Resumen del contenido incluido en la página 1
SyncMaster 403T
Resumen del contenido incluido en la página 2
INDEX
Resumen del contenido incluido en la página 3
Resumen del contenido incluido en la página 4
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock
Resumen del contenido incluido en la página 5
Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. Do not excessively bend the plug and wire nor pl
Resumen del contenido incluido en la página 6
Installation Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Put your monitor in a location with low humidity and a minimum of dust. An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. This may cause damage to the product or human body. Place the monitor on a flat and stable surface. The monitor can cause injury by falling. Set down the monitor carefully. It could be damaged or broken.
Resumen del contenido incluido en la página 7
Cleaning When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric. Do not spray detergent directly on the monitor. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector can cause an electric shock or fire. Do not set a glass of water, chemicals or any small metal objects on the monitor. This may cause damage, electri
Resumen del contenido incluido en la página 8
Other Do not remove cover(or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel. If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or fire. Do not place any heavy objects on the monitor. This may cause an electric shock or a fire. Fo
Resumen del contenido incluido en la página 9
Unpacking Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Signal Cable Power Cord Cover-hole (15 pin D-Sub) Remote Control / Monitor RS232C CABLE Batteries (AAA X 2) Warranty Card User's Guide CD (Not available in all locations) Temporary Stand Sold separately Wall Mount KIT Speaker Set Stand Kit PIVOT Installation CD Contact a local Samsung Electronics service center to buy optional items.
Resumen del contenido incluido en la página 10
Front For detailed information concerning the monitor functions, refer to User Controls under Adjusting Your Monitor. The monitor's front configuration may vary slightly depending on the monitor model. 1. Auto button 6. Menu button 2. Source button 7. Power button 3. Exit button 8. Power indicator 4. Navigate button (Up-Down Button) 9. Remote Control Sensor 5. Adjust button (Left-Right Button) / Volume button
Resumen del contenido incluido en la página 11
Rear For detailed information concerning cable connections, refer to Connecting Cables under Setup. The monitor's rear configuration may vary slightly depending on the monitor model. 1. Power On/Off Switch 2. Power port 3. EXTERNAL CONTROL (RS232C Serial PORT) : MDC(Multiple Device Control) Program Port 4. PC Video Connection Terminal : Using D-Sub Cable (15 pin D-Sub) - RGB 1 mode (Analog PC) 5. PC Video Connection Terminal : Using DVI Cable (DVI-D to DVI-D) - RGB 2 mode (Digital PC
Resumen del contenido incluido en la página 12
Rear 6. PC Video Connection Terminal / Component Connection Terminal : BNC cable (Input) - RGB 3 (Analog PC) Connection : connecting B, G, R, H, V port - Component Connection : connecting Pb, Y, Pr port 7. PC Video Loopout Connection Terminal (RGB 3 (Analog PC)) / Component Loopout Connection Terminal (Component) - BNC cable(Output) 8. CVBS Video Connection Terminal : Video 1 mode (Input) 9. CVBS Video Loopout Connection Terminal (Output) 10. S-Video Connection Terminal : Video 2 mode
Resumen del contenido incluido en la página 13
Remote Control For detailed information of the Remote Control Unit functions, refer to Adjusting Your Monitor > User Controls > User Control Buttons > Remote Control buttons. The remote control's configuration may vary slightly depending on the monitor model. The Remote control may function within a range of 0.23 to 33 feet (7cm to 10m) and 30 degrees to the left and right of the monitor's Remote Control Reception sensor. Button Names | Replacing Batteries | Usage 1. Button Names 1.
Resumen del contenido incluido en la página 14
Mechanical Lay-out 1. Mechanical Lay-out 2. Monitor Head
Resumen del contenido incluido en la página 15
Mechanical Lay-out 3. Stand 4. Speaker
Resumen del contenido incluido en la página 16
Mechanical Lay-out 5. Mounting Bracket
Resumen del contenido incluido en la página 17
Installing Stand Kit Only the supplied bolts should be used. Samsung Electronics will not be responsible for damages caused by using a base other than those specified. 1. Installing the Temporary Stand Left stand Right stand 1. A cover-protector is used to protect the hole at the bottom of the monitor, where the stand is inserted. Be sure to remove the cover-protector when attaching the provided temporary stand or stand kit (sold separately) and cover the hole using the cover-hole when
Resumen del contenido incluido en la página 18
Installing Stand Kit 2. Installing Stand Kit (sold separately) 1. A cover-protector is used to protect the hole at the bottom of the monitor, where the stand is inserted. Be sure to remove the cover-protector when attaching the provided temporary stand or stand kit (sold separately) and cover the hole using the cover-hole when attaching the wall mount kit. 2. Make sure you put the parts in the right direction and in the right place. (M5 × 4) 3. Put the stand into the hole at the
Resumen del contenido incluido en la página 19
Connecting Your Monitor AV input devices like DVDs, VCRs or Camcorders as well as your computer may be connected to the monitor. For detailed information on connecting AV input devices, refer to User Controls under Adjusting Your Monitor. Connecting to a Computer | Connecting to a VCR | Connecting to a DVD Player | Connecting a Camcorder Connecting D-TV Set Top Box | Connecting Speaker | Connecting to an Audio System 1. Connecting to a Computer 1. Connect the power cord for you
Resumen del contenido incluido en la página 20
Connecting Your Monitor 2. Connecting to a VCR 1. AV input devices like VCRs or Camcorders are connected to the S-Video Connection Terminal or CVBS Video Connection Terminal of the monitor using the S-VHS or BNC cable. S-VHS or BNC cable is optional. 2. Connect the Audio (L) and Audio (R) terminals of a VCR or Camcorders to the monitor's CVBS, S- Video Audio Connection Terminal using audio cables. 3. Select Video 1 or Video 2 that is connected to a VCR or Camcorders using
