Manual de instrucciones de 321 Studios Oil Furnace FLR110D48E

Manual de instrucciones del aparato 321 Studios Oil Furnace FLR110D48E

Aparato: 321 Studios Oil Furnace FLR110D48E
Categoría: Máquina de café
Fabricante: 321 Studios
Tamaño: 0.92 MB
Fecha de añadido: 9/9/2014
Número de páginas: 39
Imprimir el manual

Descargar

¿Cómo se utiliza?

Nuestro propósito es proporcionarte el acceso más rápido posible a los contenidos incluidos en los manuales de instrucciones del aparato 321 Studios Oil Furnace FLR110D48E. Utilizando la vista previa online, puedes ver rápidamente el índice de contenidos y pasar a la página donde encontrarás la solución a tu problema con 321 Studios Oil Furnace FLR110D48E.

Para tu comodidad

Si ver los manuales de instrucción de 321 Studios Oil Furnace FLR110D48E directamente en esta página no es cómodo para ti, puedes utilizar dos soluciones posibles:

  • Vista en pantalla completa – Para ver cómodamente los manuales de instrucciones (sin descargarlos en tu ordenador) puedes utilizar el modo de vista en pantalla completa. Para activar la vista del manual 321 Studios Oil Furnace FLR110D48E en pantalla completa, utiliza el botón Pantalla completa
  • Descargar al ordenador – también puedes descargar el manual de instrucciones de 321 Studios Oil Furnace FLR110D48E a tu ordenador y guardarlo en tu colección. Sin embargo, si no quieres ocupar espacio en tu dispositivo, siempre podrás descargarlo de ManualsBase.
321 Studios Oil Furnace FLR110D48E Manual de instrucciones - Online PDF
Advertisement
« Page 1 of 39 »
Advertisement
Versión impresa

Muchas personas prefieren no leer el documento en la pantalla, sino en versión impresa. La opción de impresión también está prevista y puedes utilizarla haciendo clic en el enlace más arriba - Imprimir el manual. No tienes que imprimir el manual completo de 321 Studios Oil Furnace FLR110D48E, solo las páginas que elijas. Ahorra papel.

Resúmenes

A continuación encontrarás resúmenes de los contenidos incluidos en las páginas posteriores del manual de instrucciones para 321 Studios Oil Furnace FLR110D48E. Puedes utilizarlos si quieres ver rápidamente el contenido que se encuentra en la siguientes páginas del manual.

Resúmenes de contenidos
Resumen del contenido incluido en la página 1

OIL FURNACE
INSTALLATION INSTRUCTIONS
MODELS
FH085D36E FH110D48E FH110D60E
FLF085D36E FLF110D48E FLF110D60E
FLR085D36E FLR110D48E FLR110D60E
FLR140D60E FC085D36E
WARNING
READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING THE
INSTALLATION.
THIS INSTALLATION MUST COMPLY WITH THESE INSTRUCTIONS AND
THE REQUIREMENTS OF ALL GOVERNING CODES AND ORDINANCES FOR
THE INSTALLATION LOCATION.
IT IS THE RESPONSIBILITY OF INSTALLER TO KNOW AND UNDERSTAND
ALL OF THESE REQUIREMENTS.
FAILURE TO DO

Resumen del contenido incluido en la página 2

CONTENTS Getting Other Information and Publications ......... 1 Filters Upflow & Counterflow Filter Information ............. 237 Installation and Operating Instructions Lo-Boy Models – Filter Locations ....................... 28 Equipment Selection ............................................... 2 Locating the Furnace .............................................. 2 Maintenance Installing the Furnace ............................................. 6 Lubrication .................................

