Résumé du contenu de la page N° 1
P/N 60502 & 60505
1994/1995 GM LT1 FUEL INJECTION
WIRE HARNESS INSTALLATION
INSTRUCTIONS
Manual P/N 90517
Copyright © May 2002
PAINLESS PERFORMANCE PRODUCTS
2501 Ludelle Street - Fort Worth, Texas 76105-1036 - (817) 244-6898
E-Mail: tech@painlessperformance.com Web: painless@painlessperformance.com
Résumé du contenu de la page N° 2
We have attempted to provide you with as accurate instructions as possible, and are always concerned about corrections or improvements that can be made. If you have found any errors or omissions, or if you simply have comments or suggestions concerning these instructions, please write us at the address on the cover and let us know about them. Or, better yet, send us a fax at (817) 244-4024 or e-mail us at painless@painlessperformance.com. We sincerely appreciate your business.
Résumé du contenu de la page N° 3
TABLE OF CONTENTS 1.0 INTRODUCTION.......................................................................................................................... ii 2.0 ABOUT THESE INSTRUCTIONS............................................................................................... ii 3.0 TOOLS NEEDED.......................................................................................................................... 1 4.0 PRE-INSTALLATION AND HARNESS ROUTING GUIDELINES.........
Résumé du contenu de la page N° 4
LIST OF TABLES Table 4.1 Compatible Parts.............................................................................................................. 3 Table 6.1 Dash Section Connections................................................................................................ 8 Table 6.2 Engine Section Connections............................................................................................. 10 Table 6.3 Tail Section Connections........................................
Résumé du contenu de la page N° 5
3.0 TOOLS NEEDED In addition to your regular tools, you will need, at least, the following: Crimping tool NOTE: USE A QUALITY TOOL TO AVOID OVER-CRIMPING. Wire stripper Continuity tester CAUTION: DO NOT USE A TEST LIGHT TO TEST THE COMPUTER OR SENSOR WIRING OR YOU WILL DAMAGE THE COMPUTER. Electric drill 1 5/8" Hole saw (for the rubber grommet in the firewall) 4.0 PRE-INSTALLATION AND HARNESS ROUTING GUIDELINES The installation of your harness kit will consist of two p
Résumé du contenu de la page N° 6
To keep the check engine light from coming on you will need to plug in a canister purge solenoid and air pump relay to the wires in the dash section. (The computer looks for signals from these controls and does not care if the actual devices are installed.) 4.2 YOU SHOULD GET TO KNOW THE PARTICULAR ENGINE YOU ARE USING: NOTE: The 94 & 95 LT1 engine has two oxygen sensors, one on the right side and one on the left side of the engine. This system has four rectangular connectors at
Résumé du contenu de la page N° 7
LT1 Fuel Injection Harness (94 & 95) Part # 60502 or 60505 Main Computer............................Service#16188051 EGR. Solenoid................................ Delco# 214-396 Brake Switch.....................................GM# 25524845 Gear Indicator Switch..................GM# 15705308 or Intake Air Temperature.....................GM# 12110319 Delco #D2286A Ignition Module.............................Delco# D-1986-A MAP Sensor ....................................
Résumé du contenu de la page N° 8
5.2 ROUGH INSTALLATION CAUTION: DISCONNECT THE POWER FROM YOUR VEHICLE BY REMOVING THE NEGATIVE BATTERY CABLE FROM THE BATTERY. Note: Make no wire connections or permanent mounting of any kind at this time. 5.2.1 Position the computer and sensors in their intend locations. 5.2.2 Drill a 1-5/8" hole for the firewall grommet near the computer for the engine group and tail section to pass through. 5.2.3 Route the engine group and tail section through the hole. Push the grom
Résumé du contenu de la page N° 9
CAUTION: BE SURE THE IGNITION IS OFF WHEN YOU RECONNECT THE BATTERY OR YOU WILL DAMAGE THE COMPUTER. 6.0 GM 94 & 95 LT1 SYSTEM WIRE HARNESS INSTALLATION INSTRUCTIONS 6.1 CONTENTS OF THE 60502 OR 60505 WIRE HARNESS KIT Take inventory to see that you have everything you are supposed to have in this kit. If anything is missing, contact the dealer where you obtained the kit or contact Painless Performance at (817) 244-6898. The kit should contain the following items: ~ The m
