Instruction d'utilisation Metra Electronics 99-7423

Résumé du contenu de la page N° 1

INSTALLATION INSTRUCTIONS FOR PART 99-7423
APPLICATIONS
NISSAN Altima
2007-2011
99-7423
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
• A) Radio Housing • B) Radio Housing Trim Plate • C) Radio Housing Brackets
• D) Double DIN Trim Plate • E) Double DIN Brackets • F) ISO Brackets • G) Pocket
• H) (2) Climate Control Trim Panels • I) (2) #8 3/8” Screws
F
C
D E
B
Ha

Résumé du contenu de la page N° 2

99-7423 TABLE OF CONTENTS Dash Disassembly - NISSAN Altima 2007 -2011 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - ISO Mount Radio Provision with Pocket . . . . . . . . . . .. . . . . . . . . . . . . . . . . . 4 - Double

Résumé du contenu de la page N° 3

99-7423 DASH DISASSEMBLY NISSAN ALTIMA 2007-2011 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove trim panel between the shifter and the radio/ cli- mate control panel. (Figure A) 3 Remove (2) Phillips screws exposed behind panel below radio/climate control panel. (Figure A) 4 Unclip and remove the climate control vent trim panel then remove (2) B Phillips screws exposed behind panel. (Figure B) 5 Unclip, unplug and remove entire radio/cl

Résumé du contenu de la page N° 4

99-7423 KIT PREPARATION NISSAN ALTIMA 2007-2011 A 1 Clip the corresponding climate control trim panel into the radio housing. Note: There are (2) different climate control trim panels. One for auto cli- mate control and one for manual cli- mate control. (Figure A) 2 Attach the (2) radio housing brackets to the climate controls using the fac- tory screws. (Figure B) 3 Attach the bracket/climate control assembly to the radio housing using B the (2) #8 3/8” screws supplied with this kit. (Figure C)

Résumé du contenu de la page N° 5

99-7423 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 3 Attach the radio housing trim plate supplied with the kit to the assembly. 4 Snap in the pocket into the assembly. B (Figure C) Continue to final assembly. C 3

Résumé du contenu de la page N° 6

99-7423 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio with the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Attach the radio housing trim plate supplied with the kit to the assembly. (Figure B) 4 Snap the pocket into the assembly. B (Figure C) Continue to final assembly. C 4

Résumé du contenu de la page N° 7

99-7423 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing assembly. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing assembly. (Figure B) 3 Slide the Double DIN radio into the bracket/radio housing assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure C) B 4 Snap the Double DIN trim plate onto the fr

Résumé du contenu de la page N° 8

99-7423 KIT ASSEMBLY STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing assembly. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing assembly. (Figure B) 3 Slide the stacked ISO units into the bracket/radio housing assembly and secure the units to the kit using the screws supplied with the units. (Figure C) B 4 Snap the Double DIN trim plate onto the fron

Résumé du contenu de la page N° 9

99-7423 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disasse

Résumé du contenu de la page N° 10

99-7423 NOTES 8

Résumé du contenu de la page N° 11

99-7423 NOTES 9

Résumé du contenu de la page N° 12

99-7423 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 12/10/10 © COPYRIGHT 2007-2010 METRA ELECTRONICS CORPORATION INST99-7423