Manual de instrucciones de New Buck Corporation 80ZC

Resumen del contenido incluido en la página 1

The following manual is for
the 80ZC cabinet ONLY. If
you require information on the
Model 80 unit that fits inside
this cabinet, please download
the Model 80 manual from the
“Stove Manuals” section of
our website. Thank you for
choosing Buck Stove!

Resumen del contenido incluido en la página 2

MODEL 80 ZC CABINET INSTALLATION FEATURES: INSTALLATION: MAINTENANCE: PREPARATION: OPERATION: SAFETY: NEW BUCK CORPORATION 1992 NARNOCK HERSEY

Resumen del contenido incluido en la página 3

IMPORTANTI The Top Panel (#1 ) And Side-Panels (#2) Must Be Installed _On Cabinet Before Setting The Cabinet For Framing. tf.\ TOP PANEL - ~ ~ INSllATION CAP~ " I TeP PANEL h, _ ~ ~ I KfiA'l" IKIM I f- -P r FRONT FRONT LOUVl:RS I I INSLlAT ION LAYERS~ I I 0 0 0 >tx ~'xx :L~ I- , >\ ~it1- ~ FRONT --1 LLI LLI --1 ~ Q LzJ =' Q 2: (/) (/) ~ :z: :z: ~ == 0 0 LLI ~ 8J 8J ~ LLI ~ ~ Q Q E2 E5 E2 (f) (f) V) l.J.. l.J.. ~ ~ ~ SIDE PANEL ~ ( o 0 0 FRONT,VIEW SIDE VIEW

Resumen del contenido incluido en la página 4

CAUTION - Refer to chimney manufacturers instructions for assembly and disassembly of chimney parts. Be sure to follow chimney instructions for proper clearances to combusti­ bles and proper air spacing required. -',- Chlmnoy Cap -1- ~pp

Resumen del contenido incluido en la página 5

CAUTION: Do not mix Ch imney Parts as a fire. may re su 1t. Use one model of listed chimney parts completely for·an instal~ation. CAUTION: Read through all of these instructions carefully. Follow Chimney Manufacturer's Installation exactly. Failure to install the Cabinet, Stove, and Chimney as described in the instructions will void the manufacturer's warranty. A major cause of chimney related fires is failure to maintain required clearances (air spaces) to combustible materials. It is of utmost

Resumen del contenido incluido en la página 6

INSTALLATION PRECAUTIONS The following precautions are mandatory for a safe installation: A. Compliance with local building codes and regulations is mandatory. B. Be careful not to damage unit in handling and unpacking component parts and accessories. C. Use only listed approved chimney pipes. D. The chimney must extend a minimum of three feet above the hig'hest point where it penetrates the roof (three feet above a flat roof or up to a 2/12 pitch roof), and the chimney must extend a minimum of

Resumen del contenido incluido en la página 7

A. Straight up through ceiling: (See Figures 1 and 2). This is a simple installation normally used when installing a Hodel ZC-80 inside an existing room, and in iome cases, in new construction. Refer to Figure 3 if an offset to clear an obstruction is needed. CAUTION- Refer to chimney manufacturers instructions for assembly and disassembly of chimney parts. Be sure to follow chim­ ney instructions for proper clearances to combustibles and proper air spacing required. 4~¥-- Chimney Cap Chimney Ca

Resumen del contenido incluido en la página 8

FRAMING CONSTRUCTION Except as noted, the Hodel ZC-80 can be installed almost anywhere you desire. There are, however, a few clearance and framing restrictions that must be followed. See figures 1 and 2 to make sure that these clearance restrictions are met. It is much wiser to place your Hodel ZC-80 correctly at the start of the installa­ tion than to be forced to relocate it after much of the work is done. You must ensure that the floor is of adequate strength to accept the load of this unit.

Resumen del contenido incluido en la página 9

Framing must be accomplished after the Model ZC-80 is set in place. The chimney can be installed after framing, but installa­ tion is considerably more difficult and, in some cases, impossi­ ble. Therefore, it is recommended that the chimney be installed prior to framing when a choice exists. '~ ~t: LJ ± lZ rr~'Bl.lllzm

Resumen del contenido incluido en la página 10

2. Set Hodel ZC-80 unit in place and attach safety shield to unit as shown in Figure i-A and i-B. You must place a noncom­ bustible material 3/4" thick millboard or equivalent K Factor 2 =.084/BTU/F H0F inches minimum. 3. Frame the ZC Cabinet usng 2"x 4" studs or local building code framing. Some minor framing restrictions are required: A. Adjacent side walls must be at least 6" from the outer edge of the Cabinet trim panel. B. The overall opening dimensions must be at least 47 1/2" Hide and 41

