Resumen del contenido incluido en la página 1
CONTENTS
INSTRUCTIONS FOR USE
LIMITED ENGINE WARRANTY ..........................................................3
MODEL EH64
SAFETY PRECAUTIONS....................................................................6
WELDER APPLICATION
INTRODUCTION.................................................................................9
DESCRIPTION..................................................................................11
SPECIFICATIONS...........................................
Resumen del contenido incluido en la página 2
3 Year Limited Engine Warranty 6. Engine tune-ups and normal maintenance service including, but not limited to, valve adjust ment, normal replacement of service items, fuel and lubricating oil, etc. (Special Term for Welder Application) 7. Any engine which has been subject to negligence, misuse, accident, mis- (Effective with engines purchased from Robin America, Wood Dale, IL, after November 15, application or over-speeding. 1993) 8. Any engine that has been installed, repaired, or alter
Resumen del contenido incluido en la página 3
Safety Precautions WARNING : Before operating the engine, read this manual and become The engine exhaust from this product contains familiar with it and the equipment. Safe and effi cient operation chemicals known to the State of California to cause cancer, birth defects or other reproductive can be achieved only if the equipment is properly operated and harm. maintained. The following symbols, found throughout this manual, alert you to potentially dangerous conditions to the operator, servic
Resumen del contenido incluido en la página 4
moving parts, etc. • Used engine oils have been identifi ed by some state and EXHAUST SYSTEM federal agencies as causing cancer or reproductive toxicity. When • Exhaust products of any internal combustion engine are toxic and checking or changing engine oil, take care not to ingest, breathe can cause injury, or death it inhaled. When operating the engine in a the fumes, or contact used oil. confi ned area, make sure the ventilation system is operating • Do not work o
Resumen del contenido incluido en la página 5
Introduction ABOUT THIS MANUAL This manual covers the operation and maintenance of the horizontal- shaft Robin Subaru EH64 engines for welder applications (OHV220 Performer Series). Each operator of the power equipment should study this engine manual carefully and observe all of its instructions and precautions. Proper use and periodic maintenance are responsibilities of the operator(s) and are essential for top performance. MODEL IDENTIFICATION Whenever contacting a dealer or distributor fo
Resumen del contenido incluido en la página 6
Description Specifi cations FEATURES Air-Cooled, 4-Stroke, V-Twin Cylinder, Horizontal Shaft, • Overhead valve arrangement enables high power, and low fuel and Engine Type OHV Gasoline Engine oil consumption Rated Output 20.5 HP/3600 rpm (153. kW/3600) • V-Twin, four stroke design Continuous Output 16.0 HP/3600 rpm (11.9kW/3600) • Air-cooled and gasoline fueled • The light weight and compact design makes it easy to install and Bore X Stroke 80 mm x 65 mm (3.15” x 2.56”) utilize for many ap
Resumen del contenido incluido en la página 7
Installation carburetor. LOCATING If the tank is mounted above the carburetor, a fuel shut-off valve must Locate the engine at least 1 meter (3.0 ft) away from buildings or other be connected between the fuel tank and the fuel pump. structures. Provide proper exhaust routing. Refer to EXHAUST SYS- Note: To prevent fuel from fl ooding the carburetor, the fuel valve TEM below. Do not use the engine near fl ammables or other hazard- must be closed when the engine is not running. ous materials such
Resumen del contenido incluido en la página 8
Installation Check the oil level daily, before starting. Keep the oil level between the ENGINE OIL upper and lower level on the gauge. Recommendations Use premium quality motor oil, Class SE or higher. Look for the SAE (Society of Automotive Engineers) or API viscosity grade. Referring to the table below, choose the viscosity grade appropriate for the ambient temperatures expected during the period of time until the next sched- uled oil change. EXPECTED AMBIENT SAE VISCOSITY TEMPERATURES GR
Resumen del contenido incluido en la página 9
Installation WIRING BATTERY CABLES The engine is equipped with a wiring harness that connects with the accessory. 1. Connect the positive (+) battery cable between the starter solenoid and the battery. 2. Connect the ground strap between the negative (-) battery terminal and a clean, bare metal grounding location on the engine. 3. Connect wires from starter key switch to starter solenoid and ground. WIRE GAUGE CABLE AWG (BS) CABLE DIA. SAE JIS LENGTH BWG Less than 1.5 m 1.5mm 14 16
Resumen del contenido incluido en la página 10
Wiring Diagram POWER TRANSMISSION Belt Drive If using a belt drive application, consider the following notes: • V-belts are preferable to fl at belts • The engine drive shaft must be parallel to the machine drive shaft • The engine drive pulley must be in line with the machine drive pulley • Install the engine pulley as close to the engine as possible • Span the drive belt horizontally, if possible. • Disengage the load when starting the engine. ENGINE WIRING DIAGRAM (6 PIN) Engi
Resumen del contenido incluido en la página 11
