Résumé du contenu de la page N° 1
Résumé du contenu de la page N° 2
FOR YOUR SAFETY If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, immediately call your gas supplier or your fire department. IMPORTANT SAFETY INFORMATION 1. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. 2. When cooking with oil/grease, do not exceed 350˚ F (177 C). Do not store or use extra cooking oil in the vicinity of this or any other appliance. 3. Remember: An LP cylin
Résumé du contenu de la page N° 3
WARNING READ AND UNDERSTAND BEFORE USING THIS PRODUCT 1) Use the products only outdoors, and only on a noncombustible surface such as brick, concrete, or dirt. NOT SUITABLE are surfaces such as wood, asphalt or plastic which may burn, blister, or melt. Do not use under any overhang or roof and keep a minimum of 10 feet of clearance on all sides of the cooker. DO NOT LEAVE UNATTENDED WHILE COOKER IS IN USE OR IS STILL HOT (ABOVE 100˚F). 2) Leak test gas connections before use. (See Use and Care
Résumé du contenu de la page N° 4
® 8) King Kooker products are designed for use with propane gas, with the regulator supplied with the product, and must never be used with natural gas. Accessories not recommended by Metal Fusion, Inc., must ® not be used with King Kooker appliances. 9) See Use and Care section for LP Gas Cylinder information. 10) Consumption of alcohol and drugs will impair the consumer’s ability to safely assemble and use these products, and must be avoided when the cookers are in use and when the cooking oil
Résumé du contenu de la page N° 5
READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE ® USING YOUR KING KOOKER PRODUCT TABLE OF CONTENTS Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Résumé du contenu de la page N° 6
METAL FUSION, INC. LIMITED ONE-YEAR WARRANTY WHAT THIS WARRANTY COVERS This warranty covers all components of this outdoor cooker to be free from defects in materials and workmanship, with the exceptions stated below. HOW LONG COVERAGE LASTS This warranty runs for one year from the date of purchase. WHAT IS NOT COVERED This warranty does not cover the following: Incidental and Consequential Damages. This warranty does not cover incidental and consequential damages arising in any way out of the u
Résumé du contenu de la page N° 7
OWNER’S REGISTRATION ® Dear Customer, Thank you for purchasing a King Kooker®! Please take a moment to fill out your registration form and return it to us. We are always happy to hear suggestions and comments from our customers about our products. Completion of this registration allows us to contact you if the need arises. Name: __________________________________________________________ Address: ________________________________________________________ _________________________________________
Résumé du contenu de la page N° 8
TAPE HERE FOLD ________________________ Place ________________________ Stamp ________________________ Here METAL FUSION, INC. 712 St. George Avenue Jefferson, LA 70121 FOLD 8
Résumé du contenu de la page N° 9
Résumé du contenu de la page N° 10
Figure 2 HOSE WITH FEMALE FITTING AND ADJUSTABLE REGULATOR. COOKING POT ADJUSTABLE REGULATOR VENTURI TUBE P.O.L. CONNECTION (LEFT HAND THREAD) AIR SHUTTER SPRING HALF UNION BURNER LP GAS 3/8 FEMALE TANK FLARE SWIVEL The air shutter, spring and half union as pictured should already be assembled to the casting. Figure 2 Check that fitting is tightened to the venturi tube and that the elbow points downward. If loose, wrench tighten the 3/8 female flare swivel to the brass half union. Figure 3 HOS
Résumé du contenu de la page N° 11
JET BURNER ASSEMBLY INSTRUCTIONS TOOLS REQUIRED: ADJUSTABLE WRENCH, LEAK TESTING SOLUTION 1. Before assembling, check that all cooker components are included in the shipping carton, as per Figure 4. 2. Read and understand assembly instructions. Figure 4 Jet Burner Assembly ADJUSTABLE REGULATOR P.O.L. CONNECTION (LEFT HAND THREAD) BRASS ADAPTER 3/8 FEMALE FLARE SWIVEL JET BURNER LP GAS (SOME MODELS MAY HAVE NEEDLE TANK VALVES AND PRESSURE REGULATORS AS PER FIGURE 3) ORIFICE CAP (DO NOT REMOVE THI
Résumé du contenu de la page N° 12