Resumen del contenido incluido en la página 3

GETTING OTHER INFORMATION and PUBLICATIONS These publications can help you install the furnace. You FOR MORE INFORMATION, CONTACT can usually find these at your local library or purchase THESE PUBLISHERS: them directly from the publisher. Be sure to consult current edition of each standard. ACCA Air Conditioning Contractors of America 1712 New Hampshire Ave. N.W. Washington, DC 20009 National Fuel Gas Code ........... ANSI Z223.1/NFPA54 Telephone: (202) 483-9370 Fax: (202) 234-4721 National Elec

Resumen del contenido incluido en la página 4

INSTALLATION and OPERATING INSTRUCTIONS LOCATING THE FURNACE EQUIPMENT SELECTION When installing the furnace be sure to provide adequate An accurate heating load calculation must be conducted space for easy service and maintenance. Locate the using American Society of Heating, Refrigeration and furnace as close to the chimney as practical, giving Air Conditioning Engineers (ASHRAE) or Air consideration to the accessibility of the oil burner, Conditioning Contractors of America (ACCA) manuals. c

Resumen del contenido incluido en la página 5

Manual 2100-422 Page 3 FIGURE 1 FLF/R MODELS DIMENSIONS TABLE 2 FLF/R MODELS DIMENSIONS (INCHES) FLF/FLR 085, 110 AND 140 Plenum SPECIFICATION SHEET CabinetOn peningsFs lue Conectio AirFilter 1 Model A B C D x E D x F G No. J TOP VIEW Number Width Depth Height SupplyRn eturn LocatioDH ia. J Size Used RETURN SUPPLY DUCT DUCT FLF085D36E 23 48.125 36.625 22x20 22x14 Front 6 31.625 5.125 16 x20 x1 1 FLR085D36E 23 48.125 36.625 22x20 22x14 Rear 6 31.625 5.125 16 x20 x1 1 FLF110D48E 23 48.1

Resumen del contenido incluido en la página 6

Manual 2100-422 Page 4 FIGURE 2 FH MODELS DIMENSIONS 21 7/8" TOP VIEW FH085 AND FH110 SUPPLY SPECIFICATION SHEET OPENING 19 7/8" 30 1/2" FLUE KNOCKOUT 23" FLUE KNOCKOUT FLUE KNOCKOUT OPTIONAL HIGH VOLTAGE REAR CLEANOUT ENTRANCE DOOR OPTIONAL HIGH LOW VOLTAGE VOLTAGE ENTRANCE ENTRANCE OPTIONAL OIL ENTRANCE 53" (FH085) 59" (FH110) OIL ENTRANCE LOW VOLTAGE 19 1/4" ENTRANCE FRESH AIR OPTIONAL KNOCKOUT OIL RETURN ENTRANCE RETURN OPENING OPENING 16" (CUT OUT) VESTIBULE (CUT OUT) DOOR LEFT SI

Resumen del contenido incluido en la página 7

FIGURE 3 FC085 MODEL DIMENSIONS 21 7/8" SUPPLY OPENING FC085 19 7/8" SPECIFICATION 30 1/2" SHEET TOP VIEW FLUE KNOCKOUT 23" FLUE FLUE KNOCKOUT KNOCKOUT OPTIONAL 54 1/4" REAR HIGH VOLTAGE CLEANOUT ENTRANCE DOOR OPTIONAL LOW VOLTAGE LOW VOLTAGE ENTRANCE ENTRANCE OIL ENTRANCE HIGH VOLTAGE OPTIONAL ENTRANCE OIL ENTRANCE FRESH AIR OPTIONAL FRONT VIEW KNOCKOUT OIL ENTRANCE LEFT SIDE VIEW RIGHT SIDE VIEW RETURN OPENING 18 1/8" BOTTOM VIEW MIS-1826 19 1/8" Manual 2100-422 Page 5

Resumen del contenido incluido en la página 8

DUCT WORK INSTALLING THE FURNACE The air distribution system should be designed and INSTRUMENTS REQUIRED FOR PROPER installed in conformance with manuals published by Air SETUP OF THE FURNACE Conditioning Contractors of America (ACCA) as set forth in Manual D, or ASHRAE publications. It is important that a set of instruments capable of the following requirements be used for the setup of this furnace to ensure proper and safe operation: IMPORTANT 1. Oil pump pressure gauge that measures up to Wh

Resumen del contenido incluido en la página 9

WIRING FIELD WIRING All wiring must conform to the National Electrical FACTORY WIRING Code and all local codes. A separate fuse or breaker All units are fully factory wired. Multispeed blowers should be used for the furnace. are factory wired on high speed for cooling/manual fan operation. Heating speeds are wired for the largest input and may need lower speed for field installed low input nozzle. If replacement wire is necessary, use 105 degrees C minimum. See electrical data, Table 3. TAB