Résumé du contenu de la page N° 10
WHEN THE KEY IS IN THE START AND RUN POSITION. This is the power wire for the fuel injection harness. If the pink wire is connected correctly, the check engine light will come on when the ignition is "ON or START". D. Locate the Orn/Blk and Blk/Wht wires in the dash group. These two wires are for the Park/Neutral INDICATOR Switch, NOT the Neutral Safety Switch. If you have a GM column then you can use the combination switch P/N 15679680 and wire it as described in paragraph 2 or 3
Résumé du contenu de la page N° 11
FIGURE 6.3 Brake Switch Relay FIGURE 6.4 Gear Indicator Switch 7
Résumé du contenu de la page N° 12
F. If you are using the recommended brake switch then you will wire it according to Figure 6.2. The pink wire to the back of the switch in the illustration is the wire that has power on it whether or not the brake is being applied. CAUTION: FAILURE TO WIRE THIS SWITCH CORRECTLY WILL RESULT IN A DANGEROUS SITUATION ON THE VEHICLE. G. If your vehicle has a pressure type brake switch, you may use a relay as shown in Figure 6.3. The relay must be a SPDT Relay and wired correctl
Résumé du contenu de la page N° 13
FIGURE 6.8 Fuel Pump Relay Connector FIGURE 6.7 Air Pump Connection 6.3 ENGINE GROUP INSTALLATION The engine group is designed to be separated into left side (driver) and right side (passenger) sections. Each side is tie-wrapped separately, BUT NOT LABELED. The right side of the engine has the connectors for the idle air control, throttle position sensor, distributor, and map sensor, all of which ARE labeled. When you begin routing, FIR
Résumé du contenu de la page N° 14
6.3.6 Engine Section Connections WIRE COLOR # OF POSITIONS LABELED CONNECT TO: IN CONNECTOR Brown, Gray 2 EGR EGR Solenoid Blue 1 Knock Knock Sensor Purple/White,
Résumé du contenu de la page N° 15
FIGURE 6.11 Oxygen Sensor FIGURE 6.12 MAP Sensor FIGURE 6.13 Injectors 1, 3, 5, 7 FIGURE 6.14 Injectors 2, 4, 6, 8 FIGURE 6.16 IAC FIGURE 6.15 TPS Sensor 11
Résumé du contenu de la page N° 16
FIGURE 6.18 Distributor FIGURE 6.17 MAF Sensor i FIGURE 6.19 Ignition Module FIGURE 6.20 Coil FIGURE 6.21 ECT Sensor FIGURE 6.22 IAT Sensor 12
Résumé du contenu de la page N° 17
6.4 TAIL SECTION INSTALLATION 6.4.1 Locate the tail section that you earlier separated from the engine group. Begin routing it towards the rear of the vehicle. Be sure to avoid all sharp edges, moving or hot parts, or anything else that may damage the harness. 6.4.2 If you ARE using the 4L60E transmission, route the 13-position connector to the transmission and attach it. 6.4.3 If you ARE NOT using the 4L60E transmission, tape up the connector and store it in the harness.
Résumé du contenu de la page N° 18
FIGURE 7.1 Fuse Identification 7.1 THE "CHECK ENGINE" LIGHT Normally, the "check engine" light should come on when the ignition is turned on, then go out a few moments after the engine starts running. If it reappears, or stays on while the engine is running, the computer has detected a problem and a trouble code has been set. 7.2 RETRIEVING TROUBLE CODES FROM THE COMPUTER The chart below shows the type of ALDL test connector each vehicle came wi
Résumé du contenu de la page N° 19
7.2.6 Trouble Code Chart, Diagnostic Trouble Code (DTC) DTC 11 = Malfunction Indicator Lamp DTC 13 = Bank 1 (left) Heated Oxygen Sensor (HO2S) Open Circuit DTC 14 = Engine Coolant Temperature (ETC) Sensor Circuit (Signal Voltage Low) Overheated DTC 15 = Engine Coolant Temperature (ETC) Sensor Circuit (Signal Voltage High) Engine cold DTC 16 = Distributor Ignition System (Low Resolution Pulse) DTC 18 = Injector Circuits DTC 21 = Throttle Position (TP) Sensor Circuit (Signal Volta
Résumé du contenu de la page N° 20
DTC 83 = Reverse Inhibit System (Manual Transmission) DTC 83 = TCC PWM Solenoid Circuit Fault (Automatic Transmission) DTC 84 = Automatic Transmission 3-2 Control Solenoid Circuit DTC 84 = Skip Shift Solenoid Circuit (Manual Transmission) DTC 85 = Transmission TCC Stuck "ON" DTC 90 = Transmission TCC Solenoid Circuit (Manual Transmission) DTC 91 = Skip Shift Lamp Circuit DTC 97 = VSS Output Circuit DTC 99 = Tach Output Circuit TABLE 7.1 Diagnostic Trouble Codes 7.3 WHEN TO