CAMP STOVE ASSEMBLY INSTRUCTIONS TOOLS REQUIRED: ADJUSTABLE WRENCH LEAK TESTING SOLUTION 1. Procedures for assembly of all Camp Stoves is the same, only the number of burners vary. 2 Place burner frame on side so that the CASTING VENTURI casting ends are turned upward. TUBES 3. Loosen nuts on bottoms of castings and AIR SHUTTERS remove all castings from frame. SPRINGS 4. Remove the air shutter and spring from the bag and place the air shutter over the end of the casting venturi tube. Hold the wi
Résumé du contenu de la page N° 13
101 PK ASSEMBLY INSTRUCTIONS WARNING The following warnings are to be followed when using the 101 PK in addition to all other warnings listed in this manual. Observe these safety precautions when using a 14.1 or 16.4 oz. portable propane cylinder. 1. Always inspect appliance, propane cylinder and propane connections for damage, dirt or debris before attaching propane cylinder. 2. Protect propane cylinder from excessive heat. 3. Screw propane cylinder into appliance and hand tighten only. Do not
Résumé du contenu de la page N° 14
11” CAST COOKER ASSEMBLY Required Tools: Adjustable Wrench and Leak Testing Solution 1. Wrench tighten the brass control valve to the 11” casting. 2. Wrench tighten the brass 3/8” flare swivel fitting to the brass control valve. 3. Tighten left handed threads on POL nut hand tight to the cylinder and then secure with a wrench. Caution: Do not turn regulator or nipple. 4. The hose to burner (brass adapter) connection must be tightened and leak tested. See leak test instructions before use. 5. Go
Résumé du contenu de la page N° 15
Résumé du contenu de la page N° 16
CAMP STOVE LEG ASSEMBLY Required Tools: Adjustable Wrench 1. Match the holes in each leg with corresponding holes in cooker. 2. Slide 1/4” x 1” bolt through each of the twelve holes. These should be directed inward as in the illustration so 1/4"x1" bolts (12) that the nuts will be on the inside of the assembly. 3. Screw 1/4” nut onto each bolt and wrench tighten. Make certain every bolt and nut assembly is completely tightened so the unit will stand sturdily with no sway when the unit is upright
Résumé du contenu de la page N° 17
CS 5 LEG ASSEMBLY Required Tools: Adjustable Wrench 1. Match the holes in each leg with corresponding holes in cooker. 2. Slide 1/4” x 1” bolt through each of the twelve holes. These should be directed inward as in the illustration so that the nuts will be on the inside of the assembly. 3. Screw 1/4” nut onto each bolt 1/4"x1" and wrench tighten. Make certain every bolt and nut Bolts (12) assembly is completely tightened so the unit will stand sturdily with no sway when the unit is upright. CS 8
Résumé du contenu de la page N° 18
106 PK AND 106 PKPT EXTENSION LEGS ASSEMBLY INSTRUCTIONS Required Tools: Adjustable Wrench 1. Match the holes in each leg with corresponding holes in cooker. 2. Slide one 1/4” x 1” bolt through each of the three holes in each extension leg and cooker leg. These should be directed inward so that the nuts will be on the inside of the assembly. 3. Screw 1/4” nut onto each bolt and wrench tighten. Make certain every bolt and nut assembly is completely tightened so the unit will stand sturdily with n
Résumé du contenu de la page N° 19
MODEL #TWT WORKTABLE ASSEMBLY Required Tools: Adjustable Wrench This unit is designed to be used as a worktable for the preparation of turkeys for frying and for draining afterwards. It is not intended for any other use. It is to be used only with Deep Fryer Turkey Packages. This worktable assembly is NOT for use with Model #3018. 1. Stand worktable and cooker side by side, as in the illustration, on a level, sturdy, non-combustible surface. 2. Hold the side of the worktable with the brackets n
Résumé du contenu de la page N° 20
SECTION II USE AND CARE CONNECTION INSTRUCTIONS 1. Check that your 20 lb. LP gas cylinder is not over-filled. The maximum weight of a properly filled cylinder is approximately 38 lbs. 2. Verify that the cylinder valve has the proper connection for a P.O.L. appliance fitting. 3. Attach the regulator to the cylinder by the lefthand threaded P.O.L. fitting. The P.O.L. nut must be wrench tightened with the regulator positioned upright. LEAK TEST 4. Before lighting the appliance, a thorough leak te
