Resumen del contenido incluido en la página 1
EP-3V EP-3V EP-3VCA2 CA2 CA2
EP-3V EP-3VCA2 CA2
A Soc A Sock ket 370 Pr et 370 Processor based 4X ocessor based 4X A AGP GP
A Soc A Soc A Sock k ket 370 Pr et 370 Pr et 370 Processor based 4X ocessor based 4X ocessor based 4X A A AGP GP GP
mainboard (133/100/66MHz) mainboard (133/100/66MHz)
mainboard (133/100/66MHz) mainboard (133/100/66MHz) mainboard (133/100/66MHz)
Suppor Supports PC-133 SDRAM Module ts PC-133 SDRAM Module
Suppor Suppor Supports PC-133 SDRAM Module ts PC-133 SDRAM Module ts PC
Resumen del contenido incluido en la página 2
EP-3VCA2 User Notice No part of this product, including the product and software may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form without the express written permission of EPoX Computer Company (hereinafter referred to as EPoX) except for documentation kept by the purchaser for backup purposes. We provide this manual as is without warranty of any kind, either expressed or implied, including but not limited to the implied war
Resumen del contenido incluido en la página 3
EP-3VCA2 Technical Support Services If you need additional information, help during installation or normal use of this product, please contact your retailer. Your retailer will have the most current information about your configuration. If your retailer cannot help, you may visit our online technical support website and/or contact our support technicians at the locations listed below. Record your serial number before installing your EP-3VCA2 mainboard. (The serial number is located near the I
Resumen del contenido incluido en la página 4
EP-3VCA2 Table of Contents Page Section 1 Introduction Components Checklist ........................................ 1-1 Overview EP-3VCA2 Form-Factor ..................................... 1-2 I/O Shield Connector .......................................... 1-3 Power-On/Off (Remote) ..................................... 1-3 System Block Diagram........................................ 1-4 Section 2 Features EP-3VCA2 Features ............................................ 2-1 Section 3 Installation E
Resumen del contenido incluido en la página 5
EP-3VCA2 Save & Exit Setup ................................................ 4-25 Exit Without Saving ............................................. 4-25 Appendix Appendix A Memory Map ....................................................... A-1 I/O Map ................................................................ A-1 Timer & DMA Channels Map ............................. A-2 Interrupt Map ....................................................... A-2 RTC & CMOS RAM Map ............................
Resumen del contenido incluido en la página 6
EP-3VCA2 Page Left Blank
Resumen del contenido incluido en la página 7
EP-3VCA2 Introduction Section 1 INTRODUCTION Components Checklist ü ü ü ü ü A. (1) EP-3VCA2 mainboard ü ü ü ü ü B. (1) EP-3VCA2 users manual ü ü ü ü ü C. (1) Floppy ribbon cable ü ü ü ü ü D. (1) ATA-66 Hard drive ribbon cable E. (1) PS/2 to AT keyboard connector adapter (Optional) F. (1) USB Cable (Optional) ü ü ü ü ü G. (1) Driver and utility USERS C MANUAL EP-3VCA2 D B A E or F G Page 1-1
Resumen del contenido incluido en la página 8
Introduction EP-3VCA2 EP-3VCA2 Form-Factor The EP-3VCA2 is designed with ATX form factor - the new industry standard of chassis. ATX form factor is essentially a Baby-AT baseboard rotated 90 degrees within the chassis enclosure and a new mounting configuration for the power supply. With these changes the processor is relocated away from the expansion slots, allowing them all to hold full length add-in cards. ATX defines a double height aperture to the rear of the chassis which can be used to ho
Resumen del contenido incluido en la página 9
EP-3VCA2 Introduction I/O Shield Connector The EP-3VCA2 is equipped with an I/O back panel. Please use the appropriate I/ O shield (figure 3). Joystick/Midi parallel port PS/2 Mouse USB port PS/2 KEYBOARD COM1 COM2 Speaker Line_in MIC Figure 3: I/O back panel layout Power-On/Off (Remote) The EP-3VCA2 has a single 20-pin connector for ATX power supplies. For ATX power supplies that support the Remote On/Off feature, this should be connected to the systems front panel for system Power On/Off butt
Resumen del contenido incluido en la página 10
