Résumé du contenu de la page N° 1
TM
Excellence in Motion
TM
FORCE
POWER DRIVE
MICROSTEPPING
Operating
Instructions
Résumé du contenu de la page N° 2
Microstepping MForce PowerDrive Product Manual Changelog Date Revision Changes 04/05/2007 R040507 Initial Release 03/20/2008 R032008 Added CW/CCW to the list of clock option labels for the differential input version. Functionality is the same as the up/down clock type. Added qualification os personnel and intended use statements to inside front. Added PWM Motor Settings to Section 2.6. The information in this book has been carefully checked and is believed to be accurate; however, no responsib
Résumé du contenu de la page N° 3
Important information The drive systems described here are products for general use that conform to the state of the art in technology and are designed to prevent any dangers. However, drives and drive controllers that are not specifically designed for safety functions are not approved for applications where the functioning of the drive could endan- ger persons. The possibility of unexpected or un-braked movements can never be totally excluded without additional safety equipment. For this re
Résumé du contenu de la page N° 4
This page intentionally left blank
Résumé du contenu de la page N° 5
Table Of Contents Getting Started: Microstepping MForce PowerDrive .................................................................1-1 Before You Begin ....................................................................................................................... 1-1 Tools and Equipment Required ................................................................................................. 1-1 Connecting the Power Supply ...............................................................
Résumé du contenu de la page N° 6
Enable Input .....................................................................................................................19 Clock Inputs .....................................................................................................................20 Optocoupler Reference ................................................................................................................22 Input Connection Examples .......................................................................
Résumé du contenu de la page N° 7
List of Figures Figure GS.1: Minimum Logic and Power Connections ............................................................. 1-1 Part 1: Hardware Reference Figure 1.1.1: Microstepping MForce PowerDrive ...................................................................... 1-5 Figure 1.2.1: MForce PowerDrive Mechanical Specifications ..................................................... 1-8 Figure 1.2.2: P1 — 12-Pin Locking Wire Crimp Pin Configuration ........................................
Résumé du contenu de la page N° 8
Appendices Figure A.1: MD-CC300-000 ....................................................................................................A-3 Figure A.2: MD-CC300-000 Mechanical Specifications ............................................................A-3 Figure A.3: Typical Setup, Adapter and Prototype Development Cable ....................................A-4 Figure A.4: Hardware Update Wizard .......................................................................................A-4 Figure A.5:
Résumé du contenu de la page N° 9
WARNING! The MForce has components Getting Started which are sensitive to Electrostatic Discharge Microstepping MForce PowerDrive (ESD). All handling should be done at an ESD protected workstation. Before You Begin WARNING! Hazardous voltage levels may be The Getting Started Section is designed to help quickly connect and begin using your Microstepping MForce present if using an open PowerDrive. The following examples will help you get a motor turning for the first time and introduc
Résumé du contenu de la page N° 10
Connect Opto Reference and Logic Inputs Using 22 AWG wire, connect the Opto Reference to the desired reference point. The reference will determine whether or not the logic input is sinking or sourcing. If Sinking Inputs are desired, connect the Opto reference to a +5 to +24 VDC Supply. If Sourcing Outputs are desired, the Opto Reference needs to be connected to the Controller Ground. Connect the Step and Direction inputs to the appropriate outputs of your PLC or controller. Connecting the Mot
