and blade attachments twice a year. Make sure they are Fan sounds noisy 1. Make sure all motor housing s
Resumen del contenido incluido en la página 13
Specifications FAN SIZE SPEED VOLTS AMPS WATTS RPM CFM N.W. G.W. C.F. LOW 0.19 13 76 1540 7.4 kgs 8.3 kgs 44” MED. 120 0.31 28 123 2809 1.70’ (16.2 Ibs) (18.3 Ibs) HIGH 0.43 51 170 4286 These are approximate measures. They do not include Amps and Wattage used by the light kit . 11
Resumen del contenido incluido en la página 14
Lifetime Limited Warranty (lifetime warranty on motor) The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time You must present a copy of the original purchase receipt to obtain warranty of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser. service. Hampton Bay also warrants that all other fan parts, excluding any glass or acrylic blades, to be free from defects in workmanship and materi
