Instruction d'utilisation Fisher & Paykel DD90S(H)TI

Résumé du contenu de la page N° 1

(1,1) -1- 590018A DD36SDD90S DoorPanelPrep USCANZGB.indd 22/2/10 1:49:22 PM (1,1) -1- 590018A DD36SDD90S DoorPanelPrep USCANZGB.indd 22/2/10 1:49:22 PM
Front panel preparation (Integrated models only)
DishDrawer®
DD36STI, DD90S(H)TI models
US CA NZ AU GB IE
Important!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit

Résumé du contenu de la page N° 2

(1,2) -1- 590018A DD36SDD90S DoorPanelPrep USCANZGB.indd 22/2/10 1:49:22 PM (1,2) -1- 590018A DD36SDD90S DoorPanelPrep USCANZGB.indd 22/2/10 1:49:22 PM 2 PANEL PREPARATION The following calculations assume the top of the panel is aligned with the top of the adjacent Installation diagrams for illustration purposes only cabinetry: A width of the panel Measure A (the width between adjacent door/drawer fronts) and write it in the fi rst box below, then complete the equation. min. door clearan

Résumé du contenu de la page N° 3

18” (457 mm) 2 11⁄16 ” (69 mm) Badge zone (2,1) -1- 590018A DD36SDD90S DoorPanelPrep USCANZGB.indd 22/2/10 1:49:22 PM (2,1) -1- 590018A DD36SDD90S DoorPanelPrep USCANZGB.indd 22/2/10 1:49:22 PM 3 PARTS SUPPLIED Supplied separately Attached to product Panel mounting Integrated rectangular badge (1) Panel bracket (1) Integrated door seal (1) screws (14) (Satin chrome supplied) 45 ZONE REQUIRED FOR BADGE REMOVE PANEL BRACKET & DETACH BADGE WARNING ! Electrical Shock Hazard Before continuing, en

Résumé du contenu de la page N° 4

(2,2) -1- 590018A DD36SDD90S DoorPanelPrep USCANZGB.indd 22/2/10 1:49:22 PM (2,2) -1- 590018A DD36SDD90S DoorPanelPrep USCANZGB.indd 22/2/10 1:49:22 PM 6 7 ROUTE BADGE THROUGH PANEL SECURE PANEL BRACKET TO PANEL Important! 1 Use all 14 screws provided as shown. 2 5⁄8” (16 mm) x14 1 2 89 RECONNECT BADGE REATTACH PANEL 2 Important! 2 Ensure the rubber seal between the drawer and panel is kept in place. 1 1 WARNING ! Push the panel 2 Electrical Shock Hazard in then up to Connect the integrat

Résumé du contenu de la page N° 5

(1,1) -2- 590018A DD36SDD90S DoorPanelPrep USCANZGB.indd 22/2/10 1:50:34 PM (1,1) -2- 590018A DD36SDD90S DoorPanelPrep USCANZGB.indd 22/2/10 1:50:34 PM Front panel adjustment (Prefi nished models only) DishDrawer® DD36SDFTX, DD90SDFTM, DD90SDF(H)TX models US CA NZ AU GB IE Important! SAVE THESE INSTRUCTIONS The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your countr

Résumé du contenu de la page N° 6

(1,2) -2- 590018A DD36SDD90S DoorPanelPrep USCANZGB.indd 22/2/10 1:50:34 PM (1,2) -2- 590018A DD36SDD90S DoorPanelPrep USCANZGB.indd 22/2/10 1:50:34 PM 2 DISCONNECT FROM POWER SUPPLY 3 REMOVE FRONT PANEL 2 WARNING ! Electrical Shock Hazard Disconnect the DishDrawer from the power supply. 1 Failure to follow this warning may result in electrical shock, injury or fire. 45 DETACH CONTROLS LOOSEN PANEL BRACKETS 2 1 Lie the door panel flat on its front on a protected surface. Be careful not to dam

Résumé du contenu de la page N° 7

(2,1) -2- 590018A DD36SDD90S DoorPanelPrep USCANZGB.indd 22/2/10 1:50:34 PM (2,1) -2- 590018A DD36SDD90S DoorPanelPrep USCANZGB.indd 22/2/10 1:50:34 PM 6 7 SLIDE BRACKETS TO SUITABLE HEIGHT SETTING TIGHTEN PANEL BRACKETS There are three pre-drilled height settings. Tighten these screws Slide brackets to preferred height setting. Replace these fixing screws Tighten these screws Low setting Factory setting High setting - 1⁄16 ”(1.5 mm) + 1⁄16 ”(1.5 mm) 89 RECONNECT CONTROLS REATTACH PANEL 2

Résumé du contenu de la page N° 8

(2,2) -2- 590018A DD36SDD90S DoorPanelPrep USCANZGB.indd 22/2/10 1:50:34 PM (2,2) -2- 590018A DD36SDD90S DoorPanelPrep USCANZGB.indd 22/2/10 1:50:34 PM 10 RECONNECT THE POWER SUPPLY www.fi sherpaykel.com www.fi sherpaykel.ca www.fi sherpaykel.co.nz www.fi sherpaykel.com.au www.fi sherpaykel.co.uk www.fi sherpaykel.ie 590018A US CA NZ AU GB IE 03.10