Résumé du contenu de la page N° 1
INSTRUCTION MANUAL
3 CCD CAMERA
IK-TF2
For Customer Use
Enter below the Serial No.
which is located on the
bottom of the cabinet. Retain
this information for future ref-
erence.
Model No.: IK-TF2
Serial No.:
WARNING
This is a Class A of EN55022 product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pur
Résumé du contenu de la page N° 2
SAFETY PRECAUTIONS Read the following safety precautions carefully before using this product. These instructions contain valuable information on safe and proper use that will prevent harm and damage to the operator and other persons. Make sure that you fully understand the following details (indications, graphic sym- bols) before proceeding to the remaining sections in this manual. Indication definitions Graphic symbol definitions Indication Meaning Symbol Meaning This indicates the existence of
Résumé du contenu de la page N° 3
Caution • Note the following instructions when installing. • Do not put an inflammable material on the product. • Do not put the product on an Inflammable material such as carpet or blanket. • Do not block a vent hole. • Do not put the product in a narrow space, since the heat generated from the product may be difficult to emanate. If you do not follow the above, the heat generated by the product may cause fire. • Do not put the product in direct sunshine and/or high temperature. The temperature
Résumé du contenu de la page N° 4
TABLE OF CONTENTS 1CAUTIONS ON USE AND INSTALLATION ........................................... 6 2COMPONENTS...................................................................................... 6 3ITEMS CONTROLLED BY USING ON SCREEN DISPLAY .................. 7 4NAMES AND FUNCTIONS .................................................................... 8 5CONNECTION....................................................................................... 9 5.1 Standard Connection.
Résumé du contenu de la page N° 5
(6) OPTION ..................................................................................................................... 22 (6.1) Changing RS232C communication baud rate ................................................... 22 (7) Setting to factory setting status.................................................................................. 23 7.3 External Sync ............................................................................................................
Résumé du contenu de la page N° 6
1CAUTIONS ON USE AND INSTALLATION Carefully handle the units. Do not drop, or give a strong shock or vibration to the camera. This may cause problems. Treat the camera cables carefully to prevent cable problems, such as cable breakdown and loosened connections. Do not shoot intense light. If there is an intense light at a location on the screen such as a spot light, a blooming and smearing may occur. When intense light enters, vertical stripes may appear on the screen. This is not
Résumé du contenu de la page N° 7
Electronic shutter Gain White balance Process Sync Option 3ITEMS CONTROLLED BY USING ON SCREEN DISPLAY Preset value Item Available selections (Factory setting) MODE MANUAL, SS, EXT TRIG MANUAL 1PULSE SNR1PULSE SR2PULSE EXT TRIG 1PULSE SNR OFF1/100s1/250s1/500s1/1000s1/2000s MANUAL speed OFF 1/4000s1/10000s1/25000s1/50000s FLD 1/525H260/525HOFF1FRM255FRM Syncro. OFF scan. FRM 1/525H260/525HOFF2FRM256FRM FLDFRM Storage mode FLD Trigger
Résumé du contenu de la page N° 8
4NAMES AND FUNCTIONS DC IN 12V terminal Prism faceplate DISP button MENU UP button DATA UP(AWB) button DATA DOWN button MENU DOWN button RGB terminal PAGE button Front Rear Prism faceplate The protection cap is attached on the lens mount portion. After removing the cap, mount the lens. Be careful not to scratch or touch the optical area. DISP button Used when switching the display. PAGE button Used when switching to the menu and when selecting the men
Résumé du contenu de la page N° 9
5CONNECTION 51 Standard Connection Lens Camera cable (option) RGB IK-TF2 DC IN 12V monitor Less than 4mm DC power supply 52 Cautions on Connection When connecting the camera cables, be sure to turn off the camera and the other equipment connected. We suggest using a C mount lens made for a 3CCD camera. When using another lens, the best camera performance of this camera may not be obtained. (For example, low resolution may occur, focus may be lost throu
Résumé du contenu de la page N° 10
6OPERATION Referring to the item “ 5. CONNECTION”, connect each equipment correctly. Turn on the connected equipment and the camera. Pointing the lens at the object, operate the lens iris adjustment, focus adjustment, etc.. Referring to the item “6.1 White Balance”, operate the adjustment. Referring to the items “6.2 Gain, 7. MODE SETTING BY ON SCREEN DISPLAY”, select the necessary items. 61 White Balance For the white balance adjustment for this unit, AWB (A
