Résumé du contenu de la page N° 1
®
AVerMedia
AVerDiGi
EB3004 MD
User Manual
June 2009
Résumé du contenu de la page N° 2
FCC NOTICE (Class A) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. .Federal Communications Commission Statement NOTE- This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These li
Résumé du contenu de la page N° 3
WARNING TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION IF THERE IS ANY DAMAGE, SHORTAGE OR INAPPROPRIATE ITEM IN THE PACKAGE, PLEASE CONTACT WITH YOUR LOCAL DEALER. WARRANTY VOID FOR ANY UNAUTHORIZED PRODUCT MODIFICATION NOTICE - INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. - THE INFORMATION CONTAINED HEREIN IS TO BE CONSIDERED FOR REFERENCT ONLY. LIGHTNING WARNING − TO AVOID THE LIGHTNING STR
Résumé du contenu de la page N° 4
Table of Contents Chapter 1 Introduction ................................................................................ 1 1.1 Package Content .................................................................................................. 1 1.2 Features and Specifications ................................................................................. 1 1.3 Front Panel ........................................................................................................... 2
Résumé du contenu de la page N° 5
Chapter 1 Introduction 1.1 Package Content (4) (1) (3) (2) (8) (5) (7) (6) (1) AVerDiGi EB3004 MD unit (2) Remote Control (batteries included) (3) Quick User Guide (4) Power Cord * The power cord varies depending on the standard power outlet of the country where it is sold. (5) Power Adapter (6) Internal HDD holder (8 screws are inculded) (7) Software CD (User Manual included) (8) USB Cable 1.2 Features and Specifications Fire resistance
Résumé du contenu de la page N° 6
Scheduled recording (00:00~23:00 set by hour ) Search for recorded video files by date/time/event Input/Output: 4 sensor inputs and 1 relay output control Audio In/Out: 4 audio in and 1 audio out 1.3 Front Panel Name Function Light when the unit is power on (1) DVR Power LED Indicate the hard disk running state. Light when the HDD is running (2) HDD LED (Read/Write) (3) IR Sensor Receive signal from the remote control to operate the unit (4) IR Sensor Port To connect extend
Résumé du contenu de la page N° 7
Name Function (5) Audio Out Output the audio signal to a audio out device such as speaker The audio output device has its own power supply is necessary. i (6) Sensor In Support 4 sensor devices (7) Alarm Out Support 1 relay device (Relay: 1A @ 125V AC/30V DC) (8) RS-232 For PTZ camera connection and firmware update (9) FAN speed Switch Adjust fan speed(High/Low) according to the actual environment situation We do strong recommend that adjust the fan speed to High when the operating
Résumé du contenu de la page N° 8
3. Secure the brackets on the hard disk 4. Connect the the SATA cable and the power connector to the hard disk 5. Secure the hard disk inside the unit then place 6. Push the cover forward and secure the cover unit cover 7. You may now connect all the cables. When the power is connected, the Power LED light turns on 4
Résumé du contenu de la page N° 9
1.5.2 Connecting Devices The back panel of the DVR unit, user can connect up to 4 video cameras, 4 sensor devices, 1 alarm device and output video to a TV or CRT/LCD monitor. Connecting the unit to the PC, then use the bundled software enables user to transfer, playback and segment the video. Follow the illustration below to make the connection: Each time you change the video display output or video system (NTSC/PAL), the power must be turned off and on to reset the DVR unit. 5
Résumé du contenu de la page N° 10
1.5.3 Connecting the Audio, Sensor and Relay device The Sensor, Alarm, and audio port enable you to connect 4 sensor inputs, 1 relay outputs, and 4 audio in and 1 audio out device. Just connect the external sensor, relay, and audio in/out device pin directly to the pinhole. The RS-232 port can be used for PTZ camera connection through a RS-232 to RS-485 converter. Check the table below and locate which pinhole is assigned to sensor input, relay output, and audio in/out. The signal fro
Résumé du contenu de la page N° 11
Sensor in and Alarm pinhole: Pin # Definition 11 Sensor 1 signal 12 Sensor 1 Ground signal 13 Sensor 2 signal 14 Sensor 2 Ground signal 15 Sensor 3 signal 16 Sensor 3 Ground signal 17 Sensor 4 signal 18 Sensor 4 Ground signal 19 Relay signal 20 Relay signal RS-232 pinhole: Pin # Definition 21 RS-232 TX signal 22 RS-232 RX signal 23 RS-232 Ground signal 24 RS-232 RX signal 7
Résumé du contenu de la page N° 12
▲ Chapter 2 Operating the DVR unit 2.1 Familiarizing the Remote Control Buttons Use the Remote control to operate the OSD menu on surveillance screen. Button Function A functional key for multiple DVR system (1) FN remote control Switch to Channel 1 (2) 1 As a number key for entering password Switch to Channel 2 (3) 3 As a number key for entering password Switch to Channel 3 (4) 7 As a number key for entering password Switch to Channel 4 (5) 9 As a number key for entering passwo
Résumé du contenu de la page N° 13
▼ Button Function To move the selection to the left and right (16) ▲ To go up and down and select the items in the menu list or change the settings ▼ ZOOM+ To zoom in view of PTZ camera (17) ZOOM- To zoom out view of PTZ camera PTZ PTZ camera control button. Press + camera channel PTZ (18) button( 1 2 3 4 )can enter PTZ mode to control PTZ camera.(see 2.1.3) SPEED+ To speed up movement of PTZ camera lens (19) SPEED- To speed down movement of PTZ camera lens FOCUS
Résumé du contenu de la page N° 14
▲ 2.1.1 Using AB Repeat Function AB Repeat function allow user to set a video segment from A to B point and play on the surveillance screen until user stop. 1. Press (play button) to call out the SEARCH MODE menu to find the recorded video that user wants to playback. 2. Select TIME SEARCH or EVENT LIST. - TIME SEARCH (search by date and time): select the date and time from where you want to begin the video playback. - EVENT LIST (search by condition): select from the list. A-B 3. Du
Résumé du contenu de la page N° 15
2.1.2 Controlling PTZ Camera Using remote control, user can easily control PTZ camera at local site. Before starting, make sure the PTZ camera is connected with the DVR unit. And then, please go to OSD menu to enable PTZ control (see also 3.1 Menu Function: PTZ Setup). Use the RS-232 to RS-485 converter to connect the PTZ camera with the DVR unit. i 2.1.2.1 To Enter the PTZ Mode PTZ To control PTZ camera, user need to enter the PTZ mode first. Press button, and 1 2 3 4 ) camera chann
Résumé du contenu de la page N° 16
▼ ▼ 2.1.2.2 To Set Preset Position User can set 9 preset positions for PTZ camera. Using 1 to 9 button to set the preset position. PTZ 1 2 3 4 ) 1. Press and camera channel number button ( to enter PTZ mode. ▲ ▼ 2. Using , , and to adjust the lens of the PTZ camera to the position that user wants. 3. Press any number button over 3 seconds and the position will be saved. 4. To move the PTZ camera to preset position, just press the number button. 2.1.2.3 To Control PTZ Camera To move,
Résumé du contenu de la page N° 17
2.2 Using the DVR for the First Time 1. Make sure all devices and power cables are well connected. 2. Turn on the DVR unit by connecting the power cable into the power plug. 3. User should see the windows appear on the surveillance screen. SYSTEM INITIALIZE The system will do hard disk detection automatically. ▲ 4. For the first time use hard disk, please format the hard disk. Using and ▼ to go up and down and press to make a selection. Select HDD FORMAT and press (YES) to format har
Résumé du contenu de la page N° 18
2.3 Surveillance Screen This chapter will describe the symbols on the surveillance screen and screen display mode. While DVR is playback, the record action will keep working and the surveillance screen will playback the recorded video. Surveillance Screen Preview Mode Symbol Description DVR is recording Audio is enabled Speaker is available Motion recording Hard disk capacity 5% 14
Résumé du contenu de la page N° 19
Playback Mode Symbol Description Playback the recorded video Audio is enabled AB segment is set and playing Recorded video is playback at backward speed(2x, 4x, 8x, 16x, 32x, or 64x) Recorded video is playback at faster forward speed(2x, 4x, 8x, 16x, 32x, or 64x) A Always Recording B Button Recording M Motion Recording Screen type User can switch to display each channel in full screen or 4 channels in D1, D1 Enhanced, or CIF record mode. QUAD Screen Mode Full Screen Mo
Résumé du contenu de la page N° 20
2.3.1 Setup the Time Stamp Current date and time could be displayed on each channel screen by enabling TIME STAMP function. Please follow the below steps to enable TIME STAMP. 1. Press to call out OSD menu. ▲ ▼ 2. Using and move the highlight to CAMERA/RECORD and press to make a selection. 3. Select and press to make a selection. GENERAL 4. And then, select TIME STAMP by pressing button. ▲ 5. Using and ▼ to select the disable/enable of TIME STAMP and press or to confirm. GEN