Résumé du contenu de la page N° 11
TM FORCE POWER DRIVE MICROSTEPPING Part 1: Hardware Reference Section 1.1: Introduction to the Microstepping MForce PowerDrive Section 1.2: Microstepping MForce PowerDrive Detailed Specifications Part 1: Hardware Specifications 1-3
Résumé du contenu de la page N° 12
Page Intentionally Left Blank Microstepping MForce PowerDrive Manual Revision R032008 1-4
Résumé du contenu de la page N° 13
SECTION 1.1 Introduction to the Microstepping MForce PowerDrive The Microstepping MForce Pow- erDrive is a high performance, low cost microstepping driver that delivers unsurpassed smoothness and perfor- mance achieved through IMS’s advanced 2nd generation current control. By applying innovative techniques to con- trol current flow through the motor, resonance is significantly dampened over the entire speed range and audible noise is reduced. Microstepping MForce PowerDrives accept a
Résumé du contenu de la page N° 14
Features and Benefits • High Performance Microstepping Driver • Advanced 2nd Generation Current Control for Exceptional Performance and Smoothness • Single Supply: +12 to +75 VDC • Low Cost • Extremely Compact • High Output Current: Up to 5 Amps RMS, 7 Amps Peak (Per Phase) • 20 Microstep Resolutions up to 51,200 Steps Per Rev Including: Degrees, Metric, Arc Minutes • Optically Isolated Logic Inputs will Accept +5 to +24 VDC Signals, Sourcing or Sinking • Automatic Current Reduction • Config
Résumé du contenu de la page N° 15
SECTION 1.2 Microstepping MForce PowerDrive Detailed Specifications General Specifications Electrical Specifications Input Voltage (+V) Range* +12 to +75 VDC Max Power Supply Current (Per MForce PowerDrive)* 4 Amps Output Current RMS 5 Amps Output Current Peak (Per Phase) 7 Amps * Actual Power Supply Current will depend on Voltage and Load. Table 1.2.1: Electrical Specifications Thermal Specifications Heat Sink Temperature -40°C to +85°C Table 1.2.2: Thermal Specifications I/O Specificatio
Résumé du contenu de la page N° 16
Setup Parameters The following table illustrates the setup parameters. These are easily configured using the IMS SPI Motor Interface configuration utility. An optional Parameter Setup Cable is available and recommended with the first order. Microstepping MForce PowerDrive Setup Parameters Name Function Range Units Default MHC Motor Hold Current 0 to 100 percent 5 MRC Motor Run Current 1 to 100 percent 25 1, 2, 4, 5, 8, 10, 16, 25, 32, 50, µsteps per MSEL Microstep Resolution 64, 100,108, 125,
Résumé du contenu de la page N° 17
Pin Assignment and Description P1 12-Pin Locking Wire Crimp Connector Option - Power, I/O and SPI Communications Pin Assignment - P1 Power, I/O and SPI NEED A CABLE? Connections The following cables and converters are Pin # Function Description available to interface Pin 1 N/C No Connect with P1: Pin 2 N/C No Connect The Signal applied to the Optocoupler Reference will 12-Pin Locking Wire Crimp determine the sinking/ or sourcing configuration of the inputs. PD12-1434-FL3 Pin 3 Opto Refer
Résumé du contenu de la page N° 18
NEED A CABLE? P3 Connector - DC Power, 2-Pin Locking Wire Crimp The following cables Pin Assignment - P3 Power and converters are available to interface 2-Pin Locking Function Description with P3: Wire Crimp Pin 1 +V +12 to +75 VDC, 4 Amps Maximum per MDrive34Plus. 2-Pin Locking Wire Crimp Pin 2 GND Power Supply Return. PD02-3400-FL3 Table 1.2.8: P3 Connector WARNING! Do not Recommended Connector Shell and Pins plug or unplug DC Power with power Shell: Molex P/N 510-67-0200 applied. Pins:
Résumé du contenu de la page N° 19
Options and Accessories Parameter Setup Cable and Adapters The optional 12.0' (3.6m) parameter setup cable part number MD-CC300-000 facilitates communications wiring and is recommended with first order. It connects from the 10-Pin IDC Connector located at P2 to a PC's USB port. If the12-pin pluggable locking wire crimp connector is used at P1, adapter MD-ADP-1723C is required to use the MD-CC300-000. USB to SPI ...............................................................................
Résumé du contenu de la page N° 20
Page Intentionally Left Blank Microstepping MForce PowerDrive Manual Revision R032008 1-12