Introduction EP-3VCA2 System Block Diagram Socket 370 Processor 133/100/66MHz PAC 133/100/66MHz 66MHz PCI Bridge AGP Bus and memory 4X controller VT82C694X AGP Slot AMR Slot AC 97 VT82C686A I/O Bridge USB 0,1 USB 2,3 Figure 5: System Block Diagram Page 1-4
Resumen del contenido incluido en la página 11
EP-3VCA2 Features Section 2 FEATURES EP-3VCA2 Features: EP-3VCA2 is based on the Socket 370 Processors including PPGA & FC- PGA operating at 300 ~ 800MHz. Designed with VIA Apollo Pro 133A PCIset. Supports up to 768MB of DRAM (minimum of 8 MB) on board (please see Section 3-2). EP-3VCA2 will support Error Checking and Correcting (ECC) when using parity SDRAM memory modules. This will detect multiple bit errors and correct 1-bit memory errors. Supports (5) 32 bit PCI slots, (1) 4X AGP s
Resumen del contenido incluido en la página 12
Features EP-3VCA2 4 USB ports are provided, 2 ports are onboard and another 2 USB ports, as option, need USB an cable on USB2 position. The onboard VT82C686A chip provides the means for connecting PC peripherals such as; keyboards, joysticks, telephones, and modems. Built-in ATX 20-pin power supply connector. ® Software power-down when using Windows 95/98. Supports ring-in feature (remote power-on through external modem, allows system to be turned on remotely). Resume by Alarm - Allows
Resumen del contenido incluido en la página 13
EP-3VCA2 Installation Section 3 INSTALLATION Page 3-1
Resumen del contenido incluido en la página 14
Installation EP-3VCA2 EP-3VCA2 Detailed Layout Figure 1 Page 3-2
Resumen del contenido incluido en la página 15
EP-3VCA2 Installation Easy Installation Procedure The following must be completed before powering on your new system: 3-1. CPU Insertion 3-2. Jumper Settings 3-3. System memory Configuration 3-4. Device Connectors 3-5 External Modem Ring-in Power ON and Keyboard Power ON Functions (KBPO) 3-6. STR Function Section 3-1 CPU Insertion TM CPU Insertion: (use CuMine for reference) Step 1 Open the socket by raising the actuation lever. Figure 2 Step 2 Insert the processor. Ensure proper pin 1 orientati
Resumen del contenido incluido en la página 16
Installation EP-3VCA2 Step 3 Close the socket by lowering and locking the actuation lever. Figure 4 Note: Intels reference design thermal solution is an active heatsink; an extruded alumi- num heatsink based and a fan attached to the top on the fin array. (See Figure 5) Figure 5 Page 3-4
Resumen del contenido incluido en la página 17
EP-3VCA2 Installation Section 3-2 Jumper Settings The EP-3VCA2 motherboard was designed with very few jumpers to make your installation faster and easier. SW2: CPU Vcore Voltage Selection SW2 CPU Vcore 56 12 3 4 AUTO ON NONON O 1.6V ON ON N ONONON O 1.65V ON N ON O 1.7V 5 12 34 6 ON N ONON O 1.75V ON N ONON O 1.8V ON NONONON O 1.85V ON N ONONON O 2.0V ON N ONONONON O 2.05V ON N O 2.1V ON N O 2.2V JP1 CMOS Clear JP1 = 1-2 Normal (Default) 1 = 2-3 Clear CMOS JP2: VIO (3.3V) Adjust Selection Jt
Resumen del contenido incluido en la página 18
Installation EP-3VCA2 JP4 Keyboard Power-ON Function 1 JP4 = 1-2 Disabled (Default) = 2-3 Enabled JP5 Power Loss Recovery JP5 = 1-2 Disabled 1 = 2-3 Enabled JP6 STR Function JP6 = 1-2 Disabled 1 = 2-3 Enabled Page 3-6
Resumen del contenido incluido en la página 19
EP-3VCA2 Installation Section 3-3 System Memory Configuration Memory Layout The EP-3VCA2 supports (3) PC133 168-pin DIMMs (Dual In-line Memory Module). The DIMMs is for SDRAM (Synchronized DRAM). DIMM SDRAM may be 83MHz (12ns), 100MHz (10ns) or 125MHz (8ns) bus speed. If you use both 50ns and 60ns memory you must configure your BIOS to read 60ns. When using Synchronous DRAM we recommend using the 4 clock variety over the 2 clock. Figure 6 and Table 1 show several possible memory configura
Resumen del contenido incluido en la página 20
Installation EP-3VCA2 DIMM Module Installation Figure 7 displays the notch marks and what they should look like on your DIMM memory module. DIMMs have 168-pins and two notches that will match with the onboard DIMM socket. DIMM modules are installed by placing the chip firmly into the socket at a 90 degree angle and pressing straight down (figure 8) until it fits tightly into the DIMM socket (figure 9). LEFT KEY ZONE CENTER KEY ZONE (UNBUFFERED) (3.3 V DRAM) Figure 7 Figure 8 DIMM Module clip be