Resumen del contenido incluido en la página 11

CAUTION! Refer to chimney manufacturers instructions for assembly and disassembly of chimney parts. Be sure to follow chimney instructions for proper clearances to combusti­ bles and proper air spacing Chimney Cap required. //?~-- Chimney Pipe "Y~ .....4-'::;"':~-- 2" x." Siudding Doubl. H••der -+1---- A Double Header must be used on a load bearing wall. This must be done 12" above cabinet. Singi. H••der A Single Header must be used as part of front Iraming, vertical 2" ....·s must be turned fla

Resumen del contenido incluido en la página 12

CAUTION! Refer to chimney manufacturers instructions for assembly and disassembly of chimney parts. Be sure to follow chimney instructions for proper clearances to combusti­ bles and proper air spacing required. ffi--- Chimney Cap 0--\.--1- Storm Collar ---:f-- Roof Flashing -+ Chimney Pipe ,.....e;~~"'-7"'5..-s-'lt-ttt1-- Use Fire Code Sheet Rock -"'C-~7"''-?.-s-'S1'f--i-H-tt+f-- Met al Fire Slop NOTE: A Double Header must be used on a load bearong ....all as illustrated in F.gure 3. 2" • 4" St

Resumen del contenido incluido en la página 13

Install pipe to cabinet by pushing down over the ~tarter section of pipe on the ZC Cabinet. NOTE: To ease installation of the first section of pipe to the Cabinet use a pipe crimping tool and crimp the bottom of the inside chimney liner. Install pipe to cabinet by pushing down over the starter section of pipe on the ZC Cabinet. Maintain a 2 inch minimum clearance Attach sheet metal clips (2 ea.) to pipe and cabinet top to assure stability. WARNING! Do not pack required air spaces on top of cabin

Resumen del contenido incluido en la página 14

INSTALLING FIRESTOP RADIATION SHIELD: Nail the firestop Radia­ tion Shield to' the bottom of the framed ceiling opening using at least two 8-penny nails per side. CHIMNEY INSTALLATION INFORMATION ROOF CLEARANCE ROOF Frame a square opening in roof maintaining the required 2" /' rr= clearance to combustible materials between the chimney and the framed opening and roofing material. ATTIC INSULATION RADIATION FIRES TOP RADIATION SHIELD Provides proper clearance. 2" clearance does not app~y. CEILING

Resumen del contenido incluido en la página 15

Electrical procedures: The ZC-80 Cabinet is not pre-wired; an electrician must wire the Cabinet into the home wiring. system using No. 14 AWG (with ground wiring) as minimum in accordance with local wiring codes. (See Figure 9) 1. Remove receptacle cover. 2. Remove receptacle from mounting box. 3. Run No. 14 AWG wire directly from house wiring in through the Field Connector in the lower right side of the Cabi­ net. Leave 4-6 inches of wire extending out of the box. 4. Tighten Field Connector aro

Resumen del contenido incluido en la página 16

FINISHING Finishing can now be completed using the desired material in accordance with local building and fire codes. CAUTION: Do not cover any opening on the Cabinet; heat must be allowed to escape from the openings designed into the unit. A grilled trim panel is provided with the trim package to cover this area. Also, the grilled opening at the bottom front of the Cabinet cannot be blocked. Optional Fire Code Sheet Rock A hearth extension must extend to a minimum of 16" in front of the fire­ p

Resumen del contenido incluido en la página 17

INSTALLING THE MODEL 80 BUCK STOVE Install unit as follows: A. Carefully reinspect chimney connections, vent outputs and cabinet air intakes after finishing is completed. B. Thoroughly clean all masonry mud and debris from cabinet and surrounding environment. C. Ensure that Cabinet has not been damaged during masonry pro­ cess. D. Remove protective plastic wrapping from stove. E. Inspect motor_and associated hardware for damage. F. Slide the Buck Stove Model 80 into the Cabinet all the way to th

Resumen del contenido incluido en la página 18

H. Install the trim kit attaching it to the Cabinet or finished framing by using 1" screws to secure the trim panels in place. I. Remove cover plate from Cabinet exposing receptacle. Roll up pOHer cord so it will fit inside of cover box. Plug in pOHer cord in receptacle. Re­ place cover plate. (See Figure 10). ~. .... FIGURE 10 / / Cover o / Plate """, Sheet Metal Screws 16