Résumé du contenu de la page N° 1
EXA2955-9/21 9/21/01 4:45 PM Page 1
Cordless
Telephone
with Answering System
Instruction Manual
900 MHz
EXA2955
Résumé du contenu de la page N° 2
EXA2955-9/21 9/21/01 4:45 PM Page 2 Precautions! Important Safety Instructions Before you read anything else, please observe the When using your telephone equipment, these basic following: safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury Warning! to persons: Uniden America Corporation DOES NOT 1. Read and understand all instructions. represent this unit to be waterproof. To reduce the 2. Follow all warnings and instructions marked risk of f
Résumé du contenu de la page N° 3
EXA2955-9/21 9/21/01 4:45 PM Page 3 D. If the product does not operate normally Important Electrical Considerations when following the operating instructions. Unplug all electrical appliances when you know an (Adjust only those controls that are covered electrical storm is approaching. Lightning can pass by the operating instructions. Improper through your household wiring and damage any adjustment of other controls may result in device connected to it. This phone is no exception. damage and
Résumé du contenu de la page N° 4
EXA2955-9/21 9/21/01 4:45 PM Page 4 Radio Interference • Keep the base and handset away from sources Radio interference may occasionally cause buzzing of electrical noise such as motors or and humming in your cordless handset, or clicking fluorescent lighting. noises in the base. This interference is caused by • Be sure there is sufficient space to fully extend external sources such as TV, refrigerator, vacuum the base antenna. cleaner, fluorescent lighting, or electrical storm. • The base ca
Résumé du contenu de la page N° 5
EXA2955-9/21 9/21/01 4:45 PM Page 5 Table of contents 29 Transferring a call Getting Started 29 To transfer from the base 6 Read this first phone to the handset 7 Step 1:Checking the package 30 To transfer from the handset contents to the base phone 8 Step 2:Setting up the base phone 31 Having a three-way conference 11 Step 3:Preparing the battery 31 To join the phone pack conversation 13 Identifying the parts Answering Machine Basics Features 16 Making calls 32 Setting up the answering machi
Résumé du contenu de la page N° 6
EXA2955-9/21 9/21/01 4:45 PM Page 6 Getting Started Read this first Before you use your phone, you must first set it up. Here's a quick way to set up your phone: Steps 1, 2 and 3. Step 1 (page 7) First, unpack the phone and the supplied accessories. Step 2 (pages 8 to 10) Next, you need to do three things to set up the base phone, including finding the best location for the base phone. Base phone Step 3 (pages 11 to 12) Then, insert the battery pack into the handset and charge it for 15-20 ho
Résumé du contenu de la page N° 7
EXA2955-9/21 9/21/01 4:45 PM Page 7 Step 1 Checking the package contents Make sure you have received the following items in the package. AC power adapter (AD-314) Base phone Handset Telephone line cord (1) Wall bracket/stand Rechargeable battery for base phone pack (BT-905) Uniden Parts Department (800) 554-3988 Hours: M-F 7:00 AM to 5:00 PM CST. We can also be reached on the web at www.uniden.com Getting Started 7
Résumé du contenu de la page N° 8
EXA2955-9/21 9/21/01 4:45 PM Page 8 Step 2 Setting up the base phone Do the following steps: • Choose the best location • Connect the base phone • Choose the dialing mode Choose the best location Where you place the base phone affects the reception quality of the handset. Away from noise sources such as a window by a street with heavy traffic Away from television sets and other Away from heat sources, such as radiators, electronic equipment airducts, and sunlight Away from a microwave oven A
Résumé du contenu de la page N° 9
Getting Started EXA2955-9/21 9/21/01 4:45 PM Page 9 Connect the base phone If you want to hang the base phone on the wall, see page 47. Route the code 3 To an AC outlet To DC IN 9V To LINE 2 AC power adapter (supplied AD-314) Align the ∆ marks. Telephone line cord 1 (supplied) To the telephone outlet If you want to use the wall bracket as the stand, attach it on the bottom of the base phone before step 1 as illustrated above. 1 Connect the telephone line cord to the LINE jack and to a telepho
Résumé du contenu de la page N° 10
EXA2955-9/21 9/21/01 4:45 PM Page 10 Step 2: Setting up the base phone (continued) Notes • Use only the supplied AD-314 AC power adapter. Polarity of the plug Do not use any other AC power adapter. • Connect the AC power adapter to a continuous power supply. • Place the base phone close to the AC outlet so that you can unplug the AC power adapter easily. Modular Tip If your telephone outlet is not modular, contact your telephone service company for assistance. Choose the dialing mode For the
Résumé du contenu de la page N° 11
