Instruction d'utilisation Sony Cyber-shot DSC-S40

Résumé du contenu de la page N° 1

How to hardwire the Sony DSC-S40 Digital Camera

CopyrightÓ, PixController http://www.PixController.com, all rights reserved.





This document covers in detail how to modify the Sony DSC-S40 digital camera for remote shutter control from the
PixController Universal or LE camera control board. Please see http://www.pixcontroller.com or email
support@pixcontroller.com for more information.

Please note that if you make this modification to your Sony camera that you will void your

Résumé du contenu de la page N° 2

Remove batteries and media card Before starting your project be sure to remove the 2 AA internal batteries and the Media Card. Remove the 2 AA batteries and Media Card Remove the camera case screws Remove all 3 screws from the camera case. Be sure to place the screws in a safe place while modifying the camera. Remove screws 1,and 2 from the bottom of the camera case. Note, screw 2 is under the memory card door. Remove screw 3 from the right side of the case

Résumé du contenu de la page N° 3

Remove the case Carefully remove the back of the camera case from the camera exposing the interior electronics, Figure 1. Next, remove the front of the camera case, Figure 2. This is a little harder to remove, but take your time and unsnap all of the hinges. The front of the case will be attached with a small ribbon cable, so take care as not to handle this too hard or damage the ribbon cable. Figure 1 Figure 2 Prep the S40 Shutter Assembly Cable You must use the S40

Résumé du contenu de la page N° 4

Insert the Shutter Assembly Cable The next step is to insert the S40 Shutter Assembly cable into the shutter connector. Locate the shutter connector shown in Figure 4. Using a small pair to tweezers with smooth jaws carefully remove the cable from this connector. Carefully grab the base of the ribbon cable and take your time to remove this cable. Next insert the S40 Shutter cable, which will be sandwiched in with the current cable. Insert the cable in the orientation as show

Résumé du contenu de la page N° 5

Figure 6 Attach the ground wire Next attach the ground wire, which is a small gauge wire, and in our example we added a black wire. This wire is soldered to one of the UBS hood solder pads on the back of the camera near the LCD display. Figure 7 shows the exact location. The modification is now complete. You can drill a small hole in the Tripod connector and run the 3 wires, Power, Shutter, and Ground through this location, or add any connector you wish. We leave this desi

Résumé du contenu de la page N° 6

Re-attach case and replace the screws Once you are complete with this process place the camera case back together and replace the camera case screws. Attaching the Sony S40 to the PixController LE Board and Universal Board 1. Wiring your S40 camera to the PixController LE board. Connect the following wires to your LE board: Shutter – Shutter on LE, J2-1 Ground – Ground on LE, J2-2 Power – Refresh on LE, J2-3 Last, remove the R17 resistor from the LE board, see:

Résumé du contenu de la page N° 7

PixController Universal Phone Port Completed Modification

Résumé du contenu de la page N° 8

Zoom Lens issue Because of the zoom lens on the Sony S40 this can be an issue to get a good seal between the camera lens and the case as to not get flash bleed during night photos. Figure 8 shows a simple solution to this problem by adding 3 of the Large Flash Masking Washers sold on the www.pixcontorller.com web site under the camera accessories. These 3 washers can be easily glued together using Marine GOOP. Figure 8 CopyrightÓ Ó Ó Ó, P