Resumen del contenido incluido en la página 1
f.I
/
~
~
MAN CO..
P. O. BOX 36940
--
I
CLEVELAND, OHIO 44136
1410 West Ganson Street -Jackson, Michigan 49202
0611-7588
PRINTED !N U.S.A.
" ~'r IYARD. and
Resumen del contenido incluido en la página 2
Your SNOW THROWER is a precision piece of snow throwing equipment. Engineering skill and experience have been combined to provide the ultimate in safety and efficiency. As with any type of power equipment, carelessness or error on the part of the operator can result in injury. EXERCISE EXTREME CAUTION AT ALL TIMES. 1.. READ THE OWNER'S MANUAL CAREFULLY. Know the controls to operate your SNOW THROWER properly and how to quickly stop th~unit. BEFORE STARTING ENGINE, disengage all clutches and shif
Resumen del contenido incluido en la página 3
CE~ FREE OPERATION , GENERAL SNOW~THROWING 1.~ Always keep area to be cleaned cleared before~owfall~. . 2.~. Always start engine with machine on level surface with master clutch disengaged: After starting, let engine warm up several ';;;.. ""i" '-. minutes at slow speed before starting to remove ~now~ Ifinachine is stored indoors, let engine and machine adjust to outdoor temperatures before starting to throw snow': ... ..'co 3. When throwing snow, ~u!:, machln.eat.~ull throttl~ for best re~lts:
Resumen del contenido incluido en la página 4
AND SET-UP 1. Before assembling your Snow Thrower be sure all hardware, parts, and instructions have been removed from the carton. , ...:' ':;.' '-2. Assemble right and left handle tubes to the unit with bolts, lockwashers, and flat washers. Do not tighten.3. Assemble handle panel assembly to the under side of right and left handle tubes and secure with four slotted hex head bolts and lock nuts. Tighten all bolts on the handle assembly.4. Assemble chute adjustment shaft through hole in the ha
Resumen del contenido incluido en la página 5
BEFORE STARTING ENGINE 1. Fill the fuel tank with fresh winter blend regular gaso- line. DO NOT MIX OIL WITH GASOLINE. Make certain the fuel shut-off valve under the gas tank is turned on. 2. Place machine on a level surface. Remove oil fill cap and fill crankcase with good quality detergent oil. Use MS classification SAE 5W-20 oil for operation below 400 F. Use MS classific:atio~ SAE 30 oil for operation above 400 F . 3. During initial "Break-in" period, the oil should be checked often. . 4. Ch
Resumen del contenido incluido en la página 6
OPERATION OF CONTROLS CONTROL MASTERCLUrCH The master clutch control is located on handle panel and IS used to engage, all power~Select:8 forward speed or rever~ " ' ",,'c,';""...c"":, with shift lever, then release master clutch control and push , '.. c, ,," ,. - f,orward to engage ?rive diS?: f~~: reel. To disengage, pu II master clutch control back and lock in notch. The master ." " , ,,'.. ' clutch control must always'beln: neutral position before -, '~-""'" ,.' -' -' ":!, , . starting engin
Resumen del contenido incluido en la página 7
. REPLACING SAFETY SHEAR BOLT If the intake snow reel should jam causing the safety shear bolt to shear, it may be replaced with a new bolt, furnished in the parts bag, after removing the broken pieces in the shaft. NOTE: Always align the hole in the reel shaft and the sprocket shaft before driving out the broken bolt. Do NOT remove solid pin located near shear bolt hole. CHUTE CHAIN AND-ADJUSTMENT To tight~n the chute chain, rotate the chute all the way to the left, until the adjustment bolt is
Resumen del contenido incluido en la página 8
Resumen del contenido incluido en la página 9
Resumen del contenido incluido en la página 10
PARTS LIST MODEL 7200-0 Your SNOW THROWER is right hand (R.H.I or left hand (L.H.I as you operate machine. 105 3622-122 -Cover-Chain (Inside) ..'. 1539-80 Nut -Push 1/2 i \."..- 1 106 3765-6 Strap -Scoop Mount R.H. ,. 2 1658-29-40 Roller -Crenk :; '\' 41256 Wa,her-S.A,E, 1/2 ',' , 107 2168-55 Assembly -Freme :I 2119-4b A...mb!y-ChIJteCrank'" " 108 1654-35 Chain -Reel W/Conn. Link ~ 40 x 110 Pitch. 4 109 SeePage 11 6 3616-006 Decal- Handle Panel 110 c SeePage 11 , " 6 1538-30 Nut -Hex Lock 1/4-20
Resumen del contenido incluido en la página 11
P ARTS LIST REF. PART REF. PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION t 1654-31 Chain -W/Connactlng Link 22 42180 Nut -Hex Lock No. 10-24 Esne No.41 x 28 pitches 23 3606-146 Plate -Pivot R.H. 2 1624-192 Spacer-Gear Sprocket 24 1652-108 Bearing -Ball Saaled -3 1652-114 Baaring-Needla7/16x 1/2 L. 25 1629-14 Flange -Retainer 4 1149-5 A-mbly -Gaar & Sprocket W/Bearlng 26~,c 1511-39 Screw -Slotted Truss Head (Included Ref. No.3) No. 10-24 x 518 .6 42342 Nut -Hex Lock 3/8.16 (Eslok) 27 1540-99 Wash
Resumen del contenido incluido en la página 12
NOTE: Make all adjustments with the engine turned off ..., and wire removed from th~- sparkplug. (Fasten wire to II .., cylinder head at least 1 away.from sparkplug.) IDLER LINKAGE ADJUSTMENT .:.~. :a~.!...L:. ~ Should the drive belt stretch enough to prevent the ad justment link from moving freely in the idler arm, slot, with the master clutch lever in drive position, adjust' as follows. With master clutch in drive position, remove cotter pin .~ from adjustment link. Thread the link up the rod
Resumen del contenido incluido en la página 13
LUBRICA TION- CHANGING ENGINE OIL Drain oil when engine is warm. To drain oil, place pan under frame directly beneath oil drain extension. Remove oil drain cap and allow oil to drain completely. Replace drain cap and tighten securely. Refill to "Full", approxi- mately 1 pint. See engine manual for complete engine lub. rication and service instructions. LUBRICATION POINTS lUBRICATE THE PARTS PERIODICAllY AS IllUS-TRATED. The following points are to be lubricated every five hours of operation wit
Resumen del contenido incluido en la página 14
cable roller bracket and down to the right hole in the CHUTE CABLE REPLACEMENT top of the blower housing. C. Turn the cable pulley with the cable bolt toward the OR REPAIR bottom of the blower housing. , , " .'\ ' . D. Put the ends of the cable up through the holes in the bottom of the cable pulley and cross the ends up and 1. REMOVE THE BLOWER HOUSIN~ FROM THE over the cable bolt and under the washer. Pull the MACHINE. cable tight and tighten the' ~ble bolt and nut, making A. Remove the ~ain gu
Resumen del contenido incluido en la página 15
.~';:;j 15 1~
Resumen del contenido incluido en la página 16
30" SNOW THROWERyou enjoy these outstanding features ~ 7/73