Resumen del contenido incluido en la página 10

FIGURE 4 TYPICAL UNIT SETUP FLF UNIT SHOWN WARNING TYPICAL UNIT ALL WIRING MUST CONFORM TO THE SETUP NATIONAL ELECTRIC ! CODE AND ALL LOCAL (FLF UNIT SHOWN) CODES. Left side high voltage (unit power) entrance Inspection door Left side low voltage (thermostat) Right side entrance low voltage (thermostat) Left side oil entrance line entrance for opt. air boot To thermostat and optional Left side A/C unit oil line entrance To power Oil line source (see burner pump inst. for hookup info.) Shut of

Resumen del contenido incluido en la página 11

FIGURE 5 TYPICAL FLUE INSTALLATION REQUIREMENTS FRONT FLUE LOWBOY MODEL SHOWN (REPRESENTS ALL MODELS) INSTALLER NOTE: Thimble Follow all appropriate standards for installing needed venting system. Draft Regulator (Be sure to follow installation inst. supplied with 1/4 inch per regulator). 1 foot rise L 90° Rotatable Flue Box on front i flue models (remove appropriate n cabinet knockout). Mounting screws e located under flue box cover. d Flue Box C Cover h i Optional Flue m Locations n e y Oi

Resumen del contenido incluido en la página 12

OIL LINE PIPING BECKETT AFG OIL BURNER First determine whether the pipe system is to be a single This furnace is equipped with a high static Beckett AFG line system or a two line system. All connections must oil burner which is designed to produce adequate draft in be absolutely air tight or you will have a malfunction of nearly any vertically vented application. The burner the burner. When installing the piping, a good oil filter employs the latest time tested controls of the highest should

Resumen del contenido incluido en la página 13

These controls were selected for their proven high BECKETT SOLID STATE IGNITER quality, dependability, and serviceability. With proper This igniter differs from the traditional iron core maintenance this burner assembly will provide many transformer in that it produces a 14,000 volt spark years of reliable service. instead of a 10,000 volt spark of the iron core transformer. This hotter spark provides for cleaner, All units are shipped with the oil burner installed, and faster ignitions. Bein

Resumen del contenido incluido en la página 14

BECKETT R7184B PRIMARY OPERATIONAL GUIDE Pre-Purge Delay – 15 seconds on delay LED Codes – Flashing 1/2 second on / 1/2 second off – system is locked out or in restricted mode (hard lockout). – Flashing 2 seconds on / 2 seconds off – control is in recycle mode (soft lockout). – ON – CAD cell is sensing flame – OFF – CAD cell is not sensing flame. Ignition Trials – On any given call for heat the fail then the control goes into a hard lockout or control will allow three ignition trials

Resumen del contenido incluido en la página 15

FIGURE 7 ELECTRONIC BLOWER CONTROL TRANSFORMER 24V THERMOSTAT SECONDARY CONNECTIONS CONNECTIONS 3 AMP FUSE HEATING BLOWER OFF DELAY ADJUSTMENT IN SECONDS. OIL PRIMARY T-T CONNECTIONS LINE VOLTAGE CONNECTION (HOT) HUMIDIFIER CONNECTION UNUSED BLOWER MOTOR SPEED CONNECTIONS HEATING BLOWER LINE VOLTAGE SPEED CONNECTION CONNECTION (COM, L2) MIS-1819 ELECTRIC AIR COOLING BLOWER CLEANER CONNECTION SPEED CONNECTION Manual 2100-422 Page 13

Resumen del contenido incluido en la página 16

TABLE 4 FURNACE DATA Fn urnace Installed Standard Field Installed Optio s 2 2 2 1 Heating 1 Heating 1 Heating Nozzle Input Capacity Nozzle Input Capacity Nozzle Input Capacity ModelNumber Size BTUH BTUH Size BTUH BTUH Size BTUH BTUH F5 LF085D36E.0 710 05,0085 5,00.0 690 1,0075 4,00.0 570 7,00 63,00 F5 LR085D36E.0 710 05,0085 5,00.0 690 1,0075 4,00.0 570 7,00 63,00 F0 LF110D48E10 .010 40,0015 13,00.0 810 19,009A 6,00 NANA N F0 LR110D48E10 .010 40,0015 13,00.0 810 19,009A 6,00 NANA N F0 LF110D60