Getting Started EXA2955-9/21 9/21/01 4:45 PM Page 11 Step 3 Preparing the battery pack Charge the battery pack for 15-20 hours before you start using your phone. 1 Slide open the battery compartment lid of the handset. 2 Connect the battery connector with correct polarity (black wire goes on left side and red wire goes on BT-905 right). Red Black 3 Close the battery compartment lid. 4 Place the handset on the base phone. The CHARGE LED lights up when the handset is properly seated on the char
Résumé du contenu de la page N° 12
EXA2955-9/21 9/21/01 4:45 PM Page 12 Step 3: Preparing the battery pack (continued) Battery duration A fully charged battery pack lasts for about: • approx. 7 hours when you use the handset continuously. • approx. 7 days when the handset is in standby mode. Notes • The battery pack will gradually discharge over a long period of time, even if not in use. • If you leave the battery pack in the handset without charging it, the battery pack will be completely discharged. It may require several
Résumé du contenu de la page N° 13
Getting Started EXA2955-9/21 9/21/01 4:45 PM Page 13 Identifying the parts Refer to the pages indicated in parentheses for details. Handset 1 Antenna 10 OFF button (p. 16, 19) Allows you to disconnect the call. 2 Speaker 11 FLASH button (p. 16, 19) 3 TALK/BATT LOW LED (p. 16, 20) 12 HOLD button (p. 16, 19, 26) Lights up during a call, flashes when Used to hold a call. you store a phone number for memory 13 INTERCOM button (p. 27) dialing. Used to make an intercom call. 4 VOL (volume) switch (
Résumé du contenu de la page N° 14
EXA2955-9/21 9/21/01 4:45 PM Page 14 Identifying the parts (continued) Base Phone 1 Message counter (p. 37) 8 IN USE LED (p. 17, 19, 25) Indicate the number of new messages Lights when one of the phones is in recorded. “A” appears in the use. announcement only mode. “FL” 9 CHARGE LED (p. 11) appears when there is no space to Lights while the battery is being record messages. charged. 2 TIME/SET button (p. 32, 45) 10 MIC (microphone) (p. 33, 44) Press when setting the day and time, or 11 TONE
Résumé du contenu de la page N° 15
Getting Started EXA2955-9/21 9/21/01 4:45 PM Page 15 17 REC/MEMO button (p. 33, 44) 24 INTERCOM button (p. 28) Records a greeting or memo Used to make an intercom call. message. 25 INTERCOM LED (p. 27) 18 ERASE button (p. 34, 40) Lights up during an intercom call. Erases the recorded greeting or 26 SPEAKER (PHONE) button messages. (p. 17, 19) 19 PLAY/STOP (MAILBOX 1,2,3) Used to make or receive a call with button (p. 39) the base phone. Plays back the messages in each 27 SPEAKER (PHONE) LED m
Résumé du contenu de la page N° 16
EXA2955-9/21 9/21/01 4:45 PM Page 16 Basics Making calls 1 Pick up the handset from the base phone. TALK 2Press . TALK/BATT The TALK/BATT LOW LED on the LOW LED handset and the IN USE LED on the base phone light up. Then you’ll hear a dial tone. If you FLASH VOL hear error beeps, move closer to the switch CHANNEL base phone. HOLD 3 Dial the phone number. 4 When you’re done talking, press TONE * OFF or replace the handset on the base phone. The TALK/BATT LOW LED on the REDIAL/P handset and the
Résumé du contenu de la page N° 17
Basics EXA2955-9/21 9/21/01 4:45 PM Page 17 If the handset battery becomes weak during a call You hear a beep every three seconds and the TALK/BATT LOW LED on the handset flashes. The call will disconnect soon. Replace the handset on the base phone to charge. For optimum performance, charge the battery for 15-20 hours. Note that during the first 10 - 15 minutes of charging, the phone will be inactive, i.e., unable to make or receive a call. After this initial 10 - 15 minutes, you may be able
Résumé du contenu de la page N° 18
EXA2955-9/21 9/21/01 4:45 PM Page 18 Making calls (continued) To obtain the best speakerphone performance • You may not be able to hear the other party’s voice in a noisy place. Therefore, use the speakerphone in a quiet room. • Do not bring your hand or other object too close to the microphone or you will hear a shrill noise (“feedback”). • When the speaker volume is loud, or the telephone has been placed close to a wall, you may find that the volume drops suddenly. This is due to a circuit
Résumé du contenu de la page N° 19
Basics EXA2955-9/21 9/21/01 4:45 PM Page 19 Receiving calls 1 When you hear the phone ring; TALK • Press TALK/BATT OFF (or any key except ). LOW LED or • Pick up the handset from the base phone when the handset is placed on the base phone. VOL FLASH The TALK/BATT LOW LED on switch the handset and the IN USE HOLD LED on the base phone light up. 2 When you’re done talking, press CHANNEL OFF or replace the handset on TONE * the base phone. The TALK/BATT LOW LED on the handset and the IN USE LED
Résumé du contenu de la page N° 20
EXA2955-9/21 9/21/01 4:45 PM Page 20 Telephone Features Memory dialing You can dial with a touch of a few buttons by storing a phone number on a dialing key. You can store up to 10 different phone numbers separately on the handset and on the base phone. Storing phone numbers on the handset 1Press . SET UP The TALK/BATT LOW LED flashes. 2 Press one of the dialing keys TALK/BATT LOW LED 0 9 ( to ) for the phone number to be stored. You’ll hear a confirmation beep. TALK 3 Enter the phone number