Operation any indications of fuel leakage. Do not operate engine until all leaks are repaired. ! WARNING EXHAUST GAS IS DEADLY! 4. Check and tighten any loose bolts or nuts. Exhaust gases contain carbon monoxide, an odorless and color- less gas. Carbon monoxide is poisonous and can cause uncon- 5. Check the oil and refi ll, if necessary. Do not overfi ll. sciousness and death. Symptoms of carbon monoxide poisoning include: Starting the engine without oil will cause severe ! CAUTION • D
Resumen del contenido incluido en la página 12
3. After the engine starts, slowly push the choke to the full- OPERATING IN DUSTY CONDITIONS open position. Pull it back, if necessary, to keep the engine 1. Keep the engine cooling fi ns and fl ywheel air inlet screen clean. running smoothly until the engine is at operating temperature 2. Perform air cleaner maintenance more often than normal-as In colder weather, the engine will take longer to begin required. running smoothly with the choke open. 3. Change the engine oil and oil fi lte
Resumen del contenido incluido en la página 13
6 Perform air cleaner maintenance as instructed in Periodic Maintenance. ! WARNING EXHAUST GAS IS DEADLY! Never operate engine-powered equipment 7 Plug the exhaust outlet to prevent moisture, dirt, bugs, ect. from indoors without a proper exhaust system, ample fresh entering. air ventilation and an operable carbon monoxide detector. ! WARNING Battery gas is explosive. Wear safety glasses 2. Use fresh gasoline and fi ll the fuel tank after each day’s use to and do not smo
Resumen del contenido incluido en la página 14
Periodic Maintenance Periodic Maintenance MAINTENANCE, REPLACEMENT, OR REPAIR OF THE EMISSION Keep a log of maintenance performed and the run time hours. Keeping CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY a record of procedures will help you keep scheduled maintenance and NON-ROAD ENGINE REPAIR ESTABLISHMENTS OR provide a basis for supporting warranty claims INDIVIDUALS. Periodic maintenance is essential for top engine performance. See the Maintenance, replacement or repair of emiss
Resumen del contenido incluido en la página 15
! WARNING Crankcase pressure can blow hot engine oil out the fi ll tube causing severe burns. Always stop the engine before removing the oil fi ll cap. If the engine is equipped with the long oil fi ll tube, turn the oil fi ll cap counterclockwise and lift it up. Wipe the dip stick clean, push it back into the oil fi ll tube until the cap seats. Withdraw it again to check the oil level. CHANGING OIL AND FILTER Change the oil and fi lter after the fi rst 20 hours of operation. Thereaf- ter, ch
Resumen del contenido incluido en la página 16
10 DO NOT FILL TO A LEVEL ABOVE THE FULL MARK ON THE Foam Filter DIPSTICK. Drain the excess oil if too much has been added. Remove and wash the urethane foam in water and detergent. Squeeze the foam wrapper dry like a sponge. Rinse with clean water and allow it to dry. Coat the wrapper evenly with 14 mL (one tbsp.) of SAE 30 engine oil. Knead the oil into the wrapper and squeeze out the excess oil. Note: Failure to adequately wring out excess oil from the wrapper may cause a drop in engi
Resumen del contenido incluido en la página 17
SPARK PLUG MAINTENANCE AND REPLACEMENT To adjust the speed control solenoid: 1 Run the engine with no load until the engine control times out Refer to the Specifi cations for spark plug type and gap specifi cations. Check and clean spark plugs every 200 hours. Replace plugs every (about 15 seconds) and energizes the solenoid. 500 hours. 2 Adjust engine to 2200 RPM by loosening the two slotted screws To prevent cross threading the spark plug, always thread it in by hand retaining the solen
Resumen del contenido incluido en la página 18
Speed Control Adjustments Engine Starting Damaged spark plug(s). Check the spark plug gap. Check for Engine cranks but a bad insulator on plug and replace if damaged. Clean carbon fails to start deposit from electrode. Id wet, dry electrode. Engine speed adjustment must be attempted only by a qualifi ed me- chanic and the adjustments must be made using an accurate tachom- Fuel Supply. Check fuel supply and shut-off valve. Check fuel fi lter eter. It is recommended that low-idle speed be adjuste
Resumen del contenido incluido en la página 19
IMPORTANT INFORMATION FOR CALIFORNIA ENGINE USERS Engine Overheats Air fl ow is obstructed at inlet or cylinder baffl e. Clean out debris in baffl e. These engines meet the requirements of California’s Exhaust Emis- sions Standards for 1995 and later for Utility and Lawn and Garden Improper engine oil. Replace oil. Equipment Engines. As a California user of these engines, please be aware that unauthor- Lean air/fuel mixture. Check for plugged passages in carburetor. ized modifi cations or replacem
Resumen del contenido incluido en la página 20
FEDERAL EMISSIONS COMPONENT DEFECT WARRANTY *The replacement parts used for required maintenance services. EMISSIONS COMPONENT DEFECT WARRANTY COVERAGE - This emission warranty is applic- able in all States, except the State of California *Consequential damages such as loss of time, inconvenience, loss of use of the engine or equip- ment, etc. *Diagnosis and inspection charges that do not result in warranty-eligible service being performed. Fuji Heavy Industries Ltd. and Robin America Inc., Wood