Resumen del contenido incluido en la página 17

K. Adjust Air Setting Examine the smoke - CO It should be located as close as possible to the 2 plot and, keeping in mind the curve of oil burner. Care should be taken to prevent air Figure 6, note the location of the “knee” where leakage in the oil suction line. Use continuous the smoke number begins to rise sharply. runs of copper tubing and use minimum Noting the air gate position marks, adjust the number of joints and fittings. Always use flare air setting to a CO level 1/2 to 1 percent

Resumen del contenido incluido en la página 18

4. FINAL CHECKS SHORT FORM ADJUSTMENT PROCEDURE M. Measure Stack Temperature Operating the unit at an excessive firing rate will generate Some burner service organizations may wish to more heat than the heat exchanger can utilize perform a shorter procedure for the adjustment of oil and result in unnecessary heat loss up the burners. The following is an example of such a short chimney. Other causes of excessive heat loss form prepared by the National Association of Oil Heat are badly sooted

Resumen del contenido incluido en la página 19

FIGURE 8 TYPICAL SMOKE – CO CHART WITH ADJUSTMENT RANGE 2 High Air Settings Low 8 CO Curve 2 from plotted 6 points Plotted point Normal adjustment 4 range Tolerance to "knee" "Best" air Plotted point setting 2 Plotted point "Knee" 0 6 8 10 12 14 Percent CO in Flue Gas 2 Technician's plotting area 8 6 4 2 0 6 810 12 14 MIS-1827 Percent CO in Flue Gas 2 Manual 2100-422 Page 17 Bacharach Smoke Number Bacharach Smoke Number

Resumen del contenido incluido en la página 20

FIGURE 9 PRESSURE GAUGE CONNECTION TO BLEED PORT Remove Bleed Port to attach pressure guage. Pressure Gauge MIS-1660 Manual 2100-422 Page 18


Manuales de instrucciones similares
# Manual de instrucciones Categoría Descargar
1 321 Studios EPSON Endeavor 4DX/33 Manual de instrucciones Máquina de café 2
2 321 Studios Oil Furnace FLF110D48E Manual de instrucciones Máquina de café 1
3 321 Studios Oil Furnace FLR085D36E Manual de instrucciones Máquina de café 0
4 321 Studios Digital to Analogue Converter D33 Manual de instrucciones Máquina de café 2
5 321 Studios JBL Control 29AV Manual de instrucciones Máquina de café 6
6 321 Studios Dell Dimension Computer 8400 Series Manual de instrucciones Máquina de café 15
7 321 Studios Oil Furnace FC085D36E Manual de instrucciones Máquina de café 4
8 321 Studios Oil Furnace FLR140D60E Manual de instrucciones Máquina de café 1
9 321 Studios Xerox Color Laser Printer 6300/6350 Manual de instrucciones Máquina de café 0
10 321 Studios Meridian Internet Telephony Gateway (ITG) Trunk 2.0 Manual de instrucciones Máquina de café 6
11 321 Studios EPSON Endeavor 486C Manual de instrucciones Máquina de café 1
12 321 Studios Oil Furnace FH110D60E Manual de instrucciones Máquina de café 1
13 321 Studios Oil Furnace FLR110D60E Manual de instrucciones Máquina de café 1
14 321 Studios Oil Furnace FLF110D60E Manual de instrucciones Máquina de café 1
15 321 Studios INDUCTION HOBS 7322 230 Manual de instrucciones Máquina de café 1
16 Philips coffee maker flavor select HD7606 Manual de instrucciones Máquina de café 3
17 Sony WALKMAN D-EJ2000 Manual de instrucciones Máquina de café 19
18 Philips HD 7820/65 Manual de instrucciones Máquina de café 62
19 Philips coffee maker flavor select HD7612 Manual de instrucciones Máquina de café 91
20 Philips HD7544 Manual de instrucciones Máquina de café 8