Instruction d'utilisation Jettech Metal Products X-32

Résumé du contenu de la page N° 1

LOW TEMP WAREWASHERS
X-32 X-32
Technical Manual
2003 02

Résumé du contenu de la page N° 2

Welcome to JET TECH “creating endless possibilities!” This manual was created specifically for you, the end- user. We have included information to help troubleshoot problems and facilitate resolving those problems. General information pertaining to our range of ware- washers will be covered in this section. Specific information on our current models are available upon request; model by model. If you find any discrepancy or can't find certain information, please contact us. We will be gla

Résumé du contenu de la page N° 3

Warranty MANUFACTURERS LIMITED WARRANTY Jet Tech Systems Corporation (Jet Tech) hereby warrants all new warewashers bearing the name “JET TECH” and installed within the continental United States of America or Canada to be free from defects in material and workmanship, under normal and regular usage and operation, for a period of one (1) year following the date of original installation, (unless specified otherwise) but in no event can exceed eighteen (18) months from the date of shipment from

Résumé du contenu de la page N° 4

Sanitary inner “deep-drawn” wash tank Independent Chemical Pumps Construction features Technical Features cm) m Body , external housing, wash tank, and all m chassis components in brushed stainless steel Rack capacity: 19.75" x 19.75" (50 cm x 50 AISI 304 18/8 cm) (one open combination rack and on peg m dish rack supplied) Reduced operating noise of 58 DbA due to m utilization of double-wall insulated panels Complete cycle: 160 seconds (145 second Wash & 15 second Rinse) m Upper and lower

Résumé du contenu de la page N° 5

DRAIN The X‐32 is equipped with an automatic drain pump that will pump the drain water to a maximum height of 36" (0.9 meter). A 1" ID flexible drain hose is included to facilitate maintenance and servicing of the machine. It is important not to reduce the size of this hose. The drain should have a loop at the back of the dishwasher as per illustration below. The loop should be 36 inches (36”) above the floor and drop down into a drain pipe with an air gap. These instructions must be foll

Résumé du contenu de la page N° 6

ELECTRICAL Unit must be connected with a 110 volts 60Hz line. The terminal block will receive L1, N and Ground wire. Unit must be well grounded. Breaker rating should be 15 amps.

Résumé du contenu de la page N° 7

Getting Started Immediately upon receipt of your new X-32 dishwasher, inspect the dishwasher for any obvious signs of damage. If you do find any traces of damage, contact the transport company that brought the dishwasher to your place at once. A damage claim must be made immediately with the carrier. Please assure that the following items are included with your X-32 dishwasher. ! (1) 20 x 20 open rack ! (1) 20 x 20 peg rack for dishes !4 adjusting feet !1 operators manual 5

Résumé du contenu de la page N° 8

Chemical hook-up This unit is equipped with three (3) chemical pumps. Each will inject a different liquid product at a specific time during the wash cycle. The chemical pumps have sufficient length of tubing hose that can be inserted in gallon containers near the dishwasher. The chemical pumps have colored tubing for ease of identification. The colors are as follow; Red for Detergent Clear for Sanitizer Blue for Rinse-additive To prime the pumps; you must complete two full wash cycles. Y

Résumé du contenu de la page N° 9

Operation 1. When you start the power (GREEN PUSH-BUTTON) TL the machine automatically starts to fill the water until the correct water level is reached. During the fill, the solenoid valve EC and the detergent dosing pump MPD are operating. 2. By pushing the (BLACK ROUND) push-button TC, the programmed washing cycle starts. The length of the times are shown in the schematic electrical diagram: 2.1 From 0" to 30" the machine is washing and only the wash pump is operating. 2.2 From 30" to 50"

Résumé du contenu de la page N° 10

Electrical Schematics DPS - Drain pump By-pass switch MPS - Drain Pump TL - Main Power switch PS1, PS2 - Pressure switches ER - Rinse solenoid valve EC - Fill solenoid valve MPD - Detergent pump MPB - Rinse additive pump MPSA - Sanitizer pump MP - Door switch TLS - Deliming option switch CRP - Contact from relay MT - Timer motor M1, M2, M3, M4, M5 - Timer contact LC - Light, Timer cycle MPL - Wash pump BR - Relay coil TC - Start switch CR - Contactor relay swicth LL - Light, Main power BRP - R