Resumen del contenido incluido en la página 1
SyncMaster 731N
Install drivers Install programs
Resumen del contenido incluido en la página 2
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for an extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode.
Resumen del contenido incluido en la página 3
Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. A bad connection may cause fire. Do not excessively bend the plug and wire nor place
Resumen del contenido incluido en la página 4
Be sure to contact an authorized Service Center, when installing your monitor in a location with the heavy dust, high or low temperatures, high humidity, chemical substance and where it operates for 24 hours such as the airport, the train station or etc. Failure to do so may cause a serious damage to your monitor. Put your monitor in a location with low humidity and a minimum of dust. Failure to do so may cause an electric shock or fire inside the monitor. Do not drop th
Resumen del contenido incluido en la página 5
Set down the monitor carefully. The monitor could be damaged or broken. Do not place the monitor face down. The TFT-LCD surface may be damaged. Installing a wall bracket must be done by a qualified professional. Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10 cm/4 inches ) for ventilation purposes. Poor ve
Resumen del contenido incluido en la página 6
Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector may cause an electric shock or fire. Make sure to unplug the power cord before cleaning the product. Otherwise, this may cause electric shock or fire. Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol, thinn
Resumen del contenido incluido en la página 7
could be exposed to snow or rain. If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center . The monitor may malfunction, causing an electric shock or fire. Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. Failure to do so may cause an electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable.
Resumen del contenido incluido en la página 8
Do not insert metal objects such as chopsticks, wire and gimlet or inflammable objects such as paper and match into the vent, headphone port or AV ports or etc. It may cause a fire or an electric shock. If an alien substances or water flows into the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center. If you view a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to e
Resumen del contenido incluido en la página 9
Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, leading to electric shock or fire. Do not place children’s favorite objects (or anything else that may be tempting) on the product. Children may try to climb on the product to retrieve an object. The product could fall, causing physical damage or even death. Good Postures When Using the Monitor Try to maintain a good posture when using the monitor. Keep your back straight. K
Resumen del contenido incluido en la página 10
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Without Stand With Basic Stand Manual Warranty Card User's Guide, (Not available in all Quick Setup Guide Monitor Driver, locations) Natural Color software Cable D-sub Cable Power Cord
Resumen del contenido incluido en la página 11
Front Opens the OSD menu. Also use to exit the OSD menu or return to 1. MENU button [ ] the previous menu. 2. MagicBright button MagicBright is a new feature providing optimum viewing [] environment depending on the contents of the image you are watching. Currently four different modes are available: Custom, Text, Internet, and Entertain. Each mode has its own pre- configured brightness value. You can easily select one of four settings by simply pressing MagicBright c
Resumen del contenido incluido en la página 12
once as the monitor saves your adjustments. See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor off when it is not needed, or when leaving it unattended for long periods. Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port Connect the power cord for your monitor to the power port on the back of the monitor. 2. D-sub 15-pin port Connect
Resumen del contenido incluido en la página 13
1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. 2. 2-1. Using the D-sub (Analog) connector on the video card. Connect the D-sub cable to the 15-pin, D-sub connector on the back of your monitor. Connected to a Macintosh. 2-2. Connect the monitor to the Macintosh computer using the D-sub connection cable. Turn on your computer and monitor.
Resumen del contenido incluido en la página 14
Monitor and Bottom Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant Mounting interface pad . A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the Mounting interface pad with the holes in the rear cover mounting
Resumen del contenido incluido en la página 15
Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China) 1. Insert CD into the CD-ROM drive. 2. Click . "Windows" 3. Choose your monitor model in the model list, then click the "OK" button. 4. If you can see following message window, then click the "Continue An
Resumen del contenido incluido en la página 16
http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China) ® ® Microsoft Windows XP Operating System 1. Insert CD into the CD-ROM driver. 2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced..". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Drive
Resumen del contenido incluido en la página 17
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following " " window, then click the " " button. Then Message Continue Anyway click " " button. OK This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9. Click the "Close" button then
Resumen del contenido incluido en la página 18
10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. Click "Start" , "Setting" , "Control Panel". 2. Double click the "Display" Icon. 3. C
Resumen del contenido incluido en la página 19
frequency by referring to the Preset Timing Modes in the user guide. Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. 1. Press Enter at the first and the second screen after executing the X86Config file. 2. The third screen is for . setting your mouse 3. Set a mouse for your computer. 4. The next screen is for . selecting a keyboard 5. Set a keyboard for your computer. 6. The next screen is
Resumen del contenido incluido en la página 20
How to delete the Natural Color software program Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program". Select Natural Color from the list and then click the "Add/Delete" button.