Résumé du contenu de la page N° 11
Display Meaning AWB OK Automatic white balance adjustment finished correctly. AWB NG Automatic white balance adjustment cannot be performed because the video level is LEVEL LOW too low. Set the video level properly. AWB NG Automatic white balance adjustment cannot be performed because the video level is LEVEL HIGH too high. Set the video level properly. AWB NG Automatic white balance adjustment cannot be performed because the color C TEMP LOW temperature is too low. If the C.T
Résumé du contenu de la page N° 12
62 Gain When the image is dark even if the lens iris is open, change the gain (video gain) to get the proper video level. For the gain adjustment of the unit, MANUAL (Manual) and OFF (0 dB) modes are provided. Select the mode on the GAIN menu. (Refer to the item “7.2 (2) GAIN (Video gain)”.) MANUAL(Manual gain) Gain adjustment is performed on the GAIN menu. The adjustment range is from –3dB to 18dB in 1dB steps. (Refer to the item “7.2 (2) (2.1) (a) Changing the gain in MAN
Résumé du contenu de la page N° 13
7MODE SETTING BY ON SCREEN DISPLAY Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The contents once set are memorized when the power is turned off, so it is unnecessary to set again when using the unit next time. When the setting is performed, select the menu of the item to be set. 71 Using the Menues When the power turns on, the normal screen showing only the video signal appears. Change the output to each screen (vid
Résumé du contenu de la page N° 14
72 Menus Select the menu to change the setting by referring the item “7.1 Using the Menus”.) When the [MENU UP], [MENU DOWN] buttons are pushed, the “” on the screen moves up and down. Move the “” to the item to change. ( 1 ) SHUTTERElectronic shutter The electronic shutter has three modes; MANUAL, SS(Synchro. Scan), EXT TRIG(External trigger). Press the “Page” button to enter the Shutter Page. Use the “Data Up/Down” buttons to select the Shutter Mode. 1
Résumé du contenu de la page N° 15
1 2 Changing each setting in SSsynchro. scanmode Move up and down Set by pushing By pushing DATA UP,DOWN MENU UP,DOWN Shutter mode MANUAL, SS, EXT TRIG -- 1 SHUTTER -- Synchro. scan setting MODE SS 1525H260525HOFF FLD1FRM255FRM SYNCHRO SCAN OFF FRM2FRM256FRM FLDFRM FLD FLD/FRM SW FLD, FRM < MODE = SS > (a) Changing the shutter speed setting
Résumé du contenu de la page N° 16
1 3 Changing each setting in EXT TRIG mode The EXT TRIG has three modes; 1PULSE SNR, 1PULSE SR, 2PULSE. First set the “” to MODE and select EXT TRIG, then set the “” to EXT TRIG and select the desired EXT TRIG mode. 1 3 1 Changing each setting in 1PULSE SNR mode Move up and down Set by pushing By pushing DATA UP,DOWN MENU UP,DOWN Shutter mode MANUAL, SS, EXT TRIG -- 1 SHUTTER -- EXT TRIG mode MODE EXT TRIG 1PULSE SNR,
Résumé du contenu de la page N° 17
1 3 2 Changing each setting in 1PULSE SR mode Move up and down Set by pushing By pushing DATA UP,DOWN MENU UP,DOWN Shutter mode MANUAL, SS, EXT TRIG -- 1 SHUTTER -- EXT TRIG mode MODE EXT TRIG 1PULSE SNR, 1PULSE SR, 2PULSE EXT TRIG 1PULSE SR TRIG PULSE Input trigger pulse setting at 1PULSE SNR and 1PULSE SR EXPOSURE 16ms The rising edge The falling edge Front and back edges of
Résumé du contenu de la page N° 18
1 3 3 Changing each setting in 2PULSE mode Move up and down Set by pushing By pushing DATA UP,DOWN MENU UP,DOWN Shutter mode MANUAL, SS, EXT TRIG -- 1 SHUTTER -- EXT TRIG mode MODE EXT TRIG 1PULSE SNR, 1PULSE SR, 2PULSE EXT TRIG 2PULSE TRIG PULSE Input trigger pulse setting at 2PULSE FLDFRM FLD The rising edge The falling edge Front and back edges of pulse FLD/
Résumé du contenu de la page N° 19
2 GAIN (Video gain) GAIN has two modes; MANUAL, OFF. Set the “” to MODE, push the [DATA UP], [DATA DOWN], and select mode among MANUAL, OFF. In the OFF mode, gain is fixed to 0dB. 2 1 Changing each setting in GAIN Move up and down Set by pushing By pushing DATA UP,DOWN MENU UP,DOWN --2GAIN-- Gain mode MANUAL, OFF MODE MANUAL MANUAL 0dB Manual gain setting -3dB to 18dB(1dB step (a) Changing the gain in MANUA
Résumé du contenu de la page N° 20
3 WHT BAL(White balance) WHT BAL has two modes; AWB, MANUAL. Set the “” to MODE, push the [DATA UP], [DATA DOWN], and select mode among AWB, MANUAL. 3 1 Changing each setting in AWB(Automatic White Balance) mode Move up and down Set by pushing By pushing DATA UP,DOWN MENU UP,DOWN White balance mode setting AWB, MANUAL Color temperature setting 3200K, 5600K -- 3 WHT BAL -- MODE AWB CTEMP 3200K (a) Changing color
