Résumé du contenu de la page N° 1
Dust Collector
INSTRUCTION MANUAL
Sealed Recoverable Hose Dimensions
Net
Peak air flow
suction
capacity length (L x W x H) weight
1.2 m3/min.
2,2 1.5 m 240 mm x 140 mm x 340 mm 2.9 kg
1,200 mm 147")
(42.4 cu.ft./min.)
of water (5 ft.) (9-7/16" x 5-1/2" x 13-3/8") (6.4 Ibs)
Résumé du contenu de la page N° 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using dust collector, safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the followings: READ ALL INSTRUCTIONS BEFORE USING THIS DUST COLLECTOR. 1. PROPER GROUNDING. This tool should be grounded while in use to protect the operator from electric shock. Connect to a properly grounded outlet only. See “Grounding Instructions”. 2. GUARD AGAINST ELECTRIC SHOCK. Prevent body conta
Résumé du contenu de la page N° 3
switch emits sparks when turned ON and OFF, and so does the motor commutator during operation. A dangerous explosion may result. 13. Do not allow to be used as a toy. Close attention is neccessary when used by or near children. 14. Use only as described in this manual. Use only MAKITA's recommended attachments. 15. Never use the dust collector in the rain. When not in use, store the dust collector indoors. 16. Do not use close to heat source (stoves, etc.). This can cause discoloration
Résumé du contenu de la page N° 4
GROUNDING INSTRUCTIONS This appliance must be grounded. If it should malfunction or breakdown, ground- ing provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment- grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. WARN IN G - Improper connection of the equipment
Résumé du contenu de la page N° 5
Attaching shoulder strap and waist belt Attach the shoulder strap to the dust collector using holes in the top and side of the dust collector as shown in the figures below. Always secure the shoulder strap using the buckles. Shoulder ~~ strap Attach the waist belt to the dust collector using holes in the side of the dust collector as shown at right. Hang the dust collector on your back and adjust the shoulder strap length so that you can carry the dust collector on your back comforta
Résumé du contenu de la page N° 6
Operation 1) When using without your power tool connected : To start the dust collector, press the "ON' side of the switch. Press the "OFF" side of the switch to stop. Switch 2 When using with your power tool con- nected : This dust collector has an outlet for ac- OUl cepting the plug of your power tool. When your power tool is plugged into this outlet and the dust collector is switched on, the dust collector will be in its "AUTO-ON" condition and will start or stop automatically
Résumé du contenu de la page N° 7
Cord hook Use the convenient cord hook as shown at Cord hook right to prevent the power tool cord from dangling around your legs. Your legs may get tangled with the dangling cord, causing severe injury to you. Cleaning lever A clogged filter causes poor suction per- formance and potential damage to the Cleaning lever motor. Occasionally use the cleaning lever to clear the dust from the filter. If suction performance becomes poor, move the cleaning lever back and forth about ten ti
Résumé du contenu de la page N° 8
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Cleaning filter If suction performance will not recover enough even after you use the cleaning lever to clear the dust from the filter and empty out the dust and dirt, proceed as follows to clean the filter. Loosen the four screws which secure the I Hose the filter with clean water to remove any dust from it. Be careful not to damage the filter with
Résumé du contenu de la page N° 9
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Hose Nozzle assembly Part No. 150269-7 (1.5 m : 4.9 ft) Part No. 122234-6 Part No. 150327-9 (3 m: 9.8 ft) 0 Belt assembly Waist belt Part No. 122416-0 Part No. 163335- 1 0 Straight pip
Résumé du contenu de la page N° 10
The following dust extractor attachments, joints and sleeves are available for use with some types of Makita rotary hammers, finishing sander and random orbit sander. Description Applicable model Rotary hammers HR1821, HR2000 HR2511 Dust extractor attachment Part No. 192176-8 Finishing sander 9036 B Random orbit sander BO5000 Rubber sleeve 18-21 Part No. 422021-6 NOTE : Makita concrete planer Model PC1100, belt sander Model 9401 and wheel sander Model 9741 can be connected direc
Résumé du contenu de la page N° 11
Nov -20-'91 US DUST COLLECTOR Model 420s Note: The switch and other part configurations may differ from country to country. 11
Résumé du contenu de la page N° 12
/;:hi MODEL 4205 NO Nov-20-'91 US ITEM NO. DESCRIPTION DESCRIPTION USEO NO. USEO T MACHINE ~ Cord 30 1 SUPpOrl cover Cord Guard 31 4 Taoping Screw BT 4x20 i1 i Tapping screw 4x18 32 1 Terminal Base Complete 41 1 Stram Relief 33 1 Ball Bearing 607110 Strain Relief 34 1 Flat Washer 7 Housing Sei IWilh Item 461 35 1 insulation Washer 71 Name Plate 36 1 ARMATURE ASSEMBLY 81 Hook lW8th Item 33 371 91 Main Filter 37 1 Ball Bearing 608DDW 10 4 Tapping screw 4x10 30 1 Field 11 1
