Résumé du contenu de la page N° 1
®
Installation/Operation
CC3551H-2 and CC3651H-2X
DSP Color Camera
C1984M-F (4/03)
Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.com
USA & Canada: Tel: 800/289-9100 • Fax: 800/289-9150
International: Tel: 1-559/292-1981 • Fax: 1-559/348-1120
Résumé du contenu de la page N° 2
IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other appa
Résumé du contenu de la page N° 3
REGULATORY NOTICES This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee tha
Résumé du contenu de la page N° 4
CAMERA LAYOUT BACK FOCUS ADJUSTMENT MOUNT ADAPTER LOCKING SCREW PHASE ADJUSTMENT LEVEL ADJUSTMENT POWER SUPPLY COSMETIC TRIM RING Note: The cosmetic trim ring conceals the LED light for more BACK FOCUS descreet surveillance ADJUSTMENT RING operations. The trim ring also hides the power connectors and BNC VIDEO CONNECTOR LED protects the DIP LENS CONNECTOR DIP SWITCHES switches. Figure 1. Camera Layout INSTALLATION Lens Mounting The camera can use a fixed iris, manual iris or auto iris lens. Th
Résumé du contenu de la page N° 5
Camera Mounting Use a standard 1/4-20 screw (provided) with a maximum thread length of 3/8-inch (10 mm) for top or bottom camera mounting. The mount adapter may be fitted to the top or bottom of the camera. The camera is shipped with the mount adapter located on the top of the camera. 1 To change the mount adapter position: 2 1 Remove the four screws from the mount adapter located on the top of the camera. 2 Remove the trim cover from the bottom of the camera by prying it loose. Place the trim c
Résumé du contenu de la page N° 6
AC operation only – If you are wiring more than one camera to the same transformer, connect one side of the transformer to the same terminal on all cameras, and connect the other side of the transformer to the remaining terminal on all cameras. Failure to connect all of the cameras the same way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between cameras. Table A. Recommended Wire Gauge and Wiring Distances The following are the recomm
Résumé du contenu de la page N° 7
LENS SETUP AND FOCUS PROCEDURES Video Drive Auto Iris Lens Set the lens mode selector switch to AIV. Switch the ESC OFF. Refer to the lens instructions and adjust the lens for the optimum picture (video output level of 1V peak-to-peak). To focus, fully open the iris by covering the lens with a suitable neutral density (ND*) filter. If the viewed scene is 6.5 feet (2 m) away or farther, set the lens focus to infinity (far). Use the back focus adjustment ring (refer to the Back Focus Adjustment se
Résumé du contenu de la page N° 8
ON SWITCH SETTINGS - + L H PHASE LEVEL OFF BLC 1 OFF OPT 2 OFF ESC 3 Note: White indicates AW1 AW2 4 switch setting. AIV AID 5 INT LL 6 NOR SHP 7 OFF LC 8 OFF DS1 9 OFF DS2 10 00027 Figure 6. DIP Switch Default Settings 1 BLC - Back Light Compensation OFF (Default setting) - Disables the BLC mode. BLC - Enables the BLC mode. If a bright backlight is present the subjects in the picture may appear dark or as a silhouette. BLC enhances objects in the center of the picture. 2 OPT - Optima OFF
Résumé du contenu de la page N° 9
8 LC - Long Line Compensation OFF (Default setting) - Disables the Long Line Compensation mode. LC - Enables the Long Line Compensation mode. Boosts the video drive level to 1.25 Vp-p for long line transmission. 9 DS1 and 10 DS2 - Digital Slow Shutter Digital slow shutter slows the picture frame rate and increases the camera sensitivity under low light conditions. Depending on the number of fields of integration the picture will develop a granular appear- ance and motion may show some lag, resu
Résumé du contenu de la page N° 10
CAMERA SYNCHRONIZATION (AC OPERATION ONLY) When using more than one camera power supply, a brief vertical roll may occur on the monitor when a camera view is switched. To eliminate vertical roll, adjust the phase control by synchronizing, or line-lock- ing, the cameras to one another. Use the phase potentiometer located on the side of the camera (refer to Figure 1) to make adjustments. It may be necessary to have two people in communication when synchronizing the cameras: one person at the camer
Résumé du contenu de la page N° 11
the vertical sync pulses of the reference camera to the selected camera(s). SPECIFICATIONS GENERAL CCD Sensor: 1/3-inch interline transfer Picture Elements CC3551H-2: 768 (H) x 494 (V) CC3651H-2X: 795 (H) x 696 (V) Sensing Area: 6 mm diagonally Synchronize System: INT/AC line lock Horizontal Resolution CC3551H-2: 480 TV lines CC3651H-2X: 470 TV lines Iris Control: Electronic/passive Minimum Illumination CC3551H-2: 0.035 lux at f1.2, 50 IRE 0.02 lux at f1.2, 35 IRE CC3651H-2X: 0.02 lux at f1.2, 5
Résumé du contenu de la page N° 12
WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/MC3600 Series); two years on all other cameras. ® ® • Three years on Genex Series (multiplexers, server, and keyboard) and 090 Series Camclosure Camera System. •Two years on 10
